ZOpid HF-ZP035W User manual

3.5” DISPLAY DIGITAL PHOTO FRAME
HF-ZP035W
INSTRUCTION MANUAL
IMPORTANT: If the frame does not power on or you get dark gray screen
please connect frame to the AC adapter and RESET the frame. To reset, use
something pointy to press the RESET button which is inside the small hole right
below the USB port on the frame (see diagram on next page).
Please check our support website www.hittusa.com for FAQs and
Troubleshooting Tips.

1
PREFACE
We express our sincere thanks for purchasing this Digital Photo Frame (DPF)!
Before operating this DPF, be sure to read this user manual carefully. After
reading it, please keep it in a safe place for future reference.
We reserve the right to make changes to this DPF, Software and/or this User
Manual without notice. Please visit our company’s website listed on the
product packaging for additional product information and/or updates.
NOTE: The pictures, diagrams and certain functions described in this manual
may differ from the actual product due to different models.
PRECAUTIONS
Before operating this DPF, please read the following precautions
carefully: Do not operate this DPF in extremely cold, hot, dusty or damp
environment
Avoid putting this DPF under direct sunlight
Do not scrub this DPF with a hard item; it may result in scratches
on the screen and/or damage to the hardware
Never spray or pour liquid directly onto the screen or plastic
casing. Clean the case, LCD screen and buttons with slightly damp
soft cloth.
To avoid permanent data loss, do not insert or remove memory
card while the power is ON, or remove USB cable while pictures are
being copied to the memory card or built-in memory
Keep this DPF and all accessories out of reach of children.
BUTTONS & INTERFACE
RESET

2
1. POWER:
Press & Hold this button to turn power ON or OFF
Press & quickly release this button to toggle between Digital Clock,
Analog Clock and Calendar, while displaying clock/calendar
Press this button to pause slide show (from SD card only) – while in slide
show mode
2. LEFT:
Previous Picture (during picture display mode)
Previous Menu option or setting (during menu display and setup modes)
3. RIGHT:
Next Picture (during picture display mode)
Next Menu option or setting (during menu display and setup modes)
4. EXIT:
Press this button to stop existing operation and return to previous
function/ menu
Press this button to enable USB Connect Mode (to transfer pictures),
when the frame is connected to a computer, using USB cable
5. ENTER:
Press this button to accept menu/option selection
Press this button while in USB connect mode to exit from that mode
Press this button while displaying calendar to allow user to change date
and time
Press this button during slide show (from SD card only) to switch to
Thumbnail mode
6. SD/MMC card slot: Supports up to 8GB SD Card
7. USB Host port: Use USB Cable to connect frame to the computer to
download pictures and charge built-in rechargeable battery.
8. Stand: Use the stand to put frame on a tabletop/desk (when not in the
leather case)
9. RESET: Use something pointy to press reset button inside the small hole
below USB port

3
BASIC MENU FUNCTIONS
The MAIN MENU, as shown below will appear, when the frame power is turned
ON or connected to computer’s USB port or AC Charger:
PHOTO:
Press RIGHT’ or LEFT key to select PHOTO option from the Main
menu and then press ENTER key to confirm the selection
The frame will automatically start SLIDESHOW (from SD card if there
is one in the card slot else the pictures will be displayed from built-in
memory)
While in SLIDESHOW mode, press POWER button to pause
SLIDESHOW (Only works when pictures are displayed from SD card)
Press LEFT button to go to Previous Picture (during Photo display
mode)
Press RIGHT button to go to Next Picture(during picture display mode)
PRESS EXIT key to exit from Photo display mode
Press ENTER button during Photo display mode (from SD card only) to
switch to THUMBNAIL mode
Press RIGHT or LEFT key to select a picture and then press ENTER

4
key to display that picture on full screen (SLIDESHOW will start
automatically if Interval Time under SETUP is not set to Manual).
NOTE: The frame will display pictures from SD card if inserted in the frame. If
the card is not inserted then the frame displays pictures from the built-in
memory
NOTE: There is 32MB of built-in memory which holds about 90 pictures and
requires the include DPFMate350 software to copy pictures to the built-in
memory – Remove SD card to display pictures from the built-in memory
CLOCK:
Press RIGHT or LEFT key to highlight CLOCK Menu Option and then press
ENTER key to complete selection
Press & quickly release POWER button to toggle between Digital Clock,
Analog Clock and Calendar, while displaying clock or calendar

