Zoeller QWIK JON ULTIMA 202 User manual

QWIK JON®ULTIMA 202 SYSTEM
INSTALLATION INSTRUCTIONS
PREINSTALLATION CHECKLIST
NOTICE TO INSTALLER: Instructions must remain with installation. SECTION: W2.50.025
FM2369_Ec
0214
Supersedes
1213
1. Inspect all materials. Occasionally, products are damaged during shipment. If the unit is damaged, contact your dealer before using. DO NOT remove the
test plugs from the pump.
 2. Carefullyreadalltheliteratureprovidedtofamiliarizeyourselfwithspecicdetailsregardinginstallationanduse.Thesematerialsshouldberetainedfor
future reference.
SEE BELOW FOR LIST OF NOTES
NOTES
REFER TO WARRANTY ON PAGE 2.
SEE BELOW FOR LIST OF WARNINGS
CAUTION
SEE BELOW FOR LIST OF CAUTIONS
Patent No. 7,203,976
Other Patents Pending
Product information presented
here reects conditions at time
of publication. Consult factory
regarding discrepancies or
inconsistencies.
MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347 USA
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961 USA
[phone] • FAX [phone]
®
Your Peace of Mind is Our Top Priority®
visit our web site:
www.zoeller.com
50/60Hz
 1. TheQwikJon® Ultimaisttedwith a specially-designed grinderpump
and is capable of pumping fecal matter, toilet paper and sanitary articles
which may be accidentally dropped into the toilet. It is not recommended
toushsuchforeignobjectsastheymightclogthesanitarysewer.
 2. Checktobesureyourpowersourceisadequatetohandletheamperage
requirementsofthemotorasindicatedonthepumporunitI.D.tag.
3. All plumbing (discharge and vent lines) must be installed to meet governing
codes. Unit must be vented. Do not use an automatic plumbing
vent device.
4. Maximum operating temperature must not exceed 54°C (130°F).
 5. Donotusecleaningproductscontainingbleachinthetoilettank,toiletor
attachedxturesastheywilldegradethepumpseals.
1. Repair and service should be performed by an Authorized Service Station
only (consult factory).
2. Recommended for installations with total dynamic head up to 6 m (20') for
60 Hz or 5 m (15') for 50 Hz. Consult factory if 50 Hz installation is above
5m(15')verticalheightinDN25(1")pipeorif60Hzinstallationisabove
4m(13')verticalheight.Mini-GrinderPumpisdesignedforuseinQwik
Jon®Ultima units only. It is not designed for use in any other application.
 3. Pumpswiththe“UL”markand/orthe“US”markaretested to ULStandard
UL778.CSACertiedpumpsarecertiedto CSA StandardC22.2No.
108.QwikJon®Ultima units only. It is not designed for use in any other
application.
 4. Model202toiletutilizes4.8or6.1liters(1.28or1.6gallons)perush.
 5. Allxturesconnectingtothesystemmustbeonthesameoorlevel.
1. Toreducetheriskofelectricalshock,aproperlygroundedreceptacleor
controlboxmustbeinstalledinaccordancewiththegoverningcodes.Never
remove ground pin from plug.
2.Makecertainthatthegroundfaultinterrupterprotectedreceptacleorcontrol
boxiswithinthereachofthepump’spowersupplycord.DONOTUSEAN
EXTENSIONCORD.Extension cordsthat aretoo longor toolightdonot
deliversufcientvoltagetothepumpmotor,andtheycouldpresentasafety
hazard if the insulation were to become damaged or the connection end were
to fall into a damp or wet area.
3.Makesurethepump'selectricalsupplycircuitisequippedwithfusesorcircuit
breakersofpropercapacity.Aseparatebranchcircuitisrecommended,sized
according to the governing electrical codes for the current shown on the pump
name plate.
4. Testing for ground. As a safety measure, each electrical outlet should be
checkedforgroundusinganUnderwritersLaboratoryListedcircuitanalyzer
whichwillindicateifthepower, neutral and ground wires arecorrectly connected
toyouroutlet.Iftheyarenot,callaqualiedlicensedelectrician.
