Zoom 4506 User manual

Travel Router with Wireless-N
USER MANUAL

NOTICE
This document contains proprietary information protected by copyright, and this Manual and
all the accompanying hardware, software, and documentation are copyrighted. No part of this
document may be photocopied or reproduced by mechanical, electronic, or other means in
any form.
The manufacturer does not warrant that the hardware will work properly in all environments
and applications, and makes no warranty or representation, either expressed or implied, with
respect to the quality, performance, merchantability, or fitness for a particular purpose of the
software or documentation. The manufacturer reserves the right to make changes to the
hardware, software, and documentation without obligation to notify any person or
organization of the revision or change.
All brand and product names are the trademarks of their respective owners.
© Copyright 2011
All rights reserved.

MENT
Contents
Contents........................................................................................................................3
Chapter 1: Installing the Travel Router with Wireless-N ........................................5
Package Contents.................................................................................................. 5
System Requirements............................................................................................ 5
Installing the Battery............................................................................................. 6
Powering Your Router........................................................................................... 6
Using AC Power ........................................................................................... 6
Reading the Power Indicator (LED)............................................................. 6
Connecting a Modem or Smartphone to Your Router........................................... 7
Connecting a Mobile Broadband Modem or Tethered Phone............................... 7
Resetting the Router to the Factory Configuration............................................. 10
Chapter 2: Using the Configuration Manager........................................................11
Launching the Router's Configuration Manager................................................. 11
Launching the Configuration Manager's Setup Wizard...................................... 12
Step 1. Setup Login..................................................................................... 13
Step 2. Setup Time Zone............................................................................. 14
Step 3. WAN Type Setup ............................................................................ 14
Configuring the WAN Type........................................................................ 15
Step 4. Wireless Settings............................................................................. 21
Step 5. Summary......................................................................................... 25
Step 6. Finish .............................................................................................. 26
Chapter 3: Wireless and Wireless Security Setup...................................................27
WPS Configuration............................................................................................. 27
Configuration Methods............................................................................... 27
Method One ................................................................................................ 27
Method Two................................................................................................ 28
Method Three.............................................................................................. 28
Configuring Wireless Security Manually............................................................ 29
WPA2/WPA Configuration......................................................................... 29
WEP Configuration..................................................................................... 30
Chapter 4: Using the Configuration Manager's Advanced Program...................33
Changing Default Settings.................................................................................. 33
Online Help......................................................................................................... 34
Launching the Configuration Manager's Advanced Program............................. 34
Configuring Basic Settings......................................................................... 35
The Basic Setup Page.................................................................................. 35
The DHCP Server Page............................................................................... 38
The Wireless Setting Page .......................................................................... 38
The Change Password Page........................................................................ 41
Configuring Forwarding Rules................................................................... 41
The Virtual Server Page.............................................................................. 42
The Port Triggering Page............................................................................ 43
The Miscellaneous Page ............................................................................. 44
Contents 3

Configuring Security Settings..................................................................... 45
The Status and Packet Filters Pages............................................................ 45
The Domain Filters Page ............................................................................ 46
The URL Blocking Page............................................................................. 47
The MAC Address Control Page................................................................ 48
The Miscellaneous Page ............................................................................. 49
Configuring Advanced Settings.................................................................. 49
The System Log Page ................................................................................. 50
The Dynamic DNS Page............................................................................. 51
The QoS Page ............................................................................................. 51
The SNMP Page.......................................................................................... 53
The Routing Table Page.............................................................................. 54
The System Time Page................................................................................ 54
The Schedule Rule and Schedule Rule Setting Pages ................................ 55
Configuring Toolbox Settings..................................................................... 57
The System Information Page..................................................................... 58
The Firmware Upgrade Page...................................................................... 58
The Backup Setting Dialog......................................................................... 58
The Reset to Default Dialog ....................................................................... 58
The Reboot Dialog...................................................................................... 59
The Miscellaneous Page ............................................................................. 59
Appendix A: Mobile Broadband Settings................................................................60
Appendix B: How to Set Up Tethering on the iPhone®..........................................63
Appendix C: Registering Your Product and Getting Help.....................................65
Limited Warranty................................................................................................ 66
FCC Interference Statement................................................................................ 66
CE Declaration of Conformity............................................................................ 66
Declaration of Conformity........................................................................................67
4 TravelRouterwithWireless-NUserManual

