Zipato ZIPATILE User manual

Quick-Start Guide
v.1.0
Zipatile2 / Alloy Fusion
Zipatile
af2c,zt2+,zt2.gbs.zweu.ule,zt2.hbs.zwus.ule

1.1 | PACKAGING CONTENT
• ZipaTile2
•Quick Start Guide
•Drill template
•Multifuncional power supply
•In-wall power supply adapter
•Wall mounting bracket and screws
•VESA mounting screws
• Touch sensitive 8” screen, 800 x 1280px
• 3 programmable scene buttons
• 4 dry outputs 230 VAC, 1A (60 W max)
• 1 dry input 230 VAC
• HVAC interface (support for 2-5 wire thermostat installations, HVAC version only)
• Security camera with privacy switch
• Multi-sound alarm siren, 100 dB @ 10 cm
•Stereo speakers 2 x 1W
• Microphone
• Ethernet (built-in)
• RS-485 interface
• Motion sensor
• Noise sensor
• Temperature sensor
• Humidity sensor
• Light sensor
1.0 | UNPACKING
1.2 | FE ATURES
ZipaTile2 is a multi-functional smart home controller.
It can be easily mounted in any home. Featuring a large number of built-in sensors
and hardware modules, ZipaTile2 can replace a number of home devices, like security
system, thermostat, automation controller, IP camera, alarm siren or intercom, and
brings them all together in one smart, beautiful device.
THANK YOU FOR BUYING
Zipatile2 / Alloy Fusion

Wire terminals
(see 3.0 | Wiring)
Wire release holes
Temperature and humidity sensors
Stereo speakers
Volume buttons
+
-Signal LED
Siren
VESA
mounting holes
Ethernet Power USB
Battery
Camera privacy slider
Reset
SD card SIM card
8” screen
Buttons
Light sensor
Motion sensor
Microphone
Noise sensor
Security camera

2.2 | INSTRUCTIONS
DRILL TEMPLATE
1. Choose your mounting location. Tape the Drill template, logo side up, in the location you want to
install your ZipaTile2. Make sure it is leveled.
2. Drill through the four marked screw hole locations with a 1/5” (6mm) bit suitable for your wall type.
3. Make sure you have enough room (or a hole in the wall) to route all the wires and cables on the back side
2.0 | MOUNTING ZIPATILE2 ON A WALL
2.1 | REQUIREMENT
•Screwdrivers: flathead and Philips
• Pliers
•Wire stripper / wire cutter
•Non-contact voltage detector
•Electrical tape
•Drill and drill bits appropriate for the wall type
NOTE Use safety goggles and gloves when drilling holes in the wall for screw anchors.
NOTE This product should not be plugged in sockets that can be turned off with a switch.
Risk of Electrical Shock Before performing any electrical work, turn OFF the power to the AC
wires leading into the in-wall box at the main power source. Before starting the installation, use a
non-contact voltage detector to ensure that there is no power to any wires in the wall box.
CAUTION! Installations should be performed in accordance with all national and local electrical codes. If
you are unsure or have questions about the installation, please seek the advice of a qualified electrician. Do
not apply power to the ZipaTile2 before completing the installation. Please make sure that a proper power
cut-off device is part of your power supply circuit (electrical fuse).
Wall mount with Built-in Power Supply
of the ZipaTile2. Use the area marked on the drill template (129x30mm) to check.
4. Remove the drilling template.
5. Insert the plastic inserts into holes in the wall. Push them 3 mm deeper into the wall, to make room for
bulges on the wall mounting bracket.
6. Place the ZipaTile2 wall holder over the holes and install it using the provided screws.
2.2.1 | WALL MOUNT WITH BUILT-IN POWER SUPPLY (recommended)
For compact wall mounting into an in-wall box, clip-on wire adapter onto the power supply and connect
the adapter wires to the AC wires.
2.2.2 | WALL MOUNT WITH PLUG-IN POWER SUPPLY
If there is no in-wall box at the desired mounting location, please use the wire channel at the back of the
device to place the power wires behind the ZipaTile2 and use the bundled plug-in power supply to connect
to a wall socket.
Wall mount with plug-in Power Supply

