ZIEHL-ABEGG FXDM25 User manual

Fcontrol
FXDM25/32AM
Frequency inverter with integrated sine lter for 3 ~ fans
Operating Instructions
Keep for reference!
Software version: from Version 11.12
L-BAL-E212-GB 1451 Index 003 Part.-No.
english

Content
1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1 Structure of the operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.3 Exclusion of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4 Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Explanations of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4 Requirements placed on the personnel / due diligence . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5 Start-up and during operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.6 Working on device / Hazards through “residual voltage” . . . . . . . . . . . . . . . . . . . . . . . 8
2.7 Modifications / interventions in the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.8 Operator’s obligation of diligence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.9 Employment of external personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Operational area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.4 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.5 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.6 Disposal / recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Minimum space requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3 Prerequisites for mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.4 Outdoor installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.5 Installation location for agriculture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.6 Temperature influences during commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2 Terminal compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.3 EMC-compatible installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.3.1 Motor cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.3.2 Control cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.3.3 Harmonics current and line impedance for devices > 16 A and ≤ 75 A . . . . . . . . . 14
5.4 Mains connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.4.1 Line voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.4.2 Required quality attributes for the mains voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.4.3 Leakage current, securely attached, ground wire double up to 10 mm² . . . . . . . . . 15
5.5 Residual-current-operated protective device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.6 Inverter output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.6.1 Motor connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.6.2 Disconnection between controller and motor (repair switch) . . . . . . . . . . . . . . . . . 15
5.7 Motor protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.8 Signal input or sensor connection (E1, E2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.9 Analog output (0 - 10 V) “A1” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.10 Voltage supply for external devices (+24V, GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.11 Add-on module type Z-Modul-B Part-No. 380052 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.12 Digital inputs (D1, D2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operating Instructions Fcontrol – model series FXDM25/32AM
L-BAL-E212-GB 1451 Index 003 Part.-No.
2/123

5.13 Relay outputs (K1, K2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.14 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.14.1 RS-485 interface for MODBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.14.2 Automatic addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.15 USB-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.16 Potential at control voltage connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.17 Bypass circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.18 Manual Bypass-Switch type S-D-25 and S-D-50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6 Controls and Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.1 Multipurpose LC display and keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.2 Example for programming mode 2.01 in “Base setup ” . . . . . . . . . . . . . . . . . . . . . . . 22
6.3 Menu structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7 Base setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.1 Mode and signal input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.2 Operation with a second control circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.3 External Setpoint / External speed setting in manual operation . . . . . . . . . . . . . . . . . . 28
8 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.1 Prerequisites for commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.2 Procedure for commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
9 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9.1 Speed controller 1.01 ... 1.02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9.1.1 Base setup 1.01 ............................................... 30
9.1.2 Speed controller with direct setting by keyboard 1.02 . . . . . . . . . . . . . . . . . . . . . . 32
9.2 Temperature control 2.01 ... 2.05 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.2.1 Basic setting 2.01 ... 2.05 ......................................... 34
9.2.2 Settings for operation modes 2.01 ... 2.05 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9.2.3 Functional diagrams temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9.2.4 Additionally for 2.03 (controller output 2 with function
| 6A | ) . . . . . . . . . . . . . . . . . . 38
9.2.5 For mode 2.03 : Relay output for Heating or Cooling . . . . . . . . . . . . . . . . . . . . . . 39
9.2.6 For mode 2.03 Relay output for temperature monitoring . . . . . . . . . . . . . . . . . . . . 40
9.3 Pressure control for condensers refrigeration 3.01 ... 3.04 . . . . . . . . . . . . . . . . . . . . . 41
9.3.1 Base setup 3.01 ... 3.04 .......................................... 41
9.3.2 Setting for operation modes 3.01 ... 3.04 .............................. 42
9.3.3 Functional diagrams pressure control condensers . . . . . . . . . . . . . . . . . . . . . . . . . 44
9.4 Pressure control airconditioning 4.01 ... 4.03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
9.4.1 Base setup 4.01 ... 4.03 .......................................... 45
9.4.2 Setting for operation modes 4.01 ... 4.03 .............................. 46
9.5 Volume control 5.01 ... 5.02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.5.1 Basic setting 5.01 and 5.02 ....................................... 48
9.5.2 Setting for operation modes 5.01 ... 5.02 ............................... 49
9.6 Air velocity control 6.01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
9.6.1 Base setup 6.01 ............................................... 51
9.7 Menu group Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
9.8 Menu group Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
9.9 Controller Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
9.9.1 PIN protection activate, PIN 0010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
9.9.2 PIN protection activate, PIN 1234 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
9.9.3 Save user settings restore with PIN 9090 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
9.9.4 Sensor Alarm ON / OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
9.9.5 Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
9.9.6 Minimum speed cut off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
9.9.7 Reverse action of the control function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
9.9.8 Controller configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
9.9.9 Group control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Operating Instructions Fcontrol – model series FXDM25/32AM
L-BAL-E212-GB 1451 Index 003 Part.-No.
3/123

