Zinwell ZAT-600B User manual

Installation and Description Guide
Version 2.1.8
Copyright © 2023 Zinwell Corporation. All rights reserved.
Zinwell and the logo of Zinwell are the distinctive trademarks of Zinwell Corporation in R.O.C. (Republic of China) and/or other jurisdictions.
This product is under the protection of Taiwan, R.O.C. (Republic of China) and international copyright and intellectual property laws.
August 2023, Version 2.1.6
NextGen TV Box Model: ASTC 3.0 600B
NextGen TV Box
ZAT-600B

NextGen TV Box | Installation and Description Guide | 1
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.

NextGen TV Box | Installation and Description Guide | 2
Contents
Important Safety Instruction and Precaution __________________________________3
Knowing Your NextGen TV Box _______________________________________________4
Theory of Operation ______________________________________________________4
Model Specification ______________________________________________________4
Features _________________________________________________________________5
Package Contents ________________________________________________________5
Panel Specification _______________________________________________________5
Remote Control Overview _____________________________________________________6
Programming the Remote Control _____________________________________________7
Installing Your NextGen TV Box _______________________________________________8
Installing Instruction in 4 Steps ___________________________________________8
Setting up the Program System –First Time Installation _______________________9
Wi-Fi ON: Connecting to Internet via Your Wi-Fi/AP Router ___________________10
Wi-Fi OFF: Connecting to Internet via Ethernet Network _____________________12
Function Overview ___________________________________________________________13
Guide to the Setting System _____________________________________________14
Other Functions _________________________________________________________14
»Searching for the Available Channels (Auto Scan) ____________________14
»Searching for the Available Channels (Manual Scan) _________________14
»Selecting Your Preferred Language for Audio ________________________15
»Turning Off the Caption _____________________________________________15
»Selecting the Parental Rating _______________________________________15
»Time Settings ______________________________________________________16
»Setting the Display Duration _________________________________________16
»Changing the Administrator PIN _____________________________________16
»Obtaining the Program Content Introduction _________________________17
Software Upgrading via OTA Service _________________________________________18
APK Installation and Software Upgrading via USB Storage Device _____________20
Trouble Shooting ___________________________________________________________22
Contacting Us ______________________________________________________________ 23

NextGen TV Box | Installation and Description Guide | 3
Important Safety Instruction and
Precaution
Read through all the instructions carefully before use.
Operate this product only in the manner described.
Only a Water-dampened soft-cloth is recommended to clean the surface of this
product.
Do not expose this product excess vibration.
Keep this product in well ventilated areas.
The following substance or condition will cause the damage to this product:
»any liquid such as water or moisture
»extreme heat, cold, humidity
»dusty or sandy environments
During lightning storms, disconnect this product from electrical mains and
antenna.
Only place this device on stable surfaces and ensure that any attached cables
are secure and will not cause the device to fall.
There are no user serviceable parts in this product.
Any un-authorized attempt to disassemble or repair this product will void
product warranty and may cause dangerous electric shock.
Retain the manuals for future reference.
ONLY remove any power or data cords by pulling them from the plug.
Using this product near other electronic devices may cause interference.
Images shown in this document are for references only and there may be
differences between images and actual products.
Do not mix old and new batteries in the IR remote control.

NextGen TV Box | Installation and Description Guide | 4
Theory of Operation
Tuner Input
ATSC1.0/3.0 Dual Mode Tuner
01 Tuner
Frequency Range
42MHz ~ 866MHz
Video (optional)
Decode
MPEG2 (ATSC 1)
HEVC 4Kp60 (ATSC 3)
Output
HDMI 2.1
Audio (optional)
Decode
AC
-3 (ATSC 1)
AC
-4 (ATSC 3)
Output
HDMI 2.1
Ethernet
10/100M
RJ
-45
Wi
-Fi
2.4/5Ghz 1T1R
802.11n/ac
DC Power Adaptor
DC Jack
12V / 1.5A
Peripheral
USB 3.0
USB Type A
LED indicator
ON: White, Standby: Red
Remote Control
IR + Learning Type
34 Keys
(incl. 6 keys with learning function)
Dimension
160 x 75.8 x 34 (mm)
HDCP
HDCP 1.4, HDCP 2.2, HDCP 2.3
HDR
HDR
-10 and HLG: Ready; SL-HDR: Readiness to be discussed
Widevine
Level 1
Knowing Your NextGen TV Box
Model Specification
Coax Cable
HDMI
Antenna

NextGen TV Box | Installation and Description Guide | 5
Features
»Emergency alerting system
»ATSC 3.0 broadcast application compliant
»ATSC 3.0 / 1.0 receiving capability
»4k UHD Video
»Remote learning Application
Package Contents
Panel Specification
1. Antenna port is to connect the cable from your aerial
2. HDMI out port is to connect the cable from your display
3. LAN port is for Ethernet (RJ45) network or internet access
4. USB port is for peripherals such as thumb drive, storage devices and so on
5. DC IN is to connect the power adapter (12V/1.5A) to provide power to the
NextGen TV Box
NextGen TV Box X 1
Quick Start Guide X 1
Remote Control X 1
Power Adapter X 1
1 2 3 4 5