5. FOR YOUR PROTECTION,ALWAYS DISCONNECT PUMPFROM ITS
POWERSOURCEBEFOREHANDLING.Ifpumpiswireddirect,de-energize
thecircuitatthecontrolbox.DONOT,UNDERANYCIRCUMSTANCES,
REMOVETHEGROUNDPIN.Wearinsulatedprotectiveshoesanddonot
standinwater.Certainplugtypesmayincludea3-pronggroundplugtohelp
protectagainstelectricalshock.Aproperlygrounded3-prongreceptacleor
control box must be installed in accordance with governing codes.
6. Installation and servicing of the pump's electrical circuits and hardware should
onlybeperformedbyaqualiedlicensedelectrician.
7. Installationandmaintenance of thisapplianceisnot intended forpersons
(including children) with reduced physical, sensory or mental capabilities, or
lackofexperienceorknowledge,unlesstheyhavebeengivensupervisionor
instruction concerning use of the appliance by a person responsible for their
safety.
8. Risk of electrical shock.Donotremovepowersupplycordandstrainrelief
or connect conduit directly to the pump. If the supply cable is damaged, it
must be replaced by an authorized Zoeller Representative.
9. Pumpcontainsoilwhichbecomespressurizedandhotwhenoperating.Allow
2½ hours after disconnecting before attempting service.
10. Pumpisnotintendedforpotablewaterduetopossiblecontaminationbyoil
contained in the pump.
11. Risk of electric shock.Thesepumpshavenotbeeninvestigatedforusein
swimming pools and marine areas.
DATE INSTALLED:
MODEL NUMBER:
© Copyright 2014 Zoeller Co. All rights reserved.

2
© Copyright 2014 Zoeller Co. All rights reserved.
Manufacturer warrants, to the purchaser and subsequent owner during
the warranty period, every new product to be free from defects in material
andworkmanshipundernormaluseandservice,whenproperlyusedand
maintained, for a period of one year from date of purchase by the end user, or
18monthsfromdateoforiginalmanufactureoftheproduct,whichevercomes
rst.Partsthatfailwithinthewarrantyperiod,oneyearfromdateofpurchase
bytheenduser,or18monthsfromthedateoforiginalmanufactureofthe
product,whichevercomesrst,thatinspectionsdeterminetobedefective
inmaterialorworkmanship,willberepaired,replacedorremanufactured
at Manufacturer's option, provided however, that by so doing we will not be
obligated to replace an entire assembly, the entire mechanism or the complete
unit.Noallowancewillbemadeforshippingcharges,damages,laboror
other charges that may occur due to product failure, repair or replacement.
Thiswarranty doesnotapplyto and thereshallbeno warrantyforany
material or product that has been disassembled without prior approval
ofManufacturer,subjectedtomisuse,misapplication,neglect,alteration,
accident or uncontrolled act of nature; that has not been installed, operated
or maintained in accordance with Manufacturer's installation instructions;
that has been exposed to outside substances including but not limited to
the following: sand, gravel, cement, mud, tar, hydrocarbons, hydrocarbon
derivatives (oil, gasoline, solvents, etc.), or other abrasive or corrosive
substances, wash towels or any other abusive entity, etc. in all pumping
applications.The warranty set outin the paragraphabove is inlieu of
all other warranties expressed or implied; and we do not authorize any
representative or other person to assume for us any other liability in
connection with our products.
ContactManufacturerat,3649CaneRunRoad,Louisville,Kentucky40211
USA,Attention:CustomerSupportDepartmenttoobtainanyneededrepair
or replacement of part(s) or additional information pertaining to our warranty.
MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL,
CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF
EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY
OFFITNESSFORAPARTICULAR PURPOSEAND OF MERCHANTABILITY
SHALLBE LIMITEDTOTHE DURATION OF THEEXPRESSEDWARRANTY.
Somejurisdictionsdonotallowlimitationsonthedurationofanimplied
warranty,sotheabovelimitationmaynotapplytoyou.Somejurisdictionsdo
notallowtheexclusionorlimitationofincidentalorconsequentialdamages,
so the above limitation or exclusion may not apply to you.
Thiswarrantygivesyouspeciclegalrightsandyoumayalsohaveother
rightswhichvaryfromjurisdictiontojurisdiction.
LIMITED WARRANTY
HELPFUL HINTS FOR EASY INSTALLATION
1. Read all instructions before beginning installation.
2. Besuretheoorislevelwithin3mm(1/8").
 3.Installventpipesealwithangesideofsealonoutsideoflid.