9.9.9.1 Group version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
9.9.9.2 Group variant 0: One controlled group and up to three switched groups . 61
9.9.9.3 Group version 1: Two controlled groups . . . . . . . . . . . . . . . . . . . . . . . 63
9.9.10 Display text for external message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
9.9.11 Offset control signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
9.9.12 Selection amplifier (comparator) control circuit 1 or 2 at output U, V, W . . . . . . . . . 65
9.9.13 Data on the total control deviation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
9.10 IO Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
9.10.1 Analog-Output “A” ............................................... 66
9.10.2 Digital inputs “D1” / “D2” ......................................... 67
9.10.2.1 Menu overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.10.2.2 Enable ON/OFF function
| 1D | . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
9.10.2.3 External fault Function
| 2D | ............................... 70
9.10.2.4 Limit ON / OFF, Function
| 3D | . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9.10.2.5 Switch over Input signal “E1” / “E2”, Function
| 4D | . . . . . . . . . . . . . . . 71
9.10.2.6 Set 1/2 or Setpoint 1/2, Function | 5D | . . . . . . . . . . . . . . . . . . . . . . . . 71
9.10.2.7 Intern / Extern Function
| 6D | .............................. 72
9.10.2.8 Automatic control / speed manual Function
| 7D | (mode 2.01 ) . . . . . . . 72
9.10.2.9 Reverse action of control function ( 2.01 ), Function
| 8D | . . . . . . . . . . . 73
9.10.2.10 Switch over Setpoint 1/2 for control circuit 2
| 9D | . . . . . . . . . . . . . . . . 73
9.10.2.11 Reset, Function
| 10D | ................................... 74
9.10.2.12 Setting Max. Speed ON / OFF function
| 11D | . . . . . . . . . . . . . . . . . . . 74
9.10.2.13 Motorheating ON / OFF, Function
| 12D | . . . . . . . . . . . . . . . . . . . . . . . 75
9.10.2.14 Direction of rotation, Function | 13D | . . . . . . . . . . . . . . . . . . . . . . . . . 75
9.10.2.15 “Freeze function” maintain momentary modulation value, Function
| 14D |
76
9.10.2.16 Switch over Setpoint 1/2 and Pband 1/ 2 for control circuit 1
| 15D | . . . . 76
9.10.2.17 Switch over Setpoint 1/2 and Pband 1/2 for control circuit 2
| 16D | . . . . 76
9.10.2.18 Timer function overwrite
| 21D | . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
9.10.3 Configuration of analog inputs “E1”and “E2” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
9.10.3.1 Signal adaption E1 and E2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
9.10.3.2 Inverting analog inputs “E1” / “E2” . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
9.10.3.3 “E1” / “E2” Bus mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
9.10.4 Function and inverting for relay outputs “K1” and “K2” . . . . . . . . . . . . . . . . . . . . . . 81
9.10.5 Programming Add-on module type Z-Modul-B . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
9.10.6 COM2 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
9.11 Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
9.11.1 Limit indication depending on modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
9.11.2 Limit indication depending on setting or sensor signal . . . . . . . . . . . . . . . . . . . . . . 86
9.11.3 Limit indication depending on (offset) to Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . 87
9.12 Motor Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
9.12.1 Setting motor rated current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
9.12.2 Setting motor rated voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
9.12.3 Adjustment of the U/f curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
9.12.4 Setting for Rampup time and Rampdown time . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
9.12.5 Setting Rolling direct. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
9.12.6 Setting Current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
9.12.7 Setting brake function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
9.12.8 Boost function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
9.12.9 Suppression of speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
9.13 Timer (Time switch clock) option with Z-Modul-RTC . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
9.13.1 Timerfunction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
9.13.2 Setting of time and date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
9.13.3 Automatic summer time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
9.13.4 Enter switching times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
9.13.5 Inverting timer function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
9.13.6 Overwrite timer function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
9.13.7 Adjustment of the real time clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Operating Instructions Fcontrol – model series FXDM25/32AM
L-BAL-E212-GB 1451 Index 003 Part.-No.
4/123

10 Menu tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
10.1 Menues of operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
10.2 Possible allocation of the IOs, PINs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
11 Diagnostics menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
11.1 Current measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
12 Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
12.1 Display and query of events and malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
12.2 Messages and trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
13 Function extension and version of software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
14 Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
14.1 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
14.1.1 Max. load dependent on ambient temperature and line voltage. . . . . . . . . . . . . . . . 119
14.2 Spare parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
14.3 Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
14.3.1 Connection suggestion for several motors with motor protection unit type STDT . . . . 120
14.3.2 Connection suggestion for Bypass with necessary time delay . . . . . . . . . . . . . . . . 121
14.4 Dimensions [mm] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
14.5 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
14.6 Manufacturer reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
14.7 Service information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Operating Instructions Fcontrol – model series FXDM25/32AM
L-BAL-E212-GB 1451 Index 003 Part.-No.
5/123