3.0 | WIRING
3.1 | POWER OPTIONS
ZipaTile2 can be powered in three different ways:
1. USB power adapter
2. PoE (Power over Ethernet)
3. HVAC installation (C wire)
Normally, use the included power supply and connect the micro-USB connector to the power port
of ZipaTile2 unit. If the ZipaTile2 is equipped with PoE module (see section 8.0 | Model numbers
nomenclature description), it can also be powered via Ethernet (when connected to PoE enabled
switch), and via 24 VAC from HVAC wiring (in this case C (common) wire needs to be connected).
3.2 | OUTPUTS/INPUTS
3.2.1 GENERAL HARDWARE VARIANT
There are two different hardware variants of ZipaTile2, differing in output configurations. Before attempting
to connect wire terminals, please check which variant you have (this info is visible on the label of the device).
For more info, refer to section 8.0 | Model numbers nomenclature description.
N
L
S1 L1 S2 L2
S4 S5 O O RS-485 A RS-485 B
N
L
N
L
N
N
Bulb 1
Bulb 2
Switch (doorbell)
RS-485 bus
Bulb 3
Bulb 4
230VAC

Press and hold (3 sec) the power button on top of the ZipaTile2. Boot process will start with the logo on the
screen and it will finish when you see the Zipato login screen.
4.0 | POWERING ON YOUR ZIPATILE2
5.1 | Wi-Fi
5.2 | ETHERNET
5.0 | CONNECTING TO THE INTERNET
ZipaTile2 has to be connected to the Internet, over the Wi-Fi or Ethernet, to configure it properly. The user
needs to open “Android Settings” to connect to the Internet. It is the standard menu where the user can
configure Network, Device, Personal and System settings related to the Android operating system.
Some wireless networks do not broadcast their names (SSID). In that case, select three dots in the
upper right corner and choose Add network from dropdown menu. To make the connection, type
the network name (SSID) and follow the above procedure from step 4. When setup completes, Wi-Fi
Connected icon appears.
If you have Wi-Fi network follow these steps:
If you have Ethernet connection follow these steps:
1. Open the Android Settings app.
2. Choose Wi-Fi.
3. Turn on Wi-Fi to view a list of available Wi-Fi networks.
4. Select one of the available Wi-Fi networks.
5. If prompted, type the network password.
6. Press the Connect button. The network is connected
immediately. If not, check your password and try again.
1. Plug ethernet cable into Zipatile2.
2. Plug ethernet cable into the ethernet port.
3. Wait until the icon appears on the status bar.
Android Settings
N
L
24VAC
Heat
System
120VAC
RS-485 bus
HVAC W HVAC RC HVAC Y HVAC RH HVAC O HVAC* HVAC C HVAC G RS-485 A RS-485 B
Cool
System
Fan
Relay
Rev.
Valve
Rev.
Valve
3.2.2 HVAC HARDWARE VARIANT
Connect only if ZipaTile2 is equipped with PoE module,
and you intend to power it from thermostat wiring.

6.0 | ZIPATO SMART-HOME APP
6.1 | LOG IN/REGISTER
Use your account’s username and password to log into Zipato app.
If you are not a registered Zipato user, you need to register your user account on Zipato server by pressing
“Register” button. You will be required to enter your name, surname, e-mail address and password, and
confirm registration by clicking the link in the e-mail that you received during this process. Now you can
log in to Zipato app.
If that doesn’t work, click “Forgot password?” and enter email addresses you used. Then, check your email
inbox – we will send password reset instructions to the account’s email address.
Login screen Register screen
6.2 | CREATING THE SYSTEM
In order to register and use your Zipatile2 with Zipato, you need to
have your own Zipato System. If you don’t have a System already,
just go to My Systems and click “+” icon to create a new one.
6.3 | REGISTERING THE ZIPATILE2
Go to your Zipato System which you want to register you Zipatile 2
to and go to Devices in the main menu. You will see Servers page
where you can register your Zipatile2 as one of the servers in your
System. Click “+” and enter a serial number of your Zipatile2 in the
dialog box.
6.4 | HELP
More info about setting up and using Zipatile2 and Zipato systems, in general, you can find in the
Knowledge base. Just go to the main menu in Zipato application and click “Knowledge base”.
NOTE For creating a System and registering Zipatile2, it is
necessary to have Zipatile2 connected to the Internet.
NOTE It is very important to upgrade applications to the latest version with App Repo application
before proceeding.