4. Use soapy water to lubricate all seals to aid installation.
 5. Installrubbercoupling/unioninventlinetoaiddisassembly.
 6. Donotovertorquetoiletmountingscrews.
 7. Donotuseanautomaticplumbingventdevice.
 8. Obtainmodelnumberanddatecode,andrecordinformationinthe
space provided on the front of this manual. Refer to this information
when calling the factory.
DO’S AND DON'T’S FOR INSTALLING A UNIT
1.DOreadallinstallationmaterialwiththeunit.
 2.DOinspectunitforanyvisibledamagecausedbyshipping.Contact
dealer if unit appears to be damaged.
DO’S AND DON'T’S, continued
 3.DOcleanallvisibledebrisfromtheunit.
 4.DOalwaysdisconnectpumpfrompowersourcebeforehandling.
DOalwaysconnecttoaseparatelyprotectedandproperlygrounded
groundfaultprotectedcircuit.DONOTevercut,spliceordamage
powercord.DONOTcarryorliftpumpbyitspowercord.DONOT
use an extension cord.
 5.DO install a ball or gate valve and a union in the discharge line
downstreamofthecheckvalve.
 6.DOtestpumpimmediatelyafterinstallationtobesurethatthesystem
isworkingproperly.
 7.DOreviewallapplicablelocalandnationalcodesandverifythatthe
installation conforms to each of them.
 8. WeDONOTrecommendthisproductbeconnectedtoutilitiesotherthan
thosefoundinanormalbathroomapplication.Washingmachinesand
dishwashersareexamplesofequipmentthatweDONOTrecommend.
 9. DOinspectandtestsystemforproperoperationsatleastevery3months.
TYPICAL PIPING CONFIGURATIONS
SK2587
Installation may not be
exactly as shown. Refer
to step 1 on page 5 for
piping details.
2.4m(8')
CEILING*
2.1m(7')
CEILING*
20.32 cm (8")min.
CHECKVALVE
P/N30-0181
*Ceilingheightsshownforreferenceonly.
NOTE: All installations must
comply with all applicable
governing codes.

3
© Copyright 2014 Zoeller Co. All rights reserved.
SERVICE PARTS
QWIK JON®ULTIMA 202
202-A
No Plug
STANDARD
202-A
G-Plug
STANDARD
202-A
G-Plug (white)
STANDARD
202-A
E/F Plug
STANDARD
202-A
E/F Plug
PREMIUM
202-A
E/F Plug
STANDARD
202-A
G-Plug
STANDARD
12 /10
to
Current
3/12
to
Current
1 / 11
to
Current
9 / 11
to
Current
3/12
to
Current
3/12
to
Current
7/12
to
Current
Item Description Part No.
1 Qwik Jon®Ultima Sewage Removal System 202-1001 202-1005 202-1002 202-1003 202-1010 202-1006 202-1012
2 Replacement pump with discharge pipe 150872 151965 151965 151895 152167 151966 152296
3Tank cover with discharge ttings 017373 017373 017373 017373 017373 017373 017373
4 Tank 018500 018500 018500 018500 018500 018500 018500
5 Seal 017350 017350 017350 017350 017350 017350 017350
6 Rubber coupling with hose clamps 151563 151563 151563 151563 151563 151563 151563
7 Extension kit for behind the wall install. (optional) 10-3050 10-3050 10-3050 10-3050 10-3050 10-3050 10-3050
3
1
2
4
6
5
7
SK2838

4
© Copyright 2014 Zoeller Co. All rights reserved.
CONDITION POSSIBLE CAUSE REMEDY
A. PUMP WILL NOT START OR RUN
Lowvoltage,blownfuse,opencircuit Haveaqualiedelectriciancheckfuseandcircuit.
Impeller bound Contact a Zoeller Service Station.
Motor or wiring shorted
Debrisonoatswitch Remove debris.
B. PUMP STARTS TOO SOON Float“ON”pointisadjustedtoolow Raisetheoatstops,makesuretheoatisbetweenthetwostops.
C. WATER LEVEL EXCESSIVE BEFORE PUMP TURNS ON Float“ON”pointadjustedtohigh Lowertheupperoatstop.
D. PUMPWILLNOTSHUTOFFORRUNSTOOLONG BEFORE
WATER IS PUMPED
Debrisunderoat Removedebrisfromaroundoat.