1 General notes
1.1 Structure of the operating instructions
Before installation and start-up, read this manual carefully to ensure correct use!
We emphasize that these operating instructions apply to specific units only, and are in no way
valid for the complete system!
Use these operating instructions to work safely with and on the device. They contain safety instruc-
tions that must be complied with as well as information that is required for failure-free operation of the
device.
Keep these operating insturctions together with the device. It must be ensured that all persons that
are to work on the device can refer to the operating instructions at any time.
Keep the operating instructions for continued use. They must be passed-on to all successive owners,
users and final customers.
1.2 Target group
The operating instructions address persons entrusted with planning, installation, commissioning and
maintenance and servicing and who have the corresponding qualifications and skills for their job.
1.3 Exclusion of liability
Concurrence between the contents of these operating instructions and the described hardware and
software in the device has been examined. It is still possible that non-compliances exist; no guarantee
is assumed for complete conformity. To allow for future developments, construction methods and
technical data given are subject to alteration. We do not accept any liability for possible errors or
omissions in the information contained in data, illustrations or drawings provided.
ZIEHL-ABEGG SE is not liable for damage due to misuse, incorrect use, improper use or as a
consequence of unauthorized repairs or modifications.
1.4 Copyright
These operating instructions contain copyright protected information. The operating instructions may
be neither completely nor partially photocopied, reproduced, translated or put on data medium without
previous explicit consent from ZIEHL-ABEGG SE. Infringements are liable for damages. All rights
reserved, including those that arise through patent issue or registration on a utility model.
2 Safety instructions
This chapter contains instructions to prevent personal injury and property damage. These instructions
do not lay claim to completeness. In case of questions and problems, please consult our company
technicians.
2.1 Intended use
The equipment is to be used solely for the purposes specified and confirmed in the order. Other uses
which do not coincide with, or which exceed those specified will be deemed unauthorised unless
contractually agreed. Damages resulting from such unauthorised uses will not be the liability of the
manufacturer. The user will assume sole liability.
Reading these operating instructions and complying with all contained instructions - especially the
safety notifications contained therein - are considered part of intended use. To consider is also the
manual of attached components. Not the manufacturer, rather the operator of the device is liable for
any personal harm or material damage arising from non-intended use!
2.2 Explanations of symbols
Safety instructions are highlighted with warning triangles and are depicted according to the degree of
hazard as follows.
Attention!
General hazardous area. Death or severe injury or significant property damage can occur if the
corresponding precautions are not taken!
Operating Instructions Fcontrol – model series FXDM25/32AM General notes
L-BAL-E212-GB 1451 Index 003 Part.-No.
6/123

Danger due to electric current
Danger by dangerous, electric voltage! Death or severe injury can occur if the corresponding
precautions are not taken!
Information
Important additional information and advice for user.
2.3 Product safety
The device conforms to the state of the art at the time of delivery and is fundamentally considered to
be reliable. The device and its accessories must only be used in a flawless condition and installed and
operated in compliance with the assembly instructions and/or operating instructions. Operating out-
side the device's technical specifications (
name plate and attachment / technical data) can lead to
a defect in the device and additional damage!
In the case of a malfunction or a failure of the equipment check all functions with alarms in
order to prevent injury to persons or property. Note possibility of back-up operation. If used in
intensive animal environments, any malfunctions in the air supply must be detected as soon
as possible to prevent the development of a life-threatening situation for the animals. The
design and installation of the system must comply with local regulations and directives. In
Germany these include DIN VDE 0100, the animal protection and the keeping of working
animals ordinance and the pig-keeping ordinance etc. Also note the instructions of AEL, DLG,
VdS.
2.4 Requirements placed on the personnel / due diligence
Persons entrusted with the planning, installation, commissioning and maintenance and servicing in
connection with the frequency inverter must have the corresponding qualifications and skills for these
jobs.
In addition, they must be knowledgeable about the safety regulations, EU directives, rules for the
prevention of accidents and the corresponding national as well as regional and in-house regulations.
Personnel to be trained or instructed and apprentices are only permitted to work on the device under
the supervision of an experienced person. This also applies to personnel undergoing general training.
Comply with the legal minimum age.
This device is not intended to be used by people (including children) who have restricted mental,
sensory or intellectual abilities or who have a lack of experience and/or knowledge.
2.5 Start-up and during operation
Attention!
•During commissioning, unexpected and hazardous conditions can arise in the entire installation
due to defective adjustments, defective components or incorrect electrical connections. Remove all
persons and objects from the hazardous area.
•During operation, the device must be closed or installed in a control cabinet. Fuses may only be
replaced by new ones and must not be repaired or bypassed. The data for the maximum line fuse
are to be considered absolutely (
Technical data). Use only fuses specified in schematic dia-
grams.
•Any faults detected in the electric system/modules/operating equipment must be corrected immedi-
ately. If these faults are not corrected, the device/system is potentially very dangerous. The
device/system must therefore not be operated when it is faulty.
•Pay attention to smooth, low vibration running of the motor/fan, the appropriate instructions in the
drive documentation must be observed!
Operating Instructions Fcontrol – model series FXDM25/32AM Safety instructions
L-BAL-E212-GB 1451 Index 003 Part.-No.
7/123