SYSTEM
Quad-Core Cortex ARM CPU
Mali400 MP2 GPU
2GB RAM
8GB FLASH
Android 8.1 Oreo
NETWORK
Ethernet (built-in)
Wi-Fi 8 02.11 b/g /n
Bluetooth 4.x
Z-Wave+ (500 series, optional)
ZigBee HA (optional)
EnOcean (optional)
433 MHz (optional)
ULE (optional)
3G/4G (cloud connection backup, optional)
DECT
SENSORS
Noise
Light
Humidity
Temperature
Motion
Shock
POWER
Power input: 5VDC
Power supply input: 100-240VAC, 50/60Hz
Power usage: <2W (Idle), 7W (Max.)
Backup battery: Li-Ion 3.7V 3500mAh
POE (Power Over Ethernet, optional)
HVAC power (using C wire, optional)
INPUT/OUTPUT
Touch sensitive 8” screen, 800x1280px
3 programmable scene buttons
4 dry outputs 230VAC, 1A (60 W max)
1 dry input 230VAC
HVAC interface (support for 2-5 wire
thermostat installations, HVAC version only)
RS-485 interface
Security camera with privacy switch
Multi-sound alarm siren, 100 dB @ 10cm
Stereo speakers 2x1W
Microphone
ACCESSORIES
Drill template
Multifuncional power supply
In-wall power supply adapter
Wall mounting bracket and screws
VESA mounting screws
PHYSICAL DIMENSION
7.9 (W) x 7.9 (H) x 0.6 (D) inches
200 (W) x 200 (H) x 15 (D) millimeters
ENVIRONMENTAL
Operating temperature: 0°C to 40°C (32°F to 104°F)
Storage temperature: -25°C to 70°C (-13°F to 158°F)
Humidity: 5% to 95% non-condensing
REGUL ATION
Safety: UL power supply
FCC
CE
RoHS
7.0 | TECHNICAL SPECIFICATION 8.0 | MODEL NUMBERS NOMENCLATURE DESCRIPTION
Model number: zt2_.ABC.D.E.F
Suffix markings from A to F, are place holders for possible variations of main board, casing and modules
types, explained below.
_ - PoE included (if yes=”+”, if no=”blank”)
A- Type of mainboard (general=”g”/HVAC=”h”)
B- housing color (black=”b”/white=”w”)
C- frame color (silver=”s”/gold=”g”)
D- Left radio module (3G/4G, 433, Zigbee=”zbee”, Z-Wave=”zw”)
E- Right radio module (ULE, Zigbee=”zbee”, Z-Wave=”zw”)
F- Socket type (A, C, G)
9.0 | DECLARATION OF CONFORMITY
We, Tri plus grupa d.o.o., Croatia, 10000 Zagreb Banjavciceva 11, declare that the product ZipaTile2 is in compliance
with all the technical regulations applicable to the product within the scope of Council Directives 2014/53/EU.
Sebastian Popovic, CEO
Manufacturer’s Name: Tri plus grupa d.o.o.
Address: Banjavciceva 11, 10000 Zagreb, Croatia
Product name: ZipaTile2
Model number: zt2
Operating temperature: 0°C to 40°C (32°F to 104°F)
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum
separation distance of 0mm must be maintained between the user’s body and the handset, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic
components. Body-worn accessories that do not meet these requirements may not comply with RF exposure
requirements and should be avoided. Use only the supplied or an approved antenna. This device in compliance
with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites
have been carried out.
1. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
2. The product shall only be connected to a USB interface of version USB 2.0
3. Adapter shall be installed near the equipment and shall be easily accessible.
4. The plug considered as disconnect device of the adapter
RF output power: This product can be used across EU member states.