Faultyoatswitch Contact a Zoeller Service Station.
Float“Off”pointadjustedtoolow Raisetheloweroatstop.
Pumpisairlocked Makesureventholeindischargepipeisclear.
Waterleveltoolow Raisetheloweroatstop.
Wastematerialhasaccumulatedblockingowofmaterial
topumpintake.
Holdushhandledownontoiletfor15seconds.Ifunitwillnot
clear,unplugandwait30minutes.Plugunitbackinandrepeat.
If unit still will not turn off, it will need to be opened and the
debris relocated.
E. PUMP OPERATES BUT
DELIVERS LITTLE OR NO WATER
Debrisaroundintake Cleanareaaroundintake.
Blockageindischargepipe Removepipeandushoutdebris.
Loworincorrectvoltage Haveaqualiedelectriciancheckhousewiring.
DamagedImpeller Contact a Zoeller Service Station.
Incorrectoatadjustment ContactProductSupportDepartment.
Pumpisairlocked Makesureventholeindischargepipeisclear.
Vertical lift too high ChangedischargepipingorcontactProductSupportDepartment.
SK2844
DIMENSIONS
TROUBLE SHOOTING
Iftheabovechecklistdoesnotsolvetheproblem,consulttheZoellerProductSupportDepartmentat+1(502)778-2731.Do not attempt to service or otherwise disassemble pump.
Before servicing a pump, always shut off the main
power breaker and then unplug the pump - making sure you
are not standing in water and are wearing insulated protective
sole shoes. Under ooded conditions, contact your local electric
company or a qualied, licensed electrician for disconnecting electrical
service prior to pump removal.
Submersible pumps contain oil which become pressured
and hot under operating conditions. Allow 2½ hours after disconnecting
before attempting service.
CAUTION
Do not dispose of feminine sanitary products, disposable
diapers, dish rags, etc. in the QWIK JON®ULTIMA . They may jam the
pump or other plumbing lines and cause malfunction.
CARE OF FINISH: Soap and water is all that is recommended for cleaning
the outside of the tank. Other cleaning products may cause discoloration
and scratching.
[18 5/8”]
[20 1/8”]
[1 3/4”]
[14 1/2”]
[7”]
[12 3/4”]
[15 1/2”]
[9”]
[9 3/16”]
[2 7/8”]
[3 1/2”]
47.3cm
22.9cm
23.3cm
36.8cm
4.4cm
51.1cm
7.3cm
17.8cm
39.4cm
32.4cm
8.9cm

5
© Copyright 2014 Zoeller Co. All rights reserved.
QWIK JON
®
ULTIMA QWIK REFERENCE GUIDE
STEP 1 LOCATION SELECTION
Plan your new installation carefully.
Floor:Theoorshouldbestructurallysoundandlevelwithin3mm(1/8").Ifthe
oorisnotlevel,usehydrauliccementorsimilarmaterialtoleveltheoor.
Water:Awatersupplywillbeneededtooperatethetoilet.UsuallyaDN15(1/2")
linewithashut-offvalveissufcient.
Electrical:Areceptacle of the appropriate voltage will be needed to supply electrical
power to the pump.
Sewage:Accesstoasewagelineisrequired.TheQwikJon®UltimarequiresaDN25
(1")(orDN20[3/4"]ifyourcodespermit)sewagedischargelinetoconnecttoan
existing sewage line. A ball or gate valve should be installed in the discharge line.
Vent:Accesstoaventpipeisrequired.Theuseofamechanicalventsystemis
NOTrecommendedasthetoiletwillnotush.
NOTE:Ifabuilt-ininstallationistobeused,locatethepumpunitinanareathat
will allow access to the pump and switch.
OUTLET
WATER
SUPPLY
DISCHARGE
PIPE
VENT
PIPE
LEVEL FLOOR
BALL OR GATE VALVE
SOLD SEPARATELY.
SK2588
STEP 2 LEVELING OF PUMP UNIT
CAUTION
Donotusewoodenshimstolevelthepumpunit!
CAUTION
Ensurethatnails,screwsorothersharpobjectsdonotpuncturethepumpunit!
Levelthepumpunittowithin3mm(1/8")usinghydrauliccementorsimilarmaterial.