2.6 Working on device / Hazards through “residual voltage”
Information
Mounting, electrical connection, and start-up operation may only be carried out by an electrical
specialist in accordance with electrotechnical regulations (e.g. EN 50110 or EN 60204)!
Danger due to electric current
•It is generally forbidden to carry out work on electrical live parts. Protection class of the device
when open is IP00! It is possible to touch hazardous voltages directly.
•The safe isolation from the supply must be checked using a two-pole voltage detector.
•Even after disconnecting the mains voltage, life-threatening charges can appear between the
protective ground “PE” and the mains connection.
•The protective earth is conducting high discharge currents (dependent on the switching frequency,
current-source voltage and motor capacity). Earthing in compliance with EN specifications shall
therefore be observed even for testing and trial conditions (EN 50 178, Art. 5.2.11). Without
earthing, dangerous voltages can be present on the motor housing.
Waiting period at least 3 minutes!
Through use of capacitors, danger of death exists even after switching off the device through directly
touching the energized parts or due to parts that have become energized due to faults.
It is only permitted to remove the housing cover after waiting for 3 minutes once the line supply cable
has been shut down. Should measurement or adjustment work be unavoidable on the opened unit
while still powered, then this may only be performed by qualified personnel acquainted with the
thereby associated hazards.
Attention!
Automatically restart after a power failure or mains disconnection!
2.7 Modifications / interventions in the device
Attention!
For reasons of safety, no unauthorized interventions or modifications may be made on the device. All
planned modifications must be authorized by the manufacturer in writing.
Use only genuine spare parts / genuine wearing parts / genuine accessories from ZIEHL-ABEGG.Th-
ese parts were specifically designed for the device. There is no guarantee that parts from non-original
sources are designed and manufactured in correspondence with load and safety requirements.
Parts and optional equipment not supplied by ZIEHL-ABEGG are not approved by ZIEHL-ABEGG for
use.
2.8 Operator’s obligation of diligence
•The contractor or owner must also ensure that the electric systems and equipment are operated
and maintained in accordance with electro-technical regulations.
•The owner is obliged to ensure that the device is operated in perfect working order only.
•The device may only be used as intended (
“Application”).
•You must periodically examine the safety equipment for their properly functioning condition.
•The assembly instructions and/or operating instructions are always readily available at the location
where the device is being used, are complete and are in legible condition.
•These persons are regularly instructed in all applicable questions regarding occupational safety
and environmental protection and are knowledgeable regarding the assembly instructions and/or
operating instructions and, especially, are familiar with the safety instructions contained therein.
•All safety and warning notices attached to the device are never removed and remain legible.
Operating Instructions Fcontrol – model series FXDM25/32AM Safety instructions
L-BAL-E212-GB 1451 Index 003 Part.-No.
8/123

2.9 Employment of external personnel
Maintenance and service work are frequently carried out by external employees who often do not
recognize the specific situations and the thus resulting dangers.These persons must be comprehen-
sively informed about the hazards in their area of activity.
You must monitor their working methods in order to intervene in good time if necessary.
3 Product overview
3.1 Operational area
The frequency inverter is designed for a stepless control of fans without additional (electromagnetic)
motor noise.
Only suitable for drives with low set-off torque (e.g.: fans or pumps).
3.2 Functional description
The frequency inverters of these series generate their 3~ output with variable voltage and frequency
from the three-phase mains on the input.
The devices are constructed in accordance with the general requirement in EN 61800-2 for Adjustable
speed electrical power systems and is intended for one-quadrantdrives.
Information
By using the integrated all-pole effective Sine filter (phase to phase and phase to ground), an absolute
parallel control of fans without risk of damage for motors is possible. Screened motor cables are not
required!
3.3 Maintenance
The device must be checked for soiling and, if necessary, cleaned in periodic intervals.
The ventilation grilles on the bottom and on the top of the device must be free to ensure adequate
cooling of the device. They can be cleaned with a vacuum cleaner, broom or brush.
3.4 Transport
•The device is packed ex factory to suit the transport method previously agreed.
•Always use the original packaging materials when transporting the device.
•Avoid shocks and impacts to the device during the transport.
•During manual handling the human lifting and carrying restrictions must be observed and adhered
to.
3.5 Storage
•The device must be stored in its original packaging in a dry and weather-proof room.
•Avoid exposure to extreme heat and cold.
•Avoid prolonged storage; we recommend a maximum of one year (consult the manufacturer before
starting if stored for longer).
3.6 Disposal / recycling
Disposal must be carried out professionally and environmentally friendly in accordance with the legal
stipulations.
Operating Instructions Fcontrol – model series FXDM25/32AM Product overview
L-BAL-E212-GB 1451 Index 003 Part.-No.
9/123