1
Installing the Travel Router with
Wireless-N
Package Contents
The package contains the Zoom Travel Router with Wireless-N, a Li-ion battery, an
RJ-45 Ethernet cable, a 5V 2.0A Power adapter, a Quick Start installation manual,
and a CD that contains additional documentation and warranty information.
If anything is missing or damaged, please contact Zoom Customer Support or
whoever provided the Travel Router.
System Requirements
Any DSL or cable modem or modem/router that has an Ethernet port should work with
the Travel Router. The Travel Router also works with many but not all mobile
broadband USB modems and tethering-enabled smartphones. For an up-to-date list
of modems and smartphones known to be compatible with the router, please go to
www.zoomtel.com/travelrouter/comp. We attempt to support all popular mobile
broadband (such as 3G, 4G, LTE) USB modems and tethering-enabled smartphones,
but this is challenging because new ones are introduced almost every day. If you’d
like to let us know about a mobile broadband modem or smartphone that is
incompatible with the router, please send an email to [email protected]
You can even use your mobile broadband modem as a backup to your DSL or cable
modem. If the DSL or cable Internet connection fails, the Travel Router can be set up
to automatically switch over to mobile broadband for Internet access.
The Travel Router’s WiFi®-compatible wireless capability works with WiFi®-compatible
devices including wireless n, g, and b devices.
Chapter1.InstallingtheTravelRouterwithWireless-N 5

Installing the Battery
You need to install the battery one time before you use your router. To install the
battery, please follow these steps:
1Remove the battery cover on the bottom of the router and slide the Li-ion battery
into the router's battery holder.
2Replace the battery cover.
Powering Your Router
If the Zoom Travel Router’s battery is charged, you can use the router without
plugging it into AC power.After it’s fully charged, the battery will typically power the
router for 3 hours or more, depending on how actively you’re using mobile broadband
and wireless n/g/b. When you’re not using the router, you should switch it OFF.
Using AC Power
To use AC power, plug the router’s power cube into an AC outlet and into the POWER
jack on the back of the router.
POWER jack
Then you can use the router AND charge the battery at the same time automatically,
or you can only charge the battery. If you’re only charging the battery, it’s best to have
the router switched OFF. Charging typically takes about 2 ½ hours when the router is
switched OFF.
Reading the Power Indicator (LED)
The Power indicator (LED) tells you the following when the router’s power switch is
ON:
•
•
•
•
Solid Green: The power cube is plugged in and the battery is fully charged.
Flashing Green: Power is being provided by the battery, not the power cube.
Amber: The power cube is charging the battery.
Red: The battery is low and the power cube is not plugged in.
6 TravelRouterwithWireless-NUserManual

Power LED
Connecting a Modem or Smartphone to Your Router
If you wish to use the router with a DSL or Cable connection, please go to Chapter 2:
Using the Configuration Manager. If you wish to use the router with a mobile
broadband modem or tethered phone, please continue below.
Connecting a Mobile Broadband Modem or Tethered Phone
If you are considering using the router with a tethered phone,
please consider the following:
¾Many service providers do not allow you to connect your mobile
phone to a computer or router unless you have signed up for a data
plan that allows data tethering. These plans are commonly called
Data Tethering, Mobile Broadband Connect, 3G Mobile Hotspot,
Phone as a Modem, or Laptop Connect.
¾Your router only supports tethering with the USB cable. It does not
support tethering over WiFi®or Bluetooth®.
¾When using your Phone as a modem you should turn off WiFi®and
Bluetooth®to conserve the phone’s battery.
¾You may need to change the settings of the USB port on your phone
that’s being used with tethering. Refer to your phone’s
documentation on how to do this or go to
www.zoomtel.com/tethering for some information for common
phones or see Appendix B for instructions on Tethering on the
iPhone®.
¾If you have difficulty connecting to the Internet through your phone,
verify that you can browse the internet with your phone directly
connected to a PC. If you can’t browse with the phone connected
directly to a PC, contact your wireless service provider for help. If
you can connect through your PC but not when attached to the
Travel Router, please contact Zoom Support. See Registering your
Product and Getting Help at the end of this Quick Start.
Chapter1.InstallingtheTravelRouterwithWireless-N 7

1If you are using a mobile broadband USB modem to connect to the Internet, plug the
USB modem into the router’s USB port (see 1.1). If you are using a Phone to connect to
the Internet plug one end of the USB cable that came with your phone into the router and
the other end into your phone (see 1.2).
1.1 1.2
2If you don’t want to power the router with its rechargeable battery, connect the power
adapter to the receptor on the back panel of your router and plug the other end of the
power adapter into a wall outlet or power strip.
3Turn on the router's POWER switch, located on the rear panel.
ON/OFF switch
POWER jack
4The Power indicator on the router's top panel turns on, then the WiFi®and USB LEDs
blink green. The WiFi®LED continues to blink to signify activity.
5After the router is powered up, the router’s USB LED should turn solid green within 2
minutes indicating that a mobile broadband connection has been made and that the
router has gotten an IP address. If the USB LED does not turn solid green, unplug the
modem or phone, plug it in again, and wait to see whether the USB LED turns solid green
within 2 minutes. If the USB LED still does not turn and remain solid green, see
Troubleshooting Your Internet Connection below.
WiFi
®
LED
Ethernet LED USB LED
8 TravelRouterwithWireless-NUserManual