SK2589
STEP 3 ROUGH-IN
1) Positionthepumpunitaminimumof3mm(1/8")fromthewall
with the inlet facing forward. Attach the bellows to the inlet using
the worm drive clamp provided.
 2) Placethetoiletinfrontofpumpunitaligningthedischargeofthe
toiletwiththeinletofthepumpunit.Makesurethatthebellows
willbridgethegap adequatelyfornalinstallation.Thetoilet
tankshouldbeaminimumof13mm(1/2")fromthewall.
 3) Lightlymarkthelocationsofthepumpunit,toiletandcloset
boltlocationsontheoor.Lightlymarkthewallwiththeheight
ofthepumpunitandthebottomandsidesofthetoilettankto
ensure against interference from pipe runs later.
4) Remove the toilet from the pump unit and set it aside.
SK2590
(STAND-ALONE INSTALLATION) (BEHIND-THE-WALL INSTALLATION)
1) Installing the grinder unit behind a wall will require an
extensionkit(P/N10-3050)soldseparately.
 2) Placethetoiletassemblyaminimumof13 mm (1/2") from
thewallandmarktheclosetboltlocationsontheoor.
 3) MeasuretheappropriatelengthofDN90(3½")Schedule
40PVCpipeprovidedwiththeextensionkitandcutitto
length.Seesketchbelow.
4) Set toilet aside.
CAUTION
 Toilet assembly is top heavy. Take special
precautionstoensurethattoiletdoesnottipoverandbreak.
SK2634

6
© Copyright 2014 Zoeller Co. All rights reserved.
STEP 4 PIPING
1) Cutanddry-tthepipeandttingsasrequiredforDN25(1")diameter
dischargepipe(maybereducedtoDN20[¾"]diameter if codes permit).
 2) Whiledry-ttingthedischargepipe,positionandmarkthelocationof
thepumpunitdischargetting.
3) Cutanddry-tDN40(1½")ventpipeasrequiredtoensurethatthe vent
pipedoesnotinterferewithothercomponents.Maketheconnectionto
thepumpunitwiththeprovidedstreetelbow.A2"x1"90°discharge
ttinghasbeenprovided.However,itmaybeeasiertopipestraight
up depending on the installation.
CAUTION
Properventingisrequired.Donotuseamechanical
type vent.
 4) Temporarily set the toilet in place to check that there is no piping
interference. Remove the toilet and set it aside.
5) Clean, prime and solvent weld the discharge piping and pump unit
dischargetting.
CAUTION
Whenapplyingsolventweldtodischargetting,ensurethat
nonegetsintothecheckvalveassembly.Paycloseattentiontotheproper
alignmentofthedischargettingpreviouslymarked.
 6) Cleanandsolventweldventpipingasrequiredforproperventing.
Note: Addingotherbathroomxtures-TheQwikJon®Ultima is designed to
acceptadditionalbathroomxturesutilizingthetwosideinlets.Theseinlets
can be attached via the 2" MPT (outside diameter) or the 1½" slip (inside
diameter).Theseinletsmusthavetheinnerportiondrilledoutusinga44mm
(1¾")holesaw.Thisistoensurethereisnoleakageproblemsfrominletsnot
inuse.Whenutilizingsideinlets,installacheckvalveontheincomingline.
SK2591
DRILL POINT
1-1/2" SLIP INSIDE
2" MPT OUTSIDE
SK2586
SK2589
 1) Installtheclosetboltsatthepointsmarkedearlier.
 2) Placethetoiletassemblyovertheclosetbolts.Installtheanchoring
hardwareandtighteninanalternatingpattern.Checkforlevelandshim
asrequired.Becarefulwhentighteningboltsornutsagainstchinato
avoidcrackingthechina.
 3) Installrubberbellowsontothetoiletdischargeandgrindertankhub
andsecurewiththewormclampsprovidedforinstallation.Seesketch
inStep3.Forbuilt-ininstallation,installtherubbercouplingstoboth
thegrindertankandthetoiletdischargeandsecuretoextensionpipe
withwormclampsprovided.SeesketchinStep3.
 4) Installthewatersupplylinefromtheexistingwatershut-offvalvetothe
toilet water supply connection.
 5) Openthewatersupplyvalveandcheckforleaks.Thetoilettankshould
lltotheproperlevel.Adjustifrequired.
 6) Plugthepump'spowercordintotheoutlet.
