ZKTeco PB3000 Series User manual

User Manual
PB3000

PB3000 User Manual
1
Contents
Chapter 1 Overview..........................................................................................................................................................................................................................1
1.1 Appearance and Dimensions.................................................................................................................................................................................1
1.2 Components inside the cabinet...........................................................................................................................................................................2
1.3 Working Principles..........................................................................................................................................................................................................3
6M( main boom 3.2m + vice boom 3m ..................................................................................................................................................................3
Chapter 2 Product Installation...................................................................................................................................................................................................4
2.1 Installation Precautions...............................................................................................................................................................................................4
2.2 Cable Embedding ..........................................................................................................................................................................................................4
2.3 Cabinet Installation........................................................................................................................................................................................................4
2.4 Boom Installation............................................................................................................................................................................................................5
2.5 System Diagram ..............................................................................................................................................................................................................7
2.6 Wiring Diagram of the Push Button Station..................................................................................................................................................8
Chapter 3 Troubleshoot .................................................................................................................................................................................................................9
Chapter 4 Optional Functions.................................................................................................................................................................................................10
4.1 Loop Detector................................................................................................................................................................................................................10
4.2 Cooling System.............................................................................................................................................................................................................11
Chapter 5 Device Maintenance .............................................................................................................................................................................................12
Appendix Wiring Diagram.........................................................................................................................................................................................................13

PB3000 User Manual
1
Chapter 1 Overview
1.1 Appearance and Dimensions
PB3000 series are equipped with gray painted cabinets. PB3030 and PB3060 include main and vice boom,
PB3010 has one main boom. The dimensions are shown in the following figures.
Figure 1-1 the boom length of the PB3010
Figure 1-2 the boom length of the PB3030
Main boom
Vice boom: 1500mm
Main boom

PB3000 User Manual
2
Figure 1-3 the boom length of the PB3060
1.2 Components inside the cabinet
Figure 1-4 Components inside the Chassis
Four expansion bolts
Position
sensor
Air switch
Motor
Gearbox
Handle
Main boom
Vice boom: 3000mm

PB3000 User Manual
3
1.3 Working Principles
Power subsystem: The motor and gearbox provide power for the whole system.
Speed reduction subsystem: The speed reduction system controls the lifting and falling speed of the boom.
It makes the boom slow down when the boom stops movement.
Spring balance subsystem: The compression spring provides balance for the weight of the boom to keep
the boom horizontal.
Electric control subsystem: The electric control subsystem consists of a control board and a position sensor.
1.4 Specification Parameters of Product Series
Appearance Model Boom TypeStandard Boom Length
Lifting/
Falling
Speed
Fastening
Mode Note
Gray
appearance
series
PB3010L Straight boom 3.2 M 1.8s Cabinet on
the left
There are 200V
and 100V types
for the device.
PB3010R Straight boom 3.2M 1.8s Cabinet on
the right
PB3030L Straight boom 4.5M( main boom 3.2m + vice
boom 1.5m 3s Cabinet on the left
PB3030R Straight boom 4.5M( main boom 3.2m + vice
boom 1.5m 3s Cabinet on the right
PB3060L Straight boom 6M( main boom 3.2m + vice
boom 3m 6s Cabinet on the left
PB3060R Straight boom 6M( main boom 3.2m + vice
boom 3m 6s Cabinet on
the right

PB3000 User Manual
4
Chapter 2 Product Installation
2.1 Installation Precautions
1) Install the parking barrier on a level ground. If the ground is not solid and level, a cement base is needed
before installation.
2) The boom can be cut, but cannot be increased. After cutting the boom length, the spring balance needs to
be set again to achieve new balance. One screw on the bottom of the spring is designed for adjusting new
balance.
3) Do not change the wire connection inside when power on.
4) The GND should be connected to the cabinet for secure protection.
2.2 Cable Embedding
1) Prepare φ25 protective sleeve and cable in advance.
2) Route cables to be connected through protective sleeves.
3) Use a tool to open a cable tray on the ground, see figure 2-1.
Figure 2-1 Cable embedding
2.3 Cabinet Installation
Installation Procedure
1) Use Bolt Holes Dimensioning to mark the installation position of the cabinet, as shown in Figure 2-2
2) Drive four expansion bolts into the Bolt Holes Dimensioning, as shown in Figure 2-3.
3) Open the access door and install the parking barrier, as shown in Figure 2-4.
4) Install screw pads and use a wrench to tighten nuts, as shown in Figure 2-5.
The power wire is wrapped
and protected using the wire
sleeve when laid out under
the ground (the strong
current should be separated
from the weak current)
Control
room Screw pad
Ground
Ground
Cabinet
Expansion bolt
4-M12
Base concrete
A standard power wire RVV3*1.0
A signal line RVV4*0.5

PB3000 User Manual
5
5) Close the access door.
Figure 2-2 Figure 2-3
Figure 2-4 Figure 2-5
2.4 Boom Installation
Boom Installation Procedure
1) Take out booms.
2) Install the booms. (If your purchase is PB3010L/R, there will be only one boom. If your purchase is PB3030L/R or
PB 3060L/R there will be a main boom and a vice boom which need to be connected together.)
3) Putting the connection part of vice boom into the main boom, then fixed by 2 screws.
4) Installing the boom to the chassis.
Screw pad
Ground Ground
Base
concrete
Chassis
Expansion bolt

PB3000 User Manual
6
Figure 2-6 Connect the main boom with vice boom together
Figure 2-7 Installing the Boom to the Chassis
Fasten screws
Iron piece
Screw
Boom
Putting the vice boom into the main boom

PB3000 User Manual
7
2.5 System Diagram
Installation Diagram for the Parking barrier and Wall.
The distance between the chassis and the wall should be greater than or equal to 100 mm.
The distance between the boom and the wall should be greater than or equal to 100 mm.
System Diagram
A standard power wire RVV3*1.0
A signal line RVV4*0.5
Control
room

PB3000 User Manual
8
2.6 Wiring Diagram of the Push Button Station
Control board