Zotac ZBOX PRO ZP-QK7P3000 User manual

1
ZP-QK7P3000
User’s Manual
No part of this manual, including the products and software described in it, may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language in any form or by any means, except documentation kept by the
purchaser for backup purposes, without the express written permission of ZOTAC.
Products and corporate names mentioned in this manual may be registered trademarks
or copyrights of their respective companies, and are used for identication purposes
only. All trademarks are the property of their respective owners.
Every effort has been made to ensure that the contents of this manual are correct and
up to date. However, the manufacturer makes no guarantee regarding the accuracy of
its contents, and reserves the right to make changes without prior notice.
CAUTION:
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.

2
Table of Contents
Specications ----------------------------------------------------------------------------------------------------3
Safety instructions----------------------------------------------------------------------------------------------5
Package contents -----------------------------------------------------------------------------------------------6
Getting to know your ZP-QK7P3000 ----------------------------------------------------------------------7
Front view -----------------------------------------------------------------------------------------------------7
Rear view ------------------------------------------------------------------------------------------------------8
Installing hardware inside ZP-QK7P3000 ---------------------------------------------------------------9
Installing an M.2 SSD module----------------------------------------------------------------------------10
Installing a memory module-------------------------------------------------------------------------------12
Installing a hard disk drive---------------------------------------------------------------------------------13
Installing the L-shaped mountings------------------------------------------------------------------------16
Installing your ZP-QK7P3000 to a monitor -------------------------------------------------------------17
Setting up your ZP-QK7P3000 ------------------------------------------------------------------------------18
Installing drivers and software -----------------------------------------------------------------------------20
Installing an operating system----------------------------------------------------------------------------20
Installing system drivers -----------------------------------------------------------------------------------20
Using your ZP-QK7P3000 ------------------------------------------------------------------------------------21
Conguring wireless connection -------------------------------------------------------------------------21
Conguring audio output-----------------------------------------------------------------------------------22
EDID conguration ---------------------------------------------------------------------------------------------23

3
Specications
Microprocessor Support •7th gen Intel Core i7-7700T Quad-core 2.9GHz/3.8GHz,
6MB cache, 35W TDP
Operating Systems •Support Windows 10 64-bit; Ubuntu Linux 16.04 LTS
Onboard Graphics Support •NVIDIA Quadro P3000 MXM w/6GB GDDR5
•4x HDMI2.0 (max resolution: 3840x2160 @60Hz)
System Memory Support •Two DDR4 2133/2400 SO-DIMM slots
•Up to 32 GB of memory
USB Ports •2x USB3.1
•2x USB3.0
•2x USB2.0
Onboard Serial ATA •SATA 6.0 Gb/s transfer rates
•Support one 2.5-inch SATA III HDD/SSD bay
(support the device with max 9.5mm height)
Expansion Slot •One M.2 2242/2260/2280 key-M socket for SSD
Card Reader •SD/SDHC/SDXC
Onboard Dual Gigabit LAN •Support 10/100/1000 Mbps operation
•Support IEEE 802.3
WiFi Support (optional) •802.11ac Wi-Fi (dual-band)
H/W watchdog timer •Timeout value = 1 ~ 255, Unit = minute/second
Legacy I/O •RS232 serial port
Case Dimension •227.0mm x 202.5mm x 62.5mm

4

5
Safety instructions
ZP-QK7P3000 is designed and tested to meet the latest standards of safety for information technology
equipment. However, to ensure your safety, it is important that you read the following safety instructions.
Read and follow all instructions in the documentation before you operate your system.
Do not use this product near water or a heat source such as a radiator.
Set up the system on a stable surface with the provided stand. Never use the system alone
without the stand.
Openings on the chassis are for ventilation. Do not block or cover these openings.
Make sure you leave plenty of space around the system for ventilation. Never insert objects of
any kind into the ventilation openings.
Use this product in environments with ambient temperature on below conditions:
Main unit: -20°C - +40°C
AC adapter: +0°C ~ +40°C
Do not walk on the power cord or allow anything to rest on it.
Do not spill water or any other liquids on your system.
When the system is turned off, a small amount of electrical current still ows. Always unplug all
power, modem, and network cables from the power outlets before cleaning the system.
If you encounter the following technical problems with the product, unplug the power cord and
contact a qualied service technician or your retailer.
¾The power cord or plug is damaged.
¾Liquid has been spilled into the system.
¾The system does not function properly even if you follow the operating instructions.
¾The system was dropped or the cabinet is damaged.
¾The system performance changes.