4 Mounting
4.1 General notes
Attention!
The following points must be complied with during the mechanical installation to avoid causing a defect
in the device due to assembly errors or environmental influences:
•Before installation remove the device from the packing and check for any possible shipping
damage!
•Assemble the device on a clean and stable base. Do not distort during assembly! Use the
appropriate mounting devices for proper installation of the unit!
•A mounting on vibrating base is not permissible, if no data to the vibration strength is made (
Technical data)!
•When mounted onto lightweight walls, there must be no impermissibly high vibrations or shock
loads. Any banging shut of doors that are integrated into these lightweight walls, can result in
extremely high shock loads. Therefore, we advise you to decouple the devices from the wall.
•Do not allow drilling chips, screws and other foreign bodies to reach the device interior!
•Maintain the stated minimum clearances to ensure unobstructed cooling- air feed as well as
unobstructed outgoing air discharge (
minimum space requirement)!
•The device should be installed in a location where it will not be disturbed, but at the same time can
be easily accessed!
•Care must be taken to avoid direct radiation from the sun!
•The device is designed for vertical installation (cable inlet down). A horizontal or reclined installation
is only permissible after technical release of the manufacturer!
•Be sure to observe proper heat dissipation (
Technical data, heat dissipation).
4.2 Minimum space requirement
In order to ensure sufficient ventilation of the device, clearance on all sides of at least 50 mm has to
be maintained to the housing walls, switch cabinet doors, wiring ducts, etc. The same clearance
applies to the installation of several devices next to each other.
When installing several devices on top of each other, the danger of reciprocal heating exists. This
layout is only then permissible when the air suctioned from the upper unit does not become warmer
than the permissible ambient temperature (
Technical data). I.e., a correspondingly larger clearance
or thermal shielding is required.
Operating Instructions Fcontrol – model series FXDM25/32AM Mounting
L-BAL-E212-GB 1451 Index 003 Part.-No.
10/123

4.3 Prerequisites for mounting
1. Mark the four mounting points on the surface with the drilling template located on the box of the
device (Dimensions
Enclosure).
2. Remove the cover from terminal compartment.
3. Make holes and assemble the device depending on the surface with appropirate fixing material.
Operating Instructions Fcontrol – model series FXDM25/32AM Mounting
L-BAL-E212-GB 1451 Index 003 Part.-No.
11/123

4. All 6 cable entry points are in a sealed condition at delivery. Remove plastic fastener depending
on the need and insert appropriate cable glands (not in scope of delivery). The manufacturer's
specifications for tightening torque and sealing area must be observed! Entry points that are not
used must remain sealed!
5. Insert cables properly and ensure tightness of the cable glands.
6. Attach the cover of terminal compartment again carefully after connection (
Electrical Installa-
tion).
Tightening torque of the lid screws: 2 Nm
7. Install enclosed ventilation grid at the top of the unit.
4.4 Outdoor installation
Outdoor installation is possible up to -20 °C when the controller supply is not switched off. Installation
must be protected from the effects of weather as much as possible, including protection from direct
sunlight!
4.5 Installation location for agriculture
In order to avoid damage caused by ammoniac vapours, the controller shall not be installed in the
stable, but rather in an outhouse wherever possible.
4.6 Temperature influences during commissioning
Avoid condensation in the controller and functional faults attributable to condensation by storing the
controller at room temperature!
Operating Instructions Fcontrol – model series FXDM25/32AM Mounting
L-BAL-E212-GB 1451 Index 003 Part.-No.
12/123

5 Electrical installation
5.1 Safety precautions
Danger due to electric current
•Work on electric components may only be carried out by trained electricians or by persons
instructed in electricity under the supervision of an electrician in accordance with electrical engi-
neering regulations.
•The 5 electrical safety rules must be observed!
•It is forbidden to carry out work on electrically live parts. Even after disconnection, the dc-link is still
live. Always wait at least 3 minutes.
•Other measures may be necessary to achieve safe electrical isolation.
•A second person must always be present when working on energized parts or lines who discon-
nects in case of emergency.
•Only connect the motor to electrical circuits that can be disconnected with an all-pole isolating
switch.
•Inspect electrical equipment periodically: retighten loose connections – immediately replace dam-
aged lines and cables.
•Always keep switch cabinets and all electrical supply facilities locked. Access is only allowed for
authorized persons using a key or special tool.
•Operating the device with the housing cover removed is prohibited because energized, exposed
parts are present inside the device. Disregarding this regulation can lead to severe personal injury.
•The required protective earth connection is established using screws between the housing parts in
metal terminal space covers and housing casings. Commissioning is only permissible after these
screws have been properly attached!
•The device owner is responsible for the EMC of the entire plant according to the locally applicable
standards.
•Metal screwed-connections are not permitted in plastic housing parts because there is no potential
equalization.
•Never clean electrical equipment with water or similar liquids.
Information
The respective connections are represented in the enclosure of this manual ( Connection diagram)!
Operating Instructions Fcontrol – model series FXDM25/32AM Electrical installation
L-BAL-E212-GB 1451 Index 003 Part.-No.
13/123