 7) Flushthetoiletandwatchforproperoperation.Listenforthepumpto
start.Thepumpunitrequiresproperventinginorderfortoilettoush.
Checkforleaks.
 8) Repeatushcyclestoassureproperoperation.
FLOOR LEVEL TO WITHIN 3 mm (1/8")
PUMP UNIT
AUX. INLET
WATER
SUPPLY
OUTLET
DISCHARGE
PIPE VENT PIPE
(PER ALL CODES.
DO NOT USE
MECHANICAL VENT.)
SK2595
STEP 5 TOILET INSTALLATION (TOILET SUPPLIED BY OTHERS)
DONOTPUTGLUE
INTHISAREA
NOTE: May not be pictured exactly as shown.

7
© Copyright 2014 Zoeller Co. All rights reserved.
SK2845
SK2909
1%
6 m (20’)
8 m (25’) DN25 (1”) pipe max. 17 m (56’)
DN20 (¾”) pipe max. 17 m (56’)
DN25 (1”) pipe max. 81 m (266’)
DN20 (¾”) pipe max. 67 m (220’)
DN25 (1”) pipe max. 149 m (489’)
DN20 (¾”) pipe max. 119 m (390’)
DN25 (1”) pipe max. 218 m (715’)
DN20 (¾”) pipe max. 171 m (561’)
2 m (6.5’)
4 m (13’)
50 Hz
60 Hz
1.5 m (5')
3 m (10')
4 m (13')
5 m (15')
1%
DN25 (1") PIPE MAX. 146m (479')
DN20 (3/4") PIPE MAX. 116m (381')
DN25 (1") PIPE MAX. 96m (315')
DN20 (3/4") PIPE MAX. 78m (256')
DN25 (1") PIPE MAX. 62m (203')
DN20 (3/4") PIPE MAX. 53m (174')
DN25 (1") PIPE MAX. 28m (92')
DN20 (3/4") PIPE MAX. 27m (89')

8
© Copyright 2014 Zoeller Co. All rights reserved.
STEP 7 PUMP PERFORMANCE
TOTAL DYNAMIC HEAD
FLOW RATE
0
METERS
TOTAL DYNAMIC HEAD/FLOW
SEWAGE
m /hr
3
2
1
7 m (23’)
2.52.0 6.6
3.0
Shut-off Head:
9.8 2.2
MODEL
Meters
1.5 5.0
Feet L/sec
2.7
9.0
8.0
9.6
13.14.0 1.96.7
FEET
L/sec
m /hr
3
202
0
46810 12
1 2 3
PUMP PERFORMANCE CURVE
MODEL 202 50 Hz
2
3
4
8
5
10
15
5.0
6.0
16.4
19.7
5.1
3.4
1.4
0.9
6
5
20
7
25
150869
DECLARATION OF CONFORMITY
WeZoellerdeclareunderoursoleresponsibilitythatthemodel202towhichthisdeclarationrelates,isinconformitywiththeCouncilDirectives
on the approximation of the laws of the EC Member States relating to:
PumpConformsto:
--MachineryDirective(2006/42/EC)
 Standardsused:EN809:1998
--ElectromagneticCompatibility(2004/108/EC)
 Standardsused:EN61000-3-2,EN61000-3-3andEN55014-1
--Electricalequipmentdesignedforusewithincertainvoltagelimits
 (2006/95/EC)
 Standardsused:EN60335-1:2002andEN60335-2-41:2003
System Conforms to:
--ConstructionProductsDirective(89/106/EEC)
 Standardsused:EN12050-3:2001
018512
METERS FEET
L/sec
m /hr
3
1
PUMP PERFORMANCE CURVE
MODEL 202/203/204 60Hz
2
3
4
5
6
10
62 4 108 12
8
7
9
TOTAL DYNAMIC HEAD
FLOW PER MINUTE
Shut-off Head:
9.83.0
FeetMeters
5.0
6.6
1.5
2.0
MODEL
9.1 m (30’)
9.1 2.5
10.2
9.8
2.8
2.7
202/203/204
13.14.0 8.4 2.3
16.45.0 7.4 2.1
19.76.0 6.2 1.7
23.07.0 4.6 1.3
26.28.0 2.6 0.7
m /hr
3
L/sec
0
0
FLOW RATE
1 2 3
TOTAL DYNAMIC HEAD
5
10
15
20
25
30