6
Package contents
Thank you for choosing our ZP-QK7P3000. The following illustration displays the package contents of
your new ZP-QK7P3000. If any of the below items is damaged or missed, contact your retailer.
• 1 x ZP-QK7P3000
• 1 x L-shaped mounting kit
• 1 x AC Adapter
• 1 x Power Cord
• 1x WiFi Antenna
• 1 x USB ash drive
• 1 x User’s manual (soft copy)

7
Getting to know your ZP-QK7P3000
Front view
1. Power button
The power button turns the system ON and OFF.
2. Power LED
The Power LED is always ON when power is on.
3. WiFi LED
The WiFi LED blinks when data is being transfered over WiFi.
4. Hard disk LED
The hard disk LED blinks when data is being written onto or read from the hard disk drive.
5. Memory card slot
The Memory card slot is compatible with SD/SDHC/SDXC cards used in devices like digital
cameras, MP3 players, mobile phones and PDAs.
6. USB 3.1 port
The USB 3.1 port supports the SuperSpeed USB 3.1 device. Use this port for USB 3.1 devices
for maximum performance with USB 3.1 compatible devices.
7. Microphone jack
The microphone jack is designed to connect a microphone for video conferencing, voice
narrations or simple audio recordings.
8. Headphone/Audio Out jack
The stereo headphone jack (3.5mm) is used to connect the system’s audio output signal to
amplied speakers or headphones.
5
234
1
6
7
6
8

8
Rear view
1. COM port
Use the COM port to connect serial devices such as mouse or fax/modem.
2. Power input (DC19.5V)
The supplied power adapter converts AC power to DC power for use with this power port. To
prevent damage to the mini-PC, always use the supplied power adapter.
3. USB 2.0 ports
The USB (Universal Serial Bus) port is compatible with USB devices such as keyboards, mice,
cameras and hard disk drives.
4. USB 3.0 ports
The USB 3.0 port supports the SuperSpeed USB 3.0 devices. Use this port for USB 3.0
devices for maximum performance with USB 3.0 compatible devices.
5. HDMI ports
The HDMI (High Denition Multimedia Interface) port supports a UHD device such as an LCD
TV or monitor to allow viewing on a larger external display.
6. COPY/ERASE
Press the COPY/ERASE button once to read, copy and proofread, press it for ve seconds to
clear the EDID EEPROM.
7. EMULATION ON
Press the EMULATION ON button once to toggle between “Emulation On” or “Pass Through”
Mode.
8. Ethernet ports
The eight-pin RJ-45 LAN port supports standard Ethernet cable for connections to local area
networks (LAN) with speeds of 10/100/1000Mbps.
9. WiFi antenna connector
The WiFi antenna connector supports the included WiFi antenna.
The power adapter may become warm to hot when in use. Do not cover the adapter and keep it away from your body.
1
23 4
5
67
8
9

9
Installing hardware inside ZP-QK7P3000
Before installing hardware, please follow the instructions below to remove the cover of your
ZP-QK7P3000.
1. Remove the four thumb screws of bottom cover.
6. Hold the bottom cover with two hands, and lift it up as shown below.

10
2. Insert an M.2 SSD module into the slot.
Installing an M.2 SSD module
1. Locate the M.2 SSD slot and remove the screw on the blot as shown below.
The M.2 SSD slot only support SATA SSD module.

11
3. Gently press down on the M.2 SSD module, and install the screw.

12
Installing a memory module
1. Insert the memory module into the socket.
2. Gently press down on the memory module until it is locked by the arms of the socket.

13
Installing a hard disk drive
1. Unscrew and remove the hard disk drive bracket as shown below.
2. Locate the 2.5-inch SATA hard disk drive and the hard disk drive bracket.

14
4. Insert the hard disk drive /SSD into the socket and gently slide into the connector.
3. Install the hard disk drive/ SSD to the hard disk drive bracket.

15
5. Reinstall the screw for the hard disk drive bracket.
5. Reinstall the bottom cover.

16
Installing the L-shaped mountings
1. Locate the bottom cover upwards, and take out the L-shaped mounting kit and screws from
accessory box.
2. Install the L-shaped mountings to the bottom cover with screws.

17
Installing your ZP-QK7P3000 to a monitor
You can also install your ZP-QK7P3000 to the back of a monitor. To do so:
1. Secure four screws (M4XH15.0MM) to your monitor ( VESA100 standard).
2. Place your ZP-QK7P3000 to the monitor noting the correct alignment.
Mechanical Loading Stability - Mounting of the equipment on the backside of the
monitor should be lay this equipment on a reliable surface when install. A drop or
fall could cause injury.


18
Setting up your ZP-QK7P3000
Please connect your peripherals before using your ZP-QK7P3000.
123456
7
12 3
45
6
7
1. Connecting a COM device
Connect serial devices such as mouse of fax/modems.
2. Connecting to USB 2.0 devices
Connect USB 2.0 devices such as keyboards, mice, cameras and hard disk drives.
3. Connecting to USB 3.0 devices
Connect USB 3.0 devices such as external hard disk drives, SSDs and ash drives to the USB
3.0 port on the system rear panel.

19
4. Connecting to HDMI displays
Connect one end of an HDMI cable to an HDTV or monitor, and the other end to the HDMI
port on the system rear panel.
5. Connecting to networks
Connect one end of a network cable to the LAN port on the system rear panel and the other
end to a network router, hub or switch.
6. Connecting the WiFi antenna
Connect the WiFi antenna to the WiFi antenna connector.
7. Connecting the power adapter and turning on the ZP-QK7P3000
Connect the supplied AC adapter to the DC IN jack on the system rear panel and then press
the power switch on the front panel to turn on the system.
When your ZP-QK7P3000 is not in use, unplug the power adapter or switch off the
AC outlet to conserve power.