NextGen TV Box | Installation and Description Guide | 6
1 2
4
3
5
6
78
9
10
11 12
13 14
15
16
17
18 19
1. Power (Red Button): NextGen TV Box OFF/ON
2. TV Power : TV OFF/ON.
3. TV Mute: TV MUTE.
4. Audio: Select alternate audio
5. Closed Caption: Closed Caption Off/On
6. Yellow & Green Buttons: User defined.
(Program to TV functions using the learning
mode.)
7. Home: Return to live TV
8. Guide: Display the program guide
9. ▲▼◄ ►: Move the cursor or field in the
direction.
10. OK: Select highlighted screen options.
11. Back: Back to the previous page/channel.
12. Info: Display program info banner
13. TV VOL+, TV VOL–: TV volume Up/Down
14. CH+, CH–: Channel change Up/Down
15. ALERT: Emergency Alert
16. App: Launch NextGen Broadcast Application
(If available)
17. Numeric: Enter channel number or password.
18. Android Settings: Open Android Settings
19. Live TV Settings: Display Menu for Scan
Channels, Audio Language, Closed Caption,
Parental Rating, Time Settings, UI Settings &
Change PIN.
Remote Control Overview

NextGen TV Box | Installation and Description Guide | 7
Programming:
1. Press and hold the black ” TV POWER" button for 3
seconds until the red LED changes from flashing to solid.
The solid red LED indicates the remote control is in
learning mode.
2. Once in learning mode, press and release one of the six
learning keys to be programmed. The indicator light will
change from solid to slow flashing.
3. Point the front of the TV remote control at the front of the
Zinwell remote (about 1~2in). Then press and hold any
button on the TV remote control to be learned by the
Zinwell remote. After the signal is learned, the indicator
light will flash 3 times quickly then you can release the
button.
4. Press OK button of the Zinwell remote to save
programming.
** Repeat steps 2, 3 and 4 to learn other keys in the TV area.
Press OK button of the Zinwell remote to save programming.
NOTE:
1. During the learning process, if you wait for more
than 10 seconds at any time, it will automatically
exit the learning mode.
2. During the learning process, press any button
other than the six learning keys to exit the
learning mode.
3. Keep the two remote controls steady when
pointed at each other during the learning process.
Red LED Feedback:
1. Solid LED: Remote is in learning
mode, awaiting a key to be
selected for programming.
2. Slow Flashing LED: Remote is
awaiting from TV remote
control.
3. LED flashes 3 times: Learning
is successful.
The remote is capable of controlling up to six basic functions of most TVs and
audio devices (volume, mute, power, input). Use the instructions below for
programming the six designated learning keys to operate your TV or audio device.
Learning Keys:
TV Remote Control
about 1~2in
Programming the Remote Control

NextGen TV Box | Installation and Description Guide | 8
Installing Instruction in 4 Steps
Before Reading the Instructions:
Refer to the page 5 Panel Specification for the location of each port or button
mentioned below
STEP 1.
STEP 2.
STEP 3.
STEP 4.
Connect your Coaxial Cable to the Antenna Port.
Insert your HDMI cable from HD TV into HDMI OUT Port.
Plug the power adaptor into DC IN Port while the other end into
power socket.
For watching encrypted programs, it is necessary to connect to internet
in First Time Installation. Connect the Ethernet Cable to your Internet
access points from the Router, or through Wi-Fi by using the remote
controller to connect.
Installing Your NextGen TV Box

NextGen TV Box | Installation and Description Guide | 9
STEP 1.
Turn on the Power of NextGen TV
Box. Quick Setup page will be
shown as the image on the left side.
Press "OK"to confirm.
STEP 2.
Process of Channel Scanning will be
completed once the percentage bar
has reached 100%.
STEP 3.
"Service found"stands for available
TV channels during scanning.
Setting up the Program System –
First Time Installation
STEP 4.
After completion of Channel
Scanning, the program will start
displaying. Refer to the image on
the left side.
Note: For watching encrypted channels it is necessary to connect to the internet
either via Wi-Fi or Ethernet. Please refer to page 10 to 12 for connecting to the
internet.

