Zhongdi ZD-932 User manual

Temperature Controlled Soldering Station
Model：ZD-932
1. Features
• Perfect for board level assembly and repair.
• Temperature sensor incorporated into the heating element.
• Rotary temperature setting.
• Slim but heat resistant silicon handle.
• The base, soldering iron, cable, built-in stand and sponge holder are included.
• Temperature range is 150-450’C.
2. Technical Specifications
Voltage: 110-130V 60Hz
220-240V 50Hz
Power: 40W
Temperature: 150-450˚C
3. Operation
3.1 Place the soldering iron in the holder and connect the plug to the receptacle on the station and turn clockwise to
tighten the plug nut.
3.2 Check that the available power supply corresponds to the voltage specifications for the soldering station and the
power switch is in the OFF position.
3.3 Connect the mains plug to a socket and turn on the soldering station by using the power switch
(I=ON/0=OFF). When turned on, the power switch is lit.
3.4 Regulate the desired temperature of the soldering iron with the adjusting knob.
4. Safety
4.1 The manufacturer assumes no liability for uses other than those described in the operating instructions or for
unauthorized alterations.
4.2 The operating instructions and cautions should be read carefully and kept in an easily visible location near the
soldering station. Non-compliance to the cautions can result in accidents, injury or other health risks.
4.3 The power cord should only be plugged in to approved power sockets or adapters.
4.4 The temperature of the soldering tip can reach as high as 450℃（842℉）when powered up.
Since mishandling may lead to fire, be sure to comply with the following safety precautions:

•Do not touch metallic parts near the soldering tip.
•Do not use this product near flammable items.
•Advise others in the work area that the unit can reach very high temperatures and should be considered
potentially dangerous.
•Turn off the power switch when unit is not in use.
•Before replacing parts or storing the product:
1. Turn off the power.
2. Unplug it.
3. Allow soldering iron time to cool to room temperature.
Warning: The soldering iron should always be placed in the stand when not in use.
A fire may result if the appliance is not used with care, therefore:
•Caution when using in places where there are combustible materials
•Do not apply soldering tip to the same place for a long time
•Do not use around or near explosive materials
•Place the soldering iron in its stand after use and allow it to cool to room temperature before storage
•Do not leave the appliance unattended when on
5. Caution
Do not use this tool for any applications other than soldering or desoldering.
Do not wrap the iron against the workbench or otherwise subject the iron to severe shocks.
Do not file the soldering tip to remove any oxide, please wipe the tip on the cleaning sponge.
Use only accessories or attachments that are approved for use with this soldering station. Use of unapproved tools and
other accessories can lead to potential injury, and void any warranty.
Please turn off the power before connecting or disconnecting the soldering iron.
5.1 Before use, the soldering station should be carefully inspected for damage. Please make sure that all power
connections are properly secured. Damaged safety devices such as the soldering iron holder and other parts must be
repaired or replaced by a qualified technician prior to use.
5.2 Do not use this soldering tool in a moist or wet environment. The soldering iron should be placed in the holder
after use.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 and
supervised.
Do not operate the appliance with a damaged plug or cord, after a malfunction or after being dropped or
damaged in any way. If the supply cord is damaged, it must be replaced by a qualified engineer in order to
avoid injury or hazard. The soldering iron must be placed on its stand when not in use.