ZKTeco SBTL5000 series User manual

Installation Guide
Swing Barrier SBTL5000 series
Applicable Model: SBTL5000/5200, 5011/5211, 5022/5222
Version: 1.0
Date: Jan, 2018

SBTL5000 series installation guide 1
1Overview
1.1 Preparation
A. Tools: measuring tape, adjustable wrench, impact drill and small screwdriver
(included in the package).
B. Material: PVC anti fire and insulation tube (diameter≥25mm), Standard three-core
power extension wire, M12 expansion screw (included).
C. Put the connection wire of devices into tube before laying them underground.
D. Power wire and signal wire should be set separately for distinguishing strong and
weak power. It is recommended that the wiring is to be done by a professional, and
the device must be connected to the ground.
SBTL5000 installation holes and cabling positions as shown in Figure 1-1:
Figure 1-1

2SBTL5000 series installation guide
2Installation
1. Drill holes based on the drawing of mount holes position, as shown in Figure 2-1.
Then set the expansion screw into holes.
Figure 2-1
2. Pre-fixed the device by these expansion screws. Then connect the wires between
master and slave devices. As shown in below:
Figure 2-2 (5-core: signal, 2-core: 24V power)
3. Test with temporary cable, ensure that ground wire of AC power was connected to
cabinet.
4. Turn on the air switch to test whether the device is working properly, wait for 10
seconds for the gate to complete self-test program. At the same time check
whether or not the indicator light working properly. If everything is normal, you

SBTL5000 series installation guide 3
can start the installation procedures. If an exception occurs, please contact your
vendor for information.
3Wiring Diagram
Check circuit according to the following wiring diagram:
Figure 3-1
4Menu Operation
4.1 Function of control board
A. After connecting to power, the LCD screen on control board will displays default
state, which is current Work Mode.
B. There are 4 buttons ‘UP, DOWN, ENT, ESC’below the LCD screen.
IR-L：IR1
IR-R：IR4
AP-L：IR2
AP-R：IR3
IR1，IR4 at the bottom
IR2，IR3 on the top
LED light
LED light

4SBTL5000 series installation guide
Figure 4-1
4.2 Button introduction
UP: to move up menu item or increase the value.
DOWN: to move down menu item or decrease the value.
ENT: to enter menu setting item or confirm the current modified value.
ESC: to return to the previous menu or to cancel the current operation.
4.3 Menu operation
Press the ENT button, enter the password input interface, the default password is: ‘UP,
UP, DOWN, DOWN, DOWN, DOWN’. If any step fails please press the ESC button to get
back. After entering the menu press UP or DOWN to choose a menu item and then
press ENT to enter the interface and adjust function or value.
Attention:The product has been inspected and debugged before sending out of
factory, in order to ensure that before normal usage, the system is safe and reliable. It is
also must to check the system again after installing in the field. All the above operation
should be operated by professional and parameters setting of the system shouldn’t be
changed without permission.

SBTL5000 series installation guide 5
5Troubleshooting
Number Failure description Analysis and solution
1
No response from direction
indicator or indication is not
correct.
Check whether the connection of
the roof lamp is correct or not.
2 After swiping the card, there is
only a swing arm action.
Check the master and slave
machine type setting and the 5-
core, 2-core connection line.
3 Barrier open after a long time
no closing.
Check whether the time of the
opening is too long or the IR sensor
is covered by others.
4
Motor doesn’t rotating or the
resistance too great or belt
loosen.
If the motor working properly, but
the rotated angle not enough,
which may caused by belt loosen. If
can’t solve it, try to increase the
value of twelfth menu.
5
When power on, the swing
arm can not turn back to the
initial position.
Ensure that no obstacle in the
passway, then restart the
equipment.