ZKTeco PB1000 Series User manual

PB1000 User Manual
Version: 2.0 Date: May, 2017

Parking Barrier User Manual
Contents
Chapter 1 Overview.................................................................................................................................... 1
1.1 Appearance and Dimensions........................................................................................................ 1
1.2 Components inside the cabinet .................................................................................................... 2
1.3 Working Principles ........................................................................................................................ 3
1.4 Specification Parameters of Product Series................................................................................. 3
Chapter 2 Product Installation.................................................................................................................... 4
2.1 Installation Precautions................................................................................................................. 4
2.2 Cable Embedding ......................................................................................................................... 4
2.3 Cabinet Installation ....................................................................................................................... 4
2.4 Boom Installation........................................................................................................................... 5
2.5 System Diagram............................................................................................................................ 7
2.6 Wiring Diagram of the Push Button Station.................................................................................. 8
Chapter 3 Troubleshoot.............................................................................................................................. 9
Chapter 4 Optional Functions .................................................................................................................. 10
4.1 Loop Detector.............................................................................................................................. 10
4.2 Boom Illuminator System............................................................................................................ 10
4.3 Photo Cell.....................................................................................................................................11
4.4 Cooling System........................................................................................................................... 12
4.5 Siren............................................................................................................................................ 12
Chapter 5 Device Maintenance................................................................................................................ 14
Appendix Wiring Diagram......................................................................................................................... 15

Parking Barrier User Manual
1
Chapter 1 Overview
1.1 Appearance and Dimensions
PB1000 series use the gray painted cabinet. It can be equipped with different types of straight booms.
Standard configuration of PB1030 and PB1060 include expansion boom. Length of expansion boom can
be up to 800mm. Dimensions are shown in the following figures.
Figure 1-1ADimensions of the PB1010
Figure 1-1B Dimensions of the PB1030

Parking Barrier User Manual
2
Figure 1-1C Dimensions of the PB1060
1.2 Components inside the cabinet
Figure 1-2 Components inside the Chassis
Four expansion
bolts
Position
sensor
Air switch
Motor
Gearbox
Handle

Parking Barrier User Manual
3
1.3 Working Principles
Power subsystem: Motor and gearbox provide power for the whole system.
Speed reduction subsystem: The speed reduction system control the lifting and falling speed of the
boom. It makes the boom slow down when the boom stop movement.
Spring balance subsystem: A compression spring provides balance for the weight of the boom to
keep the boom horizontal.
Electric control subsystem: The electric control subsystem consists of control board and position
sensor.
1.4 Specification Parameters of Product Series
Appearance
Model
Boom Type
Standard Boom Length
Lifting/
Falling
Speed
Fastening
Mode
Note
Gray
appearance
series
PB1010L
Straight
boom
3 m
1.8s
Cabinet on
the left
The 3M standard
configuration do
not include the
expansion boom.
The device has
220V and 110V
two different
types.
PB1010R
Straight
boom
3 m
1.8s
Cabinet on
the right
PB1030L
Straight
boom
4 m（the expansion boom
can be extended to 4.8
m）
3s
Cabinet on
the left
PB1030R
Straight
boom
4 m（the expansion boom
can be extended to 4.8
m）
3s
Cabinet on
the right
PB1060L
Straight
boom
5 m（the expansion boom
can be extended to 5.8
m）
6s
Cabinet on
the left
PB1060R
Straight
boom
5 m（the expansion boom
can be extended to 5.8
m）
6s
Cabinet on
the right

Parking Barrier User Manual
4
Chapter 2 Product Installation
2.1 Installation Precautions
1) Install the parking barrier on a level ground. If the ground is not solid and level, a cement base is
needed before installation.
2) The boom can be cut, but can’t be increased. After cutting the boom length, the spring balanceneeds
to be set again to achieve new balance. One screw on the bottom of the spring is designed for
adjusting new balance.
3) Don’t change the wire connection inside when power on.
4) The GND should be connected to the cabinet for secure protection.
2.2 Cable Embedding
1) Prepare φ25 protective sleeve and cable in advance.
2) Route cables to be connected through protective sleeves.
3) Use a tool to open a cable tray on the ground, see figure 2-2.
Figure 2-2 Cable embedding
2.3 Cabinet Installation
Installation Procedure
1) Use Bolt Holes Dimensioning to mark the installation position of the cabinet, as shown in Figure 2-3A.
2) Drive four expansion bolts into the Bolt Holes Dimensioning, as shown in Figure 2-3B.
3) Open the access door and install the parking barrier, as shown in Figure 2-3C.
The power wire is wrapped
and protected using the wire
sleeve when laid out under
the ground (the strong
current should be separated
from the weak current)
Control
room
Screw pad
Ground
Ground
Cabinet
Expansion bolt
4-M12
Base concrete
A standard power wire RVV3*1.0
A signal line RVV4*0.5

Parking Barrier User Manual
5
4) Install screw pads and use a wrench to tighten nuts, as shown in Figure 2-3D.
5) Close the access door.
Figure 2-3A Figure 2-3B
Figure 2-3C Figure 2-3D
2.4 Boom Installation
Boom Installation Procedure
1) Take out booms.
2) Add glue onto the connection part of the boom, fix the two parts together, as shown in Figure 2-4A.
3) Remove the protection cover on the connection part, as shown in Figure 2-4B.
4) Adjust the length of the expansion boom (only for 4M and 5M device), and fasten the screw, as shown
in Figure 2-4C.
5) Install decorative cap on the expansion boom, as shown in Figure 2-4D.
6) Install the anti-crash strip, as shown in Figure 2-4E.
7) Put the boom on the ground for 30 minutes, let the glue be solid, then mount it on the cabinet, as
shown in Figure 2-4F.
Screw pad
Ground Ground
Base
concrete
Chassis
Expansion bolt

Parking Barrier User Manual
6
Figure 2-4AApplying Glue Figure 2-4B Wiping Off Spilled Glue
Figure 2-4C Installing the Decorative Cap
Figure 2-4C Figure 2-4D
Figure 2-4EAppearance of the Straight Boom
Apply glue
Main boom
Main boom
调整距离
Wiping Off Spilled Glue
Adjust the distance
Fasten screws after
adjusting the expansion
boom
Decorative cap A
Decorative
cap B
Screw
Anti-crash strip
Decorative cap B
Expansion boom
Decorative cap A

Parking Barrier User Manual
7
Figure 2-4F Installing the Boom to the Chassis
2.5 System Diagram
Installation Diagram for the Parking barrier and Wall.
The distance between the chassis and the wall should be greater than or equal to 100 mm.
The distance between the boom and the wall should be greater than or equal to 100 mm.
Plastic decorative cap
Iron piece
Screw
Boom

Parking Barrier User Manual
8
System Diagram
2.6 Wiring Diagram of the Push Button Station
Push
Button
Station
A standard power wire RVV3*1.0
A signal line RVV4*0.5
Control
room