ZyXEL Communications P-793H 601156 User manual

www.zyxel.com
G.SHDSL.bis Bonded Broadband
Gateway
Version 3.70
Edition 1, 03/2010
P-793H v2
DEFAULT LOGIN DETAILS
IP Address: http://192.168.1.1
Admin Password: 1234
User Password: user
Copyright 2010
ZyXEL Communications Corporation

2
Device Panels
POWER
LED ETHERNET
LED 1-4 DSL
LED 1-2 INTERNET
LED
ON/OFF RESET
POWER ETHERNET
PORT1-4
DSL
PORT
PORT
CONSOLE

P-793H v2
3
Overview
The P-793H v2 is a secure G.SHDSL.bis bonded broadband gateway.
The P-793H v2 provides high-speed Internet access or high-speed point-
to-point connections with other ZyXEL devices of the same type. The P-
793H v2 itself can act as a router or as a bridge.
See your User’s Guide for background information on all features.
The included CD provides multi-media animations that help you set up
your P-793H v2.
Hardware Connections

4
1. DSL: Use the provided Y-connector with the included telephone
cables to connect the P-793H v2’s DSL port to the telephone jacks or
wall outlets for a point-to-2point connection.
For a standard connection to your ISP or a point-to-point connection,
you can unplug one of the telephone cables from the Y-connector and
use it for your DSL connection.
2. ETHERNET: Use an Ethernet cable to connect a computer to the
ETHERNET port for initial configuration and/or Internet access.
3. POWER: Use the power adaptor provided with your P-793H v2 to
connect an appropriate power source to the POWER socket. Make
sure the power source is on.
4. Push in the POWER button. Look at the lights on the front panel.
• The POWER light blinks while your P-793H v2 starts up and stays
on once it is ready. The DSL1 and DSL2 LEDs blink while the P-
793H v2 is trying to establish a connection with the ISP and stay on
when the connection is established. The INTERNET light is on
when you are able to access the Internet and blinks when the P-
793H v2 is sending or receiving data.
• The ETHERNET light stays on if the ETHERNET port is properly
connected and blinks when there is traffic.
If any of these lights are not on, check your connections, and inspect
your cables for damage. If the lights are still off, contact your local
vendor.

P-793H v2
5
Status Page
1. In your browser, go to http://192.168.1.1.
2. Enter the default password user to go directly to the Status screen.
3. See the User’s Guide for field descriptions of the Status screen.

6
Internet Setup
You must have an account for Internet access, and you should have the
information provided by your Internet Service Provider (ISP).
1. Open your web browser, and go to http://www.zyxel.com.
Your P-793H v2 tries to detect your Internet connection. Wait for the P-
793H v2 to finish detection. If any other screens appear, follow the
directions in the screen.
If the web page opens correctly, your P-793H v2 is ready for you to use.
If the web page does not open, follow the rest of the steps. You should
have the information provided by your ISP.
2. In your browser, go to http://192.168.1.1.
3. Enter the admin password 1234 to set up your internet and wireless
connections and security settings. Click Login.

P-793H v2
7
4. When you login the for first time, it is recommended that you change
the default password. Follow the directions in this screen to do so.
5. Click Go to Wizard setup. Then, click Apply.

8
6. Click INTERNET SETUP. Wait while your P-793H v2 tries to detect
your DSL connection.
7. Follow the directions in the wizard. Do not change default settings if
your ISP did not provide information.
Troubleshooting
1. If you cannot access the web configurator using Internet Explorer in
Windows XP or Windows Server 2003, make sure you allow pop-up
windows, JavaScripts and Java permissions or set the Internet
security level lower than High in Internet Explorer (in Internet
Explorer, click Tools > Internet Options > Security > Custom
Level...). See the appendix in the User’s Guide for more information.
2. If you cannot access the Internet when your computer is connected to
the ETHERNET port, follow these steps.

P-793H v2
9
a. Check the lights on the front panel. If they are different from what is
described in Hardware Connections , make sure the P-793H v2 is
correctly connected. If the lights are still different, turn off the
device, wait a few seconds, and turn it on again.
b. Follow the steps in Internet Setup again. Make sure you enter the
correct information. For example, if your account has a user name
and password, make sure you type it correctly. In addition, if you
are not sure which encapsulation your ISP uses, contact your ISP.
c. If you are using a new Internet account, contact your ISP to make
sure it is active.
d. If you still have problems, see Troubleshooting in the User’s
Guide.
Viewing Certification(s)
• Go to www.zyxel.com.
• Select your product from the drop-downlist box on the ZyXEL home
page to go to that product's page.
• Select the certification you wish to view from this page.

10