DISPOSING AND RECYCLING YOUR PRODUCT
This symbol on the product or packaging means that according to local laws and regulations needs to be
disposed of separately from household waste and sent to recycling because it contains electronic components.
Once this product has reached the end of its life, please take it to a collection point (recycle facilities) designated
by your local authorities, some will accept your product for free or simply drop it off at your Zipato re-seller store. By
recycling the product and its packaging in this manner you help to conserve the environment and protect human
health. At Zipato, we understand and are committed to reducing any impact our operations and products may have
on the environment. To minimize this impact Zipato designs and builds its products to be as environmentally friendly
as possible, by using recyclable, low toxic materials in both products and packaging.
NOTICE
Although Zipato has attempted to ensure the accuracy of the content of this manual, it is possible that this document may
contain technical inaccuracies, typographical, or other errors. Zipato assumes no liability for any error in this publication,
and for damages, whether direct, indirect, incidental, and consequential or otherwise, that may result from such error,
including, but not limited to loss of data or profits. Zipato provides this publication “as is” without warranty of any kind,
either express or implied, including, but not limited to implied warranties of merchantability or fitness for a particular
purpose. The published information in the manual is subject to change without notice. Zipato reserves the right to make
changes in the product design, layout, and driver revisions without notification to its users. This version of the Installation
guide supersedes all previous versions.
TRADEMARKS
Zipato and the Zipato logo are registered Trademarks. All other product names mentioned herein may be trademarks
or registered trademarks of their respective companies.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the
receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio/
TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed
and operated at distance greater than 20 cm from your body. Use only the supplied antenna.
10.0 | ONE (1) YEAR LIMITED PRODUCT WARRANTY
Tri plus grupa d.o.o. warrants this product (the “Product”) against defects in materials and/or workmanship under
normal use for a period of ONE (1) YEAR from the date of purchase by the original purchaser (“Warranty Period”). If
a defect arises and a valid claim is received within the Warranty Period, then as your sole remedy (and Tri plus
grupa’ sole liability), Tri plus grupa will at its option either 1) repair the defect at no charge, using new or refurbished
replacementparts, or 2)replace the Product with a new product that isfunctionally equivalent tothe original, in
each case within 30 days following receipt of the returned Product. A replacement product or part assumes the
remaining warranty of the original Product. When a Product or part is exchanged, any replacement item becomes your
property and the replaced Product or part becomes Tri plus grupa’ property.
Obtaining Service: To obtain warranty service, visit https://community.zipato.com to open a service request. Please
be prepared to describe the Product that needs service and the nature of the problem. A purchase receipt is required.
The Product must be insured and shipped freight prepaid and securely packaged. You must contact support for a
Return Material Authorization Number (“RMA Number”) before shipping any Product, and include the RMA Number, a
copy of your purchase receipt and a description of the problem you are experiencing with the Product. Any claim
under this Limited Warranty must be submitted to Tri plus grupa before the end of the Warranty Period. Exclusions:
This warranty does not apply to a) damage caused by failure to follow instructions relating to the Product’s use
or the installation of components; b) damage caused by accident, abuse, misuse, transport, neglect, fire, floods,
earthquake or other external causes; c) damage caused by service performed by anyone who is not an authorized
representative of Tri plus grupa; d) accessories used in conjunction with a covered Product; e) a Product or part that
has been modified to alter functionality or capability; f) items intended to be periodically replaced by the purchaser
during the normal life of the Product, including, without limitation, batteries, bulbs or cables; g) a Product that is used
commercially or for a commercial purpose, in each case as determined by SmartThings.
EXCEPT FOR BODILY INJURY, TRI PLUS GRUPA SHALL NOT BE LIABLE FOR (I) ANY LOST PROFITS, COST OF
PROCUREMENT OF SUBSTITUTE PRODUCTS, OR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR (II) ANY
AMOUNTS IN EXCESS OF THE PURCHASE PRICE FOR THE PRODUCT, IN EACH CASE WHETHER RESULTING
FROM THE USE OF OR INABILITY TO USE THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS
WARRANTY, EVEN IF COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU. TO THE EXTENT PERMITTED BY APPLICABLE
LAW, TRI PLUS GRUPA DISCLAIMS ANY AND ALL STATUTORY OR IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION, WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND WARRANTIES
AGAINST HIDDEN OR LATENT DEFECTS. IF TRI PLUS GRUPA CANNOT LAWFULLY DISCLAIM STATUTORY
OR IMPLIED WARRANTIES, THEN TO THE EXTENT PERMITTED BY LAW, ALL SUCH WARRANTIES SHALL BE
LIMITED IN DURATION TO THE WARRANTY PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights and you may also have other rights, which vary from country to country.
To exercise your rights under this warranty, please follow the instructions above under the heading “Obtaining
Service”, or contact Zipato at Tri plus grupa d.o.o., Banjavciceva 11, 10000 Zagreb, Croatia.
Zipato is a registered trademark of Tri plus grupa d.o.o.
Manufacturer / Importer for Croatia:
Tri plus grupa d.o.o.
Banjavciceva 11, 10000 Zagreb
Croatia

FCC WARNING
This device complies with part 15 of the FCC Rules.Operation is subject to the
following two conditions:(1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation. Any changes or modifications
not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, this equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.

IC Caution:
- English: This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This
device may not cause interference, and (2) This
device must accept any interference, including
interference that may cause undesired operation of
the device.
- French: Le présentappareilestconforme aux CNR
d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitationestautorisée aux
deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareildoit accepter tout
brouillageradioélectriquesubi, mêmesi le
brouillageest susceptible d’encompromettre le
fonctionnement.

make your home smart
www.zipato.com