6A computer, mobile phone, game station, or other device with wireless 802.11n, g, or b
capability can access the Internet wirelessly through the mobile broadband router. To
make the wireless connection, you must first locate the wireless network connection
setup on your device, and then select the Zoom network. For example, on Windows
computers, click the wireless connection icon on the Task Bar, click Available Wireless
Networks, select Zoom from the list of available wireless networks, and then make the
connection.
7The router comes set up for wireless with no security. If you want wireless security, you
need to set up the router and each device for the security that you want.
•If all of the devices on your network support WiFi Protected Setup (WPS), please
refer to WPS Configuration on page 27 for detailed information and instructions.
•Alternately, you can use the Configuration Manager's Setup Wizard, which
includes wireless setup. For more information and instructions, please refer to
Chapter 2: Using the Configuration Manager, starting on page 12.
8You may want to plug a computer or other device into the router’s Ethernet port. This is
recommended if you’re changing the router’s default values, and sometimes an Ethernet
connection is more convenient or secure than connecting to the router wirelessly. To
connect via Ethernet, simply plug the router’s Ethernet cable between the router’s
Ethernet port and your computer or other device’s Ethernet port.
9Open your browser on your computer or other device and verify that your are able to
connect to the Internet. If you are unable to connect, refer to Troubleshooting section
below.
If you are able to connect to the Internet and you have already set up wireless security (or are
choosing not to), your setup is complete. Congratulations!
Troubleshooting Your Internet Connection
If you are unable to connect to the Internet through your router, please check the
following:
1Verify that you are in a mobile broadband coverage area and that your phone or
modem can receive a signal at your location. You may want to try changing the
location of your router, for example, by moving the router closer to a window.
2If you are using a tethered mobile phone, go over the points in the If you are
considering using the router with a tethered phone, please consider the
following box.
3Verify that your phone or modem is recognized by your router. To do this:
a. Login to the router as described in steps 1-3 of Launching the Router’s
Configuration Manager in Chapter 2: Using the Configuration
Manager.
b. Click on Status.
c. Locate the Card Info field on the Status page to see if your card is
recognized. If your card is not seen under Status, verify that your modem
or phone is compatible with your router. See
www.zoomtel.com/travelrouter/comp for a list of compatible modems
and phones. If your device is listed and you are still having trouble, please
Chapter1.InstallingtheTravelRouterwithWireless-N 9

contact Zoom support as described in the section Registering Your
Product and Getting Help.
4You may need to manually configure the router to recognize your phone or
modem. Please see Chapter 2: Using the Configuration Manager.
Resetting the Router to the Factory Configuration
In the unlikely event that you need to reset the router to the factory default
configuration, insert the blunt end of a paper clip into the RESET hole on the side
panel of the router. Hold the clip in place for seven (7) seconds.
Please continue to Chapter 2.
10 TravelRouterwithWireless-NUserManual

2
Using the Configuration Manager
Your Travel Router with Wireless-N is preset with default values that meet the needs
of most users. However, you can change these settings using the router's built-in
Configuration Manager.
Here are some reasons why you might want to use the Configuration Manager:
•You have a DSL or cable modem.
•You want to set or change some settings of your Travel Router. For instance,
you may want to change the login password or time zone or change wireless
settings to, for instance, turn on WiFi®-compatible security.
•You want to use WPS to set up your WiFi®-compatible connection. WPS
simplifies wireless setup, but all your WiFi®-compatible devices need to
support WPS.
•You want to set up some advanced features of the Travel Router such as a
virtual server or DMZ for use with online gaming. You can find a summary of
those features in the Changing Default Settings section near the start of
Chapter 4, on page 33.
Launching the Router's Configuration Manager
To launch the Configuration Manager, please follow these steps:
1If you haven't already done so, plug the supplied Ethernet cable into the
Ethernet port on the router’s back panel and into your computer’s Ethernet
port.
2Turn on your computer and router, then launch the computer’s Web browser.
3In the Web browser address bar, type the router's default IP address,
http://192.168.1.1 and then click Enter.
When the MAIN MENU opens for the first time, it displays a System Status page
that summarizes the current settings and values for your system.
Chapter2:UsingtheConfigurationManager 11

