Zipato ZIPABOX-ZIGBEE-V1 User manual

DECLARATION OF CONFORMITY
Tri plus grupa d.o.o. declares that this product is in compliance
with the essential requirements and other relevant provisions of
Directives as follows:
Model: ZIPABOX-ZIGBEE-V1
Intented use: indoor
EMC Directive (2004/108/EC)
Low Voltage Directive (2006/95/EC)
R&TTE Directive (1999/5/EC)
The product is compatible with following norms/standards:
EN 60950-1:2007+A11:2009+A12:2011
EN 301 489-17 V2.1.1:2010
EN 301 489-3 V1..4.1:2003
EN 301 489-1 V1.8.1:2008
EN 300 328 V1.7.1:2008
EN 50130-4:1977+A1:2000+A2:2004
EN 300 220-1 V2.1.1:2006
EN 300 220-2 V2.1.2:2008
Manufacturer/Authorised representative,
Dean Janacek
Zagreb, 12 September 2012
ZigBee expansion module
Tri plus grupa d.o.o.
Banjavciceva 11
10000 Zagreb
Croatia

COMPATIBILITY
This expansion module is designed to work only with Zipabox.
HANDLING
Do not drop, knock or shake the module. Rough handling can break
internal circuit boards and connectors.
ENVIRONMENT
Do not expose the module to excessive heat or cold, as it can damage or
shorten the life of electronic circuit boards.
If possible, dispose this module at a recycling center. Do not dispose of
this module with the household waste.
SPECIFICATION
Power supply: from Zipabox
Operating temperature: -10° ~ +40° C
Operating humidity: 5 ~ 95% RH
Dimensions: 29 x 87 x 46 mm (without antenna)
Weight: 62g (with antenna)
Communication frequency: 2.4 GHz
Communication protocol: ZigBee
Communication range: up to 30m indoor or 70m outdoor
UNPACKING
ZigBee expansion module consists of:
1x expansion module
1x 2.4 GHz antenna
• Connect antenna by screwing it clockwise to the connector on the
module
CONNECTING DEVICE
1. Disconnect Zipabox from power;
2. Align connector of ZigBee expansion module to expansion Slot 2
of Zipabox (or to module connected into Slot 2);
3. Join module and Zipabox together until gap between them is
completely closed.
INSTALLATION/MOUNTING
Mount together with Zipabox.
INTERFERENCE
All wireless devices are subject to interference, which could affect device
performance.
REPARING
Do not attempt to repair this product. There are no user-serviceable parts
inside.
WATER-RESISTANCE
This product is not water-resistant. Keep it dry. Moisture will corrode the
inner electronics.
CLEANING
Use a dry cloth to clean this product. Do not use harsh chemicals, cleaning
solvents or strong detergents.
COPYRIGT
The contents of this manual is subject to copyright protection. Copying and
reproducing is prohibited without prior written permission. Information in
this document is subject to change without prior notice. Check
www.zipato.com for updates.

TESTING
1. Battery in Backup module comes charged
2. When Backup module is first time connected to Zipabox upper
LED is red indicating battery is discharging
3. When ZipaBox is connected back to power supply upper LED
will become green
4. When battery is charging lower LED is blue
REPARING & CLEANING
Do not attempt to repair this product. There are no user-serviceable parts
inside.
Use a dry cloth to clean this product. Do not use harsh chemicals,
cleaning solvents or strong detergents.
WATER-RESISTANCE
This product is not water-resistant. Keep it dry. Moisture will corrode the
inner electronics.
COPYRIGT
The contents of this manual is subject to copyright protection. Copying
and reproducing is prohibited without prior written permission. Information
in this document is subject to change without prior notice. Check
www.zipato.com for updates.
DECLARATION OF CONFORMITY
Tri plus grupa d.o.o. declares that this product is in
compliance with the essential requirements and other
relevant provisions of Directives as follows:
Model: ZIPABOX-POWER-V1
Intented use: indoor
EMC Directive (2004/108/EC)
Low Voltage Directive (2006/95/EC)
R&TTE Directive (1999/5/EC)
The product is compatible with following norms/standards:
EN 60950-1:2007+A11:2009+A12:2011
EN 301 489-17 V2.1.1:2010
EN 301 489-3 V1..4.1:2003
EN 301 489-1 V1.8.1:2008
EN 300 328 V1.7.1:2008
EN 50130-4:1977+A1:2000+A2:2004
EN 300 220-1 V2.1.1:2006
EN 300 220-2 V2.1.2:2008
Manufacturer/Authorised representative,
Dean Janacek
Zagreb, 30 November 2012
Tri plus grupa d.o.o.
Banjavciceva 11
10000 Zagreb
Croatia