NextGen TV Box | Installation and Description Guide | 10
STEP 1.
Turn on the Power of NextGen TV Box (IF
it’s the First Time Installation) ➞Press the
"SETTING" button (Android Setting Key) on
the remote controller (Refer to the Image
on the left side).
(IF Any) Ensure the Ethernet Cable is
DISCONNECTED to the NextGen TV Box.
Select "Network & Internet" ➞Press "OK"
on the remote control to confirm.
STEP 2.
Use Cursor Keys (▲▼◄ ►) on the remote
control to move to Wi-Fi ➞Press "OK"on
the remote control to ENABLE Wi-Fi.
A list of Available 2.4G Network will be
shown.
Use Cursor Keys (▲▼◄ ►) on the remote
control to move to your preferred Wi-Fi/AP
Router ➞Press "OK"to confirm. (Refer to
the image on the left side)
Wi-Fi ON: Connecting to Internet via
Your Wi-Fi/AP Router
Before Reading the Instructions:
The Wi-Fi and Ethernet functions CANNOT be executed at the same time. Ensure
the NextGen TV Box is NOT CONNECTED to any Ethernet Cable before ENABLING
Wi-Fi function in the NextGen TV Box.

NextGen TV Box | Installation and Description Guide | 11
STEP 3.
(IF Any) Use Cursor Keys (▲▼◄ ►) on the remote control to enter the
"PASSWORD" of your Wi-Fi/AP router (RD2_Lyra_Voice_2.4G here is as an
example) -> Use Cursor Keys (▲▼◄ ►) on the remote control and move to Done
for confirmation (Refer to the image above)
STEP 4.
When the connection is successful, the
status "Connected" will appear. (Refer to the
image on the left side)

NextGen TV Box | Installation and Description Guide | 12
STEP 1.
Press the "Android Setting" key on the
remote control ➞Select "Network & Internet"
➞Press "OK"on the remote control to
confirm.
STEP 2.
Connect your Ethernet (RJ45) cable to the
LAN port on your Broadband Set-Top-Box ➞
The system will automatically update the
network connection status. Refer to the
image on the left side.
Wi-Fi OFF: Connecting to Internet via
Ethernet Network
Before Reading the Instructions:
The Wi-Fi and Ethernet functions CANNOT be executed at the same time.
Ensure the NextGen TV Box is NOT CONNECTED to any Wi-Fi before
connecting to the Ethernet Cable.
Refer to the page 5 Panel Specification for the location of each port or button
mentioned below.

NextGen TV Box | Installation and Description Guide | 13
Function Overview
Home
Setting
Guide
Scan Channels
Audio Language
Closed Caption
UI Settings
Auto Scan
Manual Scan
Electronic Program Guide
Parental Rating
Time Setting
Change PIN

NextGen TV Box | Installation and Description Guide | 14
Guide to the Setting System
Press "MENU" (App Setting
Key) to enter the Setting
System. Refer to the image
on the left side.
Other Functions
Searching for the Available Channels (Auto Scan)
MENU (App Setting Key) ➞
Scan Channels ➞Mode:
Auto Scan ➞Press "Start" to
Scan.
MENU (App Setting Key) ➞
Scan Channels ➞Mode:
Manual Scan ➞Select
Channel Number ➞Press
"Start" to Scan.
Searching for the Available Channels (Manual Scan)

NextGen TV Box | Installation and Description Guide | 15
MENU (App Setting Key) ➞
Audio Language ➞Select
your prefer language ➞
Press "BACK" to confirm.
MENU (App Setting Key) ➞
Closed Captions ➞
Press "OK"to confirm.
MENU (App Setting Key) ➞
Parental Rating (The Admin
PIN MUST be ENTERED
before entering the Parental
Rating screen (The default
password is: 0000) ➞Select
the Rating Restriction ➞
Press "BACK" to confirm.
Selecting Your Preferred Language for Audio
Turning Off the Caption
Selecting the Parental Rating

NextGen TV Box | Installation and Description Guide | 16
MENU (App Setting Key) ➞
Time Settings ➞Select time
zone ➞Press "BACK" to
confirm.
MENU -> UI Settings -> Select
the Timeout -> Press "OK" to
confirm.
(Before entering the Change PIN
screen, the Admin PIN MUST be
ENTERED (the default password is:
0000)).
MENU (App Setting Key) ➞Change
PIN ➞Press "OK"and enter the
NEW Administrator PIN ➞Press "
OK"to confirm.
Time Settings
Setting the Display Duration of Mini EPG
Changing the Administrator PIN

NextGen TV Box | Installation and Description Guide | 17
Obtaining the Program Content Introduction
Press "Guide" on the remote control ➞Electronic Program Guide ➞Use Cursor
Keys (▲▼◄ ►) to select the different program blocks for getting the program
content introduction.

NextGen TV Box | Installation and Description Guide | 18
Software Upgrading via OTA Service
STEP 1.
Press SETTING button (Android Setting
Key) on the remote control ➞Select
" Apps" ➞Select "See All apps“.
The following screen will appear ➞
Select "Apps Download" to confirm.
STEP 2.
Use the remote control to select "Open" ➞
Press "OK" to confirm.

NextGen TV Box | Installation and Description Guide | 19
STEP 3.
Select "NextGenLiveTvLauncher 2.1.5" ➞press "OK"to confirm.
STEP 5.
Select "DONE" to complete the APK installation process.
STEP 4.
The installation screen is as below. Find the "INSTALL" button at the bottom right
corner of the screen ➞Press "OK"to install.