5.2 Terminal compartment
Tightening torque protective earth connection (M5 Kombitorx): 4 Nm
1 Line
2 Motor
3 Control
4 Indication relays
5 MODBUS
5.3 EMC-compatible installation
5.3.1 Motor cable
The applicable standard for interference emissions is EN 61000-6-3. Compliance with this standard is
achieved through the use of an unscreened motor feed cable.
5.3.2 Control cables
Pay attention to sufficient distance from powerlines and motor wires to prevent interferences. The
control cable may not be longer than 30 m. Screened control cables must be used when the cable
length is longer than 20 m. When using a shielded cable connect the shielding to one side only, i.e.
only to the control unit with the protective ground (keep cable short and with as little inductance as
possible!).
5.3.3 Harmonics current and line impedance for devices > 16 A and ≤ 75 A
Extract from EN 61000-3-12, valid for equipments with rated current > 16 A and ≤ 75 A, connected to
public low-voltage systems.
This equipment complies with IEC 61000-3-12 provided that the short-circuit power S
SC
is greater than or equal
to R
SCE
x S
equ
at the interface point between the user's supply and the public system.
It is the responsibility of the installer or user of the equipment to ensure, by consultation with the distribution
network operator if necessary, that the equipment is connected only to a supply with a short-circuit power S
SC
greater than or equal to R
SCE
x S
equ
.
S
SC
Short-circuit power from line at the interface point between the user's supply and the public system
S
equ
Rated - apparent power for three phase devices: S
equ
√3 x U
I
x I
equ
(U
I
phase to phase voltage Technical data “Line voltage”)
(I
equ
rated current of the device Technical data “Rated current input”)
R
SCE
Short-circuit ratio
For this devices: R
SCE
≥ 120
Operating Instructions Fcontrol – model series FXDM25/32AM Electrical installation
L-BAL-E212-GB 1451 Index 003 Part.-No.
14/123

5.4 Mains connection
5.4.1 Line voltage
Power from the mains is connected to terminals: PE, L1, L2, L3. Here, it must be strictly observed that
the mains voltage lies within the allowable tolerance specifications (
Technical data and nameplate
affixed to the side).
Danger due to electric current
Not suitable for IT system!
5.4.2 Required quality attributes for the mains voltage
Danger due to electric current
The mains voltage must comply with the EN 50160 quality characteristics and the defined standard
voltages in IEC 60038!
5.4.3 Leakage current, securely attached, ground wire double up to 10 mm²
Danger due to electric current
In accordance with the defined networks in EN 60990 the device has a leakage current > 3.5 mA
so it must be permanantly connected. The protective ground must be made double in accord-
ance with EN 50178 Point 5.2.11and 5.3.2.1 up to a cross section of at least 10 mm².
5.5 Residual-current-operated protective device
Danger due to electric current
For an installation of r.c.d. protection, it shall be observed that this must be of “universal-
current sensitivity” (Type B). In accordance with EN 50 178, Section. 5.2. other types of current-
operated protective devices may not be used. To ensure as high a degree of reliability as
possible , we recommend a tripping current of 300 mA.
5.6 Inverter output
5.6.1 Motor connection
The motor leads are connected to the terminals: PE, U, V, W. Several fans can be connected to the
controller-the maximum total current of all motors must not exceed the current rating for the controller.
Information
•It is recommended that a separate motor protection unit be foreseen for each fan.
•For motors with thermistors “TP” (PTC thermistor) e.g. type U-EK230E
•For motors with thermostats “TB” (thermal contacts) e.g. type STDT16 or AWE-SK (
Enclosure:
Circuit suggestion for several motors with motor protection unit type STDT.)
5.6.2 Disconnection between controller and motor (repair switch)
Ideally, a repair switch should be installed before the controller (supply line disconnect).
In the case of complete disconnection (entire load) after the controller, the enable (controller OFF /
ON) must be disconnected simultaneously. I.e., an additional control contact is needed. Switching on
the motor while simultaneously issuing the enable (ON) achieves secure energizing with low satura-
tion of the controller. For this a programming is necessary (
IO Setup Enable ON / OFF).
Attention!
When switching on the motor plus existing release: under certain circumstances, this can occur under
full modulation of the controller.
Operating Instructions Fcontrol – model series FXDM25/32AM Electrical installation
L-BAL-E212-GB 1451 Index 003 Part.-No.
15/123

5.7 Motor protection
Motor protection is possible by connecting thermostats “TB” or thermistors (PTC thermistor) “TP”.
•When connecting several motors, always make sure that thremostats “TB” or thermistors “TP” are
connected in series. A maximum of six individual thermistors (DIN 44081 or DIN 44082) may be
connected in series to a single device. At least two or three single thermistors are installed depend-
ing on the motor type.
•Monitoring of motors in Ex zones is not permissible. For systems of this type, an additional posistor
tripping unit is required, with disconnection via a separate motor protection circuit.
The unit switches off when a connected thermostat or thermistor has tripped the circuit (interruption
between both terminals “TB/TP”. The unit then remains switched off. A programmed fault-indicating
relay is triggering.
Display during motor fault
Possibilities for re-starting after the drive has cooled down terminals “TB/TP” bridged by:
•By switching the mains voltage off and then on again.
•Function “Reset” Menu group “Start”
•By digital input for remote (enable ON/OFF) or by Reset-input (
IO Setup - Digital Inputs).
Attention!
•An outside voltage may never be connected to the terminals “TB/TP” and/or!
•If a bypass circuit is installed, or in the “100 %” position on devices with a main switch, the motor
protection inside the controller has no function. In this case, additional motor monitoring may be
required.
5.8 Signal input or sensor connection (E1, E2)
The unit has two analog inputs: Analog In 1 “E1” and Analog In 2 “E2”
The connection is independent of the programmed operating mode and from the sensor signal
employed.
•When connecting passive temperature sensorsTF.. (KTY81-210) or PT1000 at terminals “E1” and
“T” or “E2” und “T” must be paid attention to no polarity.
For a high interference immunity a capacitor must be connected directly to the sensor (1 nF
parallel). With temperature sensors type TF.. (KTY81-210) a capacitor is integrated.
•When connecting aktive sensors at the terminals “E1” and “GND” or “E2” and “GND” attention must
be paid to correct polarity, a 24 V DC power supply is integrated.
• For sensors in two-wire-technology (4 - 20 mA signal), the connection is made on the “E1” and
“24 V” or “E2” and “24 V”, “GND” terminal is omitted.
Danger due to electric current
Never apply line voltage to analog inputs!
5.9 Analog output (0 - 10 V) “A1”
The analogoutputs 0 - 10 V can be allocated with various functions (
IO Setup: Analog output “A”).
Connection to terminal “A” - “GND” “Analog Out” (I
max
technical data / connection diagram).
It is not permissible to connect outputs of several devices to each other!
5.10 Voltage supply for external devices (+24V, GND)
A voltage supply is integrated for external devices e. g. a sensor (max. current load
technical data).
In case of overload or short circuit (24 V – GND), the external power supply is shut down (multi-fuse).
The device performs a “Reset” and continues operation.
It is not permissible to connect outputs of several devices to each other!
Operating Instructions Fcontrol – model series FXDM25/32AM Electrical installation
L-BAL-E212-GB 1451 Index 003 Part.-No.
16/123