4On the Toolbar, type admin (the default password) in the System Password field,
then click Login.
Note: Later, if you change the System Password, you will use the new password to
log in.
When you log in, the Configuration Manager opens its Main Menu.
•You should probably use the Configuration Manager's Setup Wizard program if
you want to change the router's default settings. See Launching the
Configuration Manager’s Setup Wizard below.
•If you wish to use WPS to set up your wireless connection. Go to Chapter 3:
Wireless and Wireless Security Setup. (You should probably use the
Configuration Manager's Setup Wizard program first if you want to change the
router's default settings.)
•If you are experienced with networking devices and their configuration, you
can use the Advanced configuration program to tailor the router's configuration
to your needs. Go to Chapter 4: Using the Configuration Manager's
Advanced Program on page 33.
Launching the Configuration Manager's Setup Wizard
When you start the Configuration Manager (http://192.168.1.1 on your Web browser)
and log in, the ADMINISTRATOR'S MAIN MENU opens.
12 TravelRouterwithWireless-NUserManual

Click Wizard on the Toolbar to launch the Setup Wizard, which will guide you through the
configuration process.
The Setup Wizard page opens.
Each of the six Steps guides you in configuring a specific setting or group of settings.
When you click Next or Back, you move from one step to another.
Step 1. Setup Login
To view or change configuration settings, you must enter a password. Your router has
a default password (admin) that was set by the factory and that you used to access the
Configuration Manager initially. If you want to keep the default password, click Next to
skip this step. Otherwise, to safeguard your configuration, particularly if you make
changes, we recommend that you change the login password.
1On the SetupLogin Password page, type the old password in the OldPasswordfield.
2Type the new password in the New Password field.
3Type the new password in the Reconfirm field, then click Next.
Note: If you forget the new password, you won't have access to the Configuration
Manager and will need to restore the device to its factory settings, thus losing any
changes you made to your router's configuration. To avoid this problem, we
recommend that you write the new password here and also save it in some other
convenient location.
PASSWORD:______________________________________
Chapter2:UsingtheConfigurationManager 13

Please refer to Resetting the Router to the Default Configuration on page 10 or The
Reset to Default Dialog on page 58 for more information in the unlikely event that you
need to restore the router's default settings.
Step 2. Setup Time Zone
The Time Zone setting is not configured initially. You can set it to your current locale
and change it later, as needed, if you are traveling across time zones.
To set the time zone, select the time zone that applies to your locale from the
dropdown menu, then click Next.
Step 3. WAN Type Setup
The WAN Type refers to the protocol used by your Internet Service Provider in
establishing your Internet connection. By default, WAN Type is set to your Mobile
Broadband USB modem, a wireless cellular connection.
14 TravelRouterwithWireless-NUserManual

Configuring the WAN Type
When you select one of the WAN Type protocol settings and click Next, a new page
opens where you can configure the WAN Type that you chose. Please check with your
service provider if you are unsure which WAN Type to choose.
•Static IP Address - Typically you have to request and pay extra for a static IP
address.
•Configuring the Dynamic IP Address - DSL modem users who do not need
to enter a password and Cable modem users should choose this WAN type.
•PPPoE - Choose this type if your ADSL connection uses PPPoE.
•PPTP - The Point to Point Tunneling Protocol is more common in corporate
environments and most users will not use this setting.
•L2TP - The Layer 2 Tunneling Protocol is more common in corporate
environments and most users will not use this setting.
•Cellular Modem - Select this if you are using your mobile broadband modem
to connect to the Internet. (If you are using the modem as the backup to a
ADSL or Cable modem, you'll need to use the Configuration Manager's
Advanced program to configure this setup. Please refer to 3G Failover on The
Basic Setup Page on page 35.)
If you select Static IPAddress, Dynamic IP Address, PPPoE, PPTP, or L2TP, then the
Ethernet port will be set as the WAN port.
If you accept the default setting (Cellular Modem), then the Ethernet port is set as the
LAN port.
Configuring the Static IP Address
If your ISP uses Static IP addressing, select the Static IPAddress button on the Select
WAN Type menu. The following page opens:
Chapter2:UsingtheConfigurationManager 15