5
CALENDAR:
Press RIGHT or LEFT key to highlight CALENDAR Menu Option and then
press ENTER key to complete selection
NOTE: Press ENTER button while displaying calendar to Enter Date and Time
Change Mode
Once in Date and Time Change Mode YEAR starts flashing
Use LEFT or RIGHT key to change Year
Press Enter to confirm selection and move to change MONTH

6
Use LEFT or RIGHT key to change Month
Press Enter to confirm selection and move to change DAY
Use LEFT or RIGHT key to change Day
Press Enter to confirm selection and move to change HOURS
Use LEFT or RIGHT key to change Hour
Press Enter to confirm selection and move to change MINUTES
Use LEFT or RIGHT key to change Minute
Press Enter to confirm selection and move to change SECONDS
Use LEFT or RIGHT key to change Seconds
Press Enter to confirm selection and Exit from Date and Time
Change Mode
Press EXIT key to return to the Main Menu
SETUP:
Press RIGHT or LEFT key to highlight SETUP Menu Option and then press
ENTER key to complete selection.
PHOTO SETTINGS

7
INTERVAL TIME:
Press ENTER key to select Interval Time and change the time
Use RIGHT or LEFT key to select one of the following available
options: 5 Seconds, 10 Seconds, 15 Seconds, 30 Seconds, 1 Minute,
2 Minutes, Manual (select this option to disable slideshow mode)
Press ENTER key to confirm selection and move to the next SETUP
option or press EXIT key to return to the Main Menu
TRANSITION EFFECT:
Press ENTER key to select Transition Effect and change the option
Use RIGHT or LEFT key to select one of the following available
options: No Effect, random, UP DOWN, Black, Shutter 1, Shutter2, Roll,
Push UP, Fade OUT, COMB, Center, Plus, Cheese, Two lines, Four
lines, Many lines, Buttery
Press ENTER key to confirm selection and move to the next SETUP
option or press EXIT key to return to the Main Menu
BROWSE:
Press ENTER key to select Browse and change the option
Use RIGHT or LEFT key to select one of the following available
options: Panscan, Fit, Full, ORG
Press ENTER key to confirm selection and move to the next SETUP
option or press EXIT key to return to the Main Menu
DISPLAY SETTINGS
OSD LANGUAGE:

8
Press ENTER key to select OSG Language and change the option
Use RIGHT or LEFT key to select one of the following available
options: English, Chinese
Press ENTER key to confirm selection and move to the next SETUP
option or press EXIT key to return to the Main Menu
BRIGHTNESS:
Press ENTER key to select Brightness and change the option
Use RIGHT or LEFT key to select one of the following available
options: 1 to 8
Press ENTER key to confirm selection and move to the next SETUP
option or press EXIT key to return to the Main Menu
AUTO OFF:
Press ENTER key to select Auto Off and setup Hours and Minutes to
auto power off the frame
Use LEFT or RIGHT keys to change Hour
Press Enter to confirm selection and move to change MINUTES
Use LEFT or RIGHT keys to change Minutes
Press ENTER key to confirm selection and move to start from the first
SETUP option or press EXIT key to return to the Main Menu

9
E. CONNECTING FRAME TO THE COMPUTER (to charge battery, download
pictures and to display pictures without using rechargeable battery or AC
adapter)
Plug smaller end of the USB Cable into USB Port on the frame and the larger end of the
cable into USB port on the computer.
NOTE: A/C charger can also be used to supply power and charge built-in battery
CHARGE BATTERY & SUPPLY POWER FROM COMPUTER”S USB PORT :
When the USB cable is properly connected, Charging… message is displayed on the
display indicating the battery is getting charged. It can take up to 4 hours to fully
charge the battery.
Charging…
COPYING PICTURES TO THE FRAME
: Make sure the USB cable is properly
connected, and the frame screen displays the Main Menu
Press “EXIT” key to enter
USB Connect mode
to copy pictures to frame’s built-in memory or an SD Card (if
inserted in the SD Card Slot on the frame)
Connecting PC, press Enter to Exit