5.11 Add-on module type Z-Modul-B Part-No. 380052
The add-on module can be retrofitted as required. This may be necessary when the analog and digital
outputs and inputs are insufficient for certain applications. The board is easy to install in the device
and is connected to the printed circuit board (X13) with the plug. The additional outputs and inputs are
programmed in the menu group “IO Extension”, this appears automatically after the menu group “IO
Setup”if an add-on module is installed.
Information
The clock module type Z-Module-RTC and the add-on module type Z-MODULE-B both need the slot
| X13 | . That means that only one of the two modules can be used!
Add-on module type Z-
Modul-B
•1x analogue input 0-10 V (R
i
> 100 kΩ) for external Set point
•1x output 0 - 10 V (I
max
10 mA)
•3x digital-inputs, Activation via floating contacts
•2x relay outputs (contact load 2 A 250 V AC)
5.12 Digital inputs (D1, D2)
Various functions can be allocated to the digital inputs “D1”and “D2” (
IO Setup: Functions summary
of the digital inputs). Activation via floating contacts (a low voltage of ca. 24 V DC is connected).
Danger due to electric current
Never apply line voltage to the digital input!
Observe input resistance and voltage range (
Technical data).
5.13 Relay outputs (K1, K2)
Various functions can be allocated to the relay outputs “K1” and “K2” (
IO Setup: function and
inverting relais outputs). Max. contact rating
technical data and connection diagram.
Relays K1
•Connection of the floating contacts of relay “K1” to the terminals 11, 14, 12.
•“K1 Function” factory setting:
| 1K | Operating indication. I.e. energized for operation without
fault, for enable “OFF” de-energized.
Relays K2
•Connection of the floating contacts of relay “K2” to the terminals 21, 24, 22.
•“K2 Function” factory setting:
| 2K | Fault indication. I.e. energized for operation without fault and
for enable “OFF”.
Operating Instructions Fcontrol – model series FXDM25/32AM Electrical installation
L-BAL-E212-GB 1451 Index 003 Part.-No.
17/123

5.14 Communication
5.14.1 RS-485 interface for MODBUS
The device comes equipped with a RS-485 interface for networking via MODBUS. Conntection at: “A
(D+)”, “B (D-)” and “GND”.
11.03.2014
v_am_modbus_connect.vsd
ID1 GND A
(D+)
B
(D-) ID2GND A (D+)
B
(D-)
B
(D-) ID1 GND A (D+)
B
(D-) ID2GND A (D+)
MODBUS
(RS-485)
MODBUS
(RS-485)
Addressing Addressing
MODBUS
(RS-485)
MODBUS
(RS-485)
Addressing Addressing
The connections for MODBUS “A (D+)”, “B (D-)” are available double and are connected with each other internally.
Information
•You must ensure correct connection; i.e. “A (D+)” must also be connected on the following devices
to “A (D+)”. The same applies to “B (D-)”.
•In addition, a "GND" connection must be established, as dissimilar potential (over 10 V!) will lead to
the destruction of the RS-485 interface (e.g. lightning).
•Except the data link “A (D+)”, “B (D-)” and “GND” (for automatic addressing additional “ID1” - “ID2”
following chapter) no further cable cores of the data line may be used.
•Do not use wire shield.
•Pay attention to sufficient distance from powerlines and motor wires (min. 20 cm).
•A maximum of 64 members can be directly connected to one another, and another 63 members via
a repeater (only for manual addressing i.e. no connection of the terminals “ID1”,“ID2”).
Example for MODBUS connection
MODBUS
26.02.2007
v_modbus_verbindung.vsd
The data line must be conducted from one device to the
next. No other type of wiring is allowed!
Always use only two wires of one lead (twisted pair) for
the connection.
Recommended wire types
1. CAT5 / CAT7 cables
2. J-Y (St) 2x2x0.6 (telephone wire)
3. AWG22 (2x2 twisted pair)
Max allowed wire length 1000 m (CAT5/7 500 m).
When using telephone flex with four cable cores, we recommend the following allocation:
•A (D+) red
•B (D-) black
•ID1 - ID2 yellow (for automatic addressing)
•GND white
Default interface parameter
•Baudrate 19200
•Bits 8
•Parity Even
•Stop bits 1
•Handshake none
Operating Instructions Fcontrol – model series FXDM25/32AM Electrical installation
L-BAL-E212-GB 1451 Index 003 Part.-No.
18/123