•LAN IPAddress
This is the LAN IPAddress of your router. Devices behind the router use this
address as their default gateway. Most users will not need to change this
address.
•Static IPAddress
This is the IP address that is given to you by your service provider when you
sign up for a Static IP address. This address identifies your Travel Router
with Wireless-N when seen from the Internet.
•Static Subnet Mask
This is the router's subnet mask. Your service provider supplies this address,
•Static Gateway
This is the IP address of the ISP server. Your service provider supplies this
address.
•Static Primary DNS
This is the Domain Name System (DNS) server's IP address. Your service
provider supplies this address.
•Static Secondary DNS
This is the IP address of an alternate Domain Name System (DNS) server.
Your service provider supplies this address.
Go to Step 4. Wireless Settings on page 21.
Configuring the Dynamic IP Address
If your service provider uses Dynamic IP addressing, select the Dynamic IPAddress
button on the Select WAN Type menu. The following page opens:
16 TravelRouterwithWireless-NUserManual

•LAN IPAddress
This is the LAN IPAddress of your router. Devices behind the router use this
address as their default gateway. Most users will not need to change this
address.
•Host Name
This is the name that identifies your Travel Router with Wireless-N . Some
service providers require a host name. Your service provider supplies this
name, if needed.
•ISP registered MACAddress
This is the 12-digit Media Access Control (MAC) address of your router.
Click the Clone button to get the MAC address that was registered with your
service provider for your device, if needed.
Go to Step 4. Wireless Settings on page 21.
Configuring PPPoE
If your ISP uses the Point-to-Point Protocol over Ethernet, for DSL-based Internet
services, you should select the PPPoE button on the Select WAN Type menu. The
following page opens:
•LAN IPAddress
This is the LAN IPAddress of your router. Devices behind your router use
this address as their default gateway. Most users will not need to change
this address.
•Account
This is the PPPoE account name supplied by your service provider.
•Password
This is PPPoE password supplied by your service provider.
Chapter2:UsingtheConfigurationManager 17

•Primary DNS
This is the Domain Name System (DNS) server's IP address. Your service
provider supplies this address, if needed.
•Secondary DNS
This is the IP address of an alternate Domain Name System (DNS) server.
Your service provider supplies this address, if needed.
•Service Name
This is the name assigned by your service provider to identify your service.
The Service Name is optional.
•Assigned IPAddress
This is the optional IP address assigned by your service provider. The
Assigned IPAddress is optional.
Go to Step 4. Wireless Settings on page 21.
Configuring PPTP
If you are using your router within a VPN, you might need to select the Point-to-Point
Tunneling Protocol (PPTP). When you select the PPTP button on the Select WAN Type
menu, the following page opens:
•LAN IPAddress
This is the LAN IPAddress of your router. Devices behind your router use
this address as their default gateway. Most users will not need to change
this address.
•IP Mode
This is the mode used to generate the IP address. Select an option from the
dropdown menu, based on your service provider's requirements.
18 TravelRouterwithWireless-NUserManual

•My IPAddress
This is the private IP address that your service provider assigned to your
router.
•My Subnet Mask
This is the private subnet mask that your service provider assigned to your
router.
•Gateway IP
This is the IP address of the service provider's server. Your service provider
supplies this address.
•Server IPAddress/Name
This is the name and IP address of the PPTP server. Your service provider
supplies this information, if needed.
•PPTP Account
This is the PPTP account name that your service provider assigned to you.
•PPTP Password
This is PPTP password that your service provider assigned to you.
Go to Step 4. Wireless Settings on page 21.
Configuring L2TP
If you are using your router within a VPN, you might need to select the L2TP menu item.
If you select the L2TP button on the Select WAN Type menu, the following page opens:
•LAN IPAddress
This is the LAN IPAddress of your router. Devices behind your router use
this address as their default gateway. Most users will not need to change
this address.
•IP Mode
This is the mode used to generate the IP address. Select an option from the
dropdown menu, based on your service provider's requirements.
Chapter2:UsingtheConfigurationManager 19

•IP Address
This is the IP address that identifies the L2TP server. Your service provider
supplies this address.
•Subnet Mask
This is the router's subnet mask. Your service provider supplies this
address.
•WAN Gateway IP
This is the WAN Gateway IP address of the L2TP server. Your service
provider supplies this address.
•Server IPAddress/Name
This is the name and IP address of the L2TP server. Your service provider
supplies this information, if needed.
•L2TP Account
This is the L2TP account name or user name supplied by your service
provider.
•L2TP Password
This is L2TP password supplied by your service provider.
Go to Step 4. Wireless Settings on page 21.
Configuring the Mobile Broadband Modem
To configure your Mobile Broadband modem, select the Cellular Modem button on the
Select WAN Type menu. The following page opens:
If you do not know the APN, Dialed Number, Account, or Password of your service
provider you should contact them or refer to Appendix A: Mobile Broadband
Settings for a list of many wireless service providers’ settings.
20 TravelRouterwithWireless-NUserManual