ZIGBEE OPS305 User manual

OPS305
Occupancy Sensor
Quick Start Guide

2
Safety Handling
WARNING: Failure to follow these safety notices could result in 󽘀re,
electric shock, other injuries, or damage to the Occupancy Sensor
and other property. Read all the safety notices below before using
the Occupancy Sensor.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit on your own.
• Do not expose the unit or its accessories to 󽘁ammable liquids, gases
or other explosives.

3
Technical Speci󽘀cations
Wireless Connectivity
ZigBee • 2.4GHz IEEE 802.15.4
ZigBee Pro󽘀le • ZigBee 3.0
RF Characteristics
• Operating frequency: 2.4GHz
• Range outdoor/indoor: 100m /
30m (Open area)
Physical Speci󽘀cations
Operating Voltage • Micro-USB
Detector • 10.525GHz Doppler Radar
Detection Range • Maximum radius: 3m
• Angle: 100° (±10° )
Hanging height • Maximum 3m
IP rate • IP54
Operating environment
• Temperature:-20 ℃ ~+55 ℃
• Humidity:
≤ 90% non-condensing
Dimension • 86(L) x 86(W) x 37(H) mm
Mounting Type • Ceiling

4
Welcome
1
OPS305 Occupancy Sensor can detect presence, even if you are asleep
or in a stationary posture. Presence detected via radar technology,
which is more sensitive and accurate than PIR detection. It can be
tremendously beneficial in nursing homes to monitor and link with
other devices to make your home smarter.
This guide will provide you with an overview of the product and help
you get through the initial setup to installation.
• ZigBee 3.0
• Discern presence, even if you are in a stationary posture
• More sensitive and accurate than PIR detection
• Extend the range and strengthen ZigBee network communication
• Suitable for both residential and commercial application
Features:

5
2Get to know your device
LED indicator
Micro-USB
Reset Button
Reset: Press and hold the reset button for 10 seconds until the LED
light 󽘁ashes three times at third second, and it will 󽘁ash three times in
the tenth second.
Reset Button

6
3Con󽘀gure Network
LED indicator
The LED status gives the following information of the occupancy
sensor:
LED Status What it means
No light Device has joined a ZigBee network.
Continuous and slow
󽘁ashing
Device has not joined a ZigBee network.
Flashing once Presence detected
When you press the reset button once
Flashing once Device has joined a ZigBee network.
Flashing three times Device has not joined a ZigBee network.
3.1 Before starting, you will need:
• A ZigBee Gateway.
3.2 Adding to the gateway's network：
Follow the steps below to join the occupancy sensor to the gateway's
network:
1. Power on the occupancy sensor, the LED indicator will start
continuous and slow flashing, which meas it is ready to join the
network. If not, please reset it.
2. Set your gateway to permit joining.
3. The occupancy sensor will join the gateway's network automatically
and the LED indicator will go out when successfully joined.

7
4Installaion
Important safety information!
• Do not touch the terminals of the device while testing.
• Turn o󽗿 all the power supply for this equipment before installing.
• Make sure that the power supply is off before connecting or
disconnecting it to an auxiliary device.
• Always use a properly rated voltage sensing device to con󽘀rm power
is o󽗿.
• Replace all devices, doors and covers before applying power to the
equipment.
1. The installation location should be far away from pets, ventilation
ducts, 󽘀re-󽘀ghting ducts, drainage ducts, mechanical vibration, large
metal equipment or places with vibrating and swinging objects,
because it will a󽗿ect the radar re󽘁ection and cause false alarm.

8
2. You need to pay attention to the distance and range of the
occupancy sensor when installing. Within the sensing range, avoid
facing another occupancy sensor or radar equipment.
󾙓󾙒󾙒󾙓󾙒

󾙕
󾙕
󾙕

9
3. Use the mounting bracket as template to mark the two holes on the
ceiling for installing screws.
4. Screw the mounting bracket onto the ceiling according to marked
location. Install wall plugs if necessary.
5. Locate the hooks of the mounting bracket and line up the hooks
with the mounting holes on occupancy sensor. Fit the hooks into the
mounting holes as the picture below. Installation is now completed.