ZUUM HE1LBIR232-EP-2.0-70M User manual

www.zuum.life ZM011419
8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014
HE1LBIR232-EP-2.0-70M
HDMI Cat5/6 Extender for UHD displays up to 40 meters (131’) at 4Kx2K@60Hz UHD HDR 4:4:4
Extend high-resolution HDMI up to 70 meters (229’) with this HDMI over single cat5e/cat6 extender. This extender uses HDBaseT technology
to extend uncompressed high-definition video up to 4Kx2K@60hz UHD HDR 4:4:4. This extender also supports PoH. Power over cable and
can be power from ether transmitter or receiver side.
Features:
>Extends HDMI, RS232 and IR signal over one CAT5/6 cable, (only one power supply needed)
>HDBaseT 2.0, HDMI 2.0, HDCP 2.2/1.4 & DVI Compliant
> 1080p@60 up to 229’ (70m), 4Kx2K@60Hz 4:4:4 up to 131’ (40m) ,18Gbps
> Audio supports up to LPCM 7.1 @ 192KHz, Dolby TrueHD, DTS-HD MA, DTS:X, Atmos
> Bi-directional IR, IR carrier support 30-60khz
> Bi-Directional RS232 interface – commands and data can flow in both directions via RS232, allowing status requests and control of the
destination unit.
> Bi-directional Supports CEC, EDID pass through
Panel View:

www.zuum.life ZM011419
8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014
Install Notes:
Caution: The wiring must be away from any equipment with electromagnetic signal, i.e.: mobile phone, microwave, radio
equipment, fluorescent lamp, and high voltage power lines.
Transmission Range: If connection is through a wall jack, (not recommended) this could limit the full transmission distance between
the Transmitter and Receiver Extenders. We only recommended using a straight CAT5/6 cable with RJ45 connections on each end.
Shielded Cable: On most installations it is recommended to use Shielded CAT5/6 cable with properly connected shielded RJ45
connectors. This will prevent video and audio loss due to EMI and other interference from switched lighting and ceiling fans.
HDCP 2.2 mode if any one monitor fails then all monitors will fail. All devices must support HDCP 2.2 mode.
RJ45 Connection: Do not connect HDBaseT RJ45 port to Ethernet signal, or network devices to this port to avoid damage.
LED Status:
Firmware Update Switch Function:
1. Reserved
2. FW1 updated
3. FW2 updated
4. FW3 updated
RS232 Defined:
DB9 (Male) DB9 (Female)
Color
Status
HE1BIR232-E-2.0-70M TX
HE1BIR232-E-2.0-70M RX
GREEN
LINK
ON: HDBaset Linking
BLUE
VIDEO
ON: Input signal 4Kx2K@60Hz 4:4:4
RED
FW UP
ON: Firmware Update
Color
Status
HE1BIR232-EP-2.0-70M TX
HE1BIR232-EP-2.0-70M RX
GREEN
ON
ON: Power normal
BLUE
IR RX
ON: Receiving IR signal
RED
IR TX
ON: Sending IR signal
RS232
RS232
Footprint
Define
Footprint
Define
Pin 2
TX
Pin 2
RX
Pin 3
RX
Pin 3
TX
ON######
#
1######2#####3######4#
#
#
#
#

www.zuum.life ZM011419
8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014
RJ45 Defined:
Video Link (TIA/EIA-568-B)
1. Orange-white DATA0 +
2. Orange DATA0 -
3. Green-white DATA1 +
4. Blue DATA2 +
5. Blue-white DATA2 -
6. Green DATA1 -
7. Brown-white DATA3 +
8. Brown DATA3 -
IR Control Connections:
- Example 1: When using IR remote control at TV side, plug IR receiver into HDMI Receiver Extender and plug IR into RX
meaning it will receive incoming IR commands from remote. On the source side plug IR blaster into HDMI
Transmitter Extender and plug IR into TX meaning it will blast (transmit) out IR commands to source
equipment.
- Example 2: In an example where you use an RF remote or other control system and it communicates back to an RF
receiver and then outputs IR commands to the source equipment set up as follows. Use our adapter cable
from the 3rd party IR system emitter out and go into the HDMI Transmitter Extender IR RX input. Then on the
HDMI Receiver Extender by TV you plug the IR blaster included to the IR TX port. This set up allows IR
coming out of your 3rd party system to go into the HDMI Transmitter located at source equipment and send IR
back up to TV so IR can control it as well from the 3rd party IR remote controller. You can use the additional
included cable to adapt an emitter to attach to TV if you do not want to use the included IR blaster.
If connecting to other manufacturer emitters use our IR adapter cable Model:HE1LIR35M35F-.5.
If connecting to other 3rd party IR system and coming from there system into our HDMI Transmitter IR RX input use
Model: IRADAPT-60
Note: Do not place the IR blaster near or in an area that allows the signal to affect the IR receiver. This can cause
interference and unreliable performance.
Package Contents:
- HE1LBIR232-EP-2.0-70M Transmitter x 1
- HE1LBIR232-EP-2.0-70M Receiver x 1
- Power adapter DC12V 1.5Amp x 1
- Mounting screw pack x 2
- IR Blaster cable x 1
- IR Receiver cable x 1
- IRADAPT-60 cable x 1
Pin 5
GND
Pin 5
GND

www.zuum.life ZM011419
8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014
- Product Instructions
General Specifications:
Model
HE1LBIR232-EP-2.0-70M-TX
HE1LBIR232-EP-2.0-70M-RX
HDMI Video Support
Up to 1080p@60Hz@48bits, 3D, 4Kx2K@60Hz (YCbCr 4:4:4), 18Gbps
HDMI Distance
1080p@60 up to 229’ (70m), 4Kx2K@60Hz 4:4:4 up to 100’ (30m)
HDMI Connector
Type A
HDMI Audio Support
Up to LPCM 7.1 192KHz, Dolby TrueHD, DTS-HD MA
HDBaseT Connector
RJ45 x 1
RS-232 Connector
DB9 Female
DB9 Male
RS-232 Baud Rate
Up to 115200 bps / Full Duplex
IR Connector
3.5mm Phone Jack x 2
IR Carrier
30-60KHz (2 Way)
Power Supply
Regulated 12V 1.5Amp x 1
Power Consumption
5.4W (Max)
7.32W (Max)
Dimensions
4.31” x 4.31” x 1.18”
Weight lbs.
.59
.62
Humidity
Up to 95%
Storage Temperature
-4 to 185°F
Operating Temperature
32 to 131°F

www.zuum.life ZM011419
8805 Jones Rd. Ste. C104, Houston, X 77065 * 1-888-861-7351 * www.zuummedia.com ZM 032014
Do you Need Technical Support?
ZUUM is proud to offer free technical support to ensure your product is operating correctly.
If you are experiencing difficulties setting up this product, please call us for assistance 1-888-861-7351 or visit
www.zuum.life
Here for You 24/7