Information
•Addressing is performed by an external terminal or a PC with the appropriate software (automatic
addressing
following chapter).
•The MODBUS register description and the information sheet “Network structure of MODBUS” can
be requested from our Support Department V-STE for control systems - ventilation.
5.14.2 Automatic addressing
Automatic addressing can be performed by a PC with ZAset software. The connections “ID1” and
“ID2” for “addressing” are connected with each other additionally next to the bus connection for this.
This means that it is no longer necessary to address every single member manually in the network.
On the first client that is connected directly to the terminal or the PC, “GND” and “ID1” or “ID2” must be
bridged. This is recognised as a result and occupied by address 1.
For the following clients the connection “ID1” or “ID2” of a client respectively is connected with
connection “ID1” or “ID2” of the next client.
The automatic addressing of other clients is initiated by the previous client via this connection.
Example for automatic addressing via USB converter
11.11.2013
v_modbus_autoadr_zaset.vsd
ID1 GND A
(D+)
B
(D-) ID2
MODBUS
(RS-485)
Addressing Addressing
ID1 GND A
(D+)
B
(D-) ID2
MODBUS
(RS-485)
Addressing Addressing
A
(D+)
B
(D-)
GND (X) USB
USB-485-Mini/OP
On the USB-485 converter connection to the terminals: A (D+), B (D-) and GND.
Connection of the clients via the terminals: A (D+), B (D-), GND and ID1 / ID2
Information
•Except the data link “A (D+)”, “B (D-)” the “ID1 - ID2” and the “GND” connection may no further cable
cores of the data line be used.
•The connections for the automatic addressing “ID1” and “ID2” are not directly connected with each
other internally. These may not be bridged; any order of connection is possible.
•When using the automatic addressing, no repeaters can be used because these do not pass the
signal through to the addressing.
Operating Instructions Fcontrol – model series FXDM25/32AM Electrical installation
L-BAL-E212-GB 1451 Index 003 Part.-No.
19/123

5.15 USB-interface
Over the USB interface if necessary a software update can be made. For this a consultation with our
V-STE support department for control systems-ventilation technology is necessary.
For communication with a PC (Virtual COMM Port) we make the necessary programs available on
request.
Danger due to electric current
Plug the jumper J1 to both PINs only for a software update via USB interface. The device will not
switch on if this jumper is plugged to both PINs!
Do not replug the jumper under voltage, observe the safety instructions!
5.16 Potential at control voltage connections
The control voltage connections (< 50 V) relate to the joint GND potential (Exception: Relay contacts
are potential free). There is a potential separation between the control voltage connections and the
protective earth. It must be ensured that the maximum external voltage at the control voltage
connections cannot exceed 50 V (between “GND” terminals and “PE” protective earth). If necessary, a
connection to the protective earth potential can be established, install bridge between “GND” terminal
and the “PE” connection (terminal for screening).
5.17 Bypass circuit
Please observe the following during bypass switching (controller shunt with mains voltage):
•Mutual locking of mains contactor and bypass protection
•Time delay of at least 1 second during switching
•The controller “enable” (ON / OFF) must be simultaneously opened together with cut-off of the
protection on the controller output; during connection it must be simultaneously closed again. For
this a programming is necessary (
IO Setup Enable ON / OFF).
•By switching OFF necessary waiting period before renewed switching on amounts minimum
90 seconds! (
connection suggestion for bypass with the required time-delay)
•Never apply line voltage to the inverter output!
5.18 Manual Bypass-Switch type S-D-25 and S-D-50
As accessories are manual main switches with bypass function available.
By switching OFF Frequency inverters necessary waiting period before renewed switching on
amounts minimum 90 seconds!
Switch position
•
| 0 | Switch OFF supply line (lockable)
•
| AUTO | Operation Control
•
| 100 % | Operation Bypass (controller without supply)
Technical data
•Line voltage max. 690 V, 50/60 Hz
•Rated current
–Type S-D-25 Part.-No. 349035: 25 A
–Type S-D-50 Part.-No. 349040: 50 A
•Dimensions w x h x d [mm]
–Type S-D-25: 115 x 115 x 163
–Type S-D-50: 135 x 135 x 188
•Protection class IP65
S-D-25
AUTO
0
100 %
3 ~ 400 V
Controller
S-D-25
04.12.2007
v_sd25.vsd
Manual Bypass-Switch type S-D-25 / S-D-50
Operating Instructions Fcontrol – model series FXDM25/32AM Electrical installation
L-BAL-E212-GB 1451 Index 003 Part.-No.
20/123