ZyXEL Communications ZyXEL ZyWALL USG-1000 User manual

www.zyxel.com
QUICK START GUIDE
Unified Security Gateway
Firmware v2.11
Edition 1, 11/2008
DEFAULT LOGIN DETAILS
IP Address: https://192.168.1.1
Username: admin
Password: 1234
CONTENTS
ENGLISH 3
DEUTSCH 17
ESPAÑOL 31
FRANÇAIS 45
ITALIANO 59
日本語 73
РУССКИЙ 87
简体中文 101
繁體中文 115
Copyright 2008 ZyXEL Communications Corporation
C
ZyWALL USG-1000

2
Front and Rear Panels
PWR
SYS HDD
AUX
RESET
ON/OFF
P1 - P5 USB1
USB2
FANS
POWER
SOCKET
AUX CONSOLE
EXTENSION
CARD SLOT
HDD SLOT

ENGLISH
3
ENGLISH
Checking the Package Contents
Your package
should include
one of each of
the following:
• ZyWALL
• Power cord
• Rack-
mounting
kit
• RJ-45
Ethernet
cable
• RS-232
console Y-
cable
• Printed
Quick Start
Guide
• Configuration
Reference
Card
• Compact disk
(CD)

4
Rack-mounted Installation
Mount the ZyWALL in a 19-inch rack or place it on a sturdy, flat surface.
Leave 10 cm of clearance at the sides and 20 cm in the rear.
1. Align one bracket with the holes on one side of the ZyWALL and
secure it with the included bracket screws. Similarly, attach the other
bracket.
2. After attaching both mounting brackets, position the ZyWALL in the
rack by lining up the holes in the brackets with the appropriate holes
on the rack. Secure the ZyWALL to the rack with the rack-mounting
screws.

ENGLISH
5
Connecting the Hardware
Make sure that the power switch on the rear panel is turned off before
you make the hardware connections.
Internet
2
5
1
1. It is recommended that you configure the ZyWALL before using it to
protect your network. Use an Ethernet cable to connect a computer to
port 1.
2. Use another Ethernet cable(s) to connect port 2 and/or port 3to an
Ethernet jack with Internet access.
3. Use the included power cord to connect the power socket on the rear
panel to a power outlet.

6
4. Push the power switch to the on position and look at the front panel.
The PWR light turns on. The SYS light blinks during system testing
and initialization and then stays on when the system is ready.

ENGLISH
7
Web Login
1. Launch your web browser and go to http://192.168.1.1 (the ZyWALL
automatically redirects you to https://192.168.1.1).
2. Click Yes to proceed if you get a security alert or certificate screen.

8
3. Enter admin as the user name and 1234 as the password. Click
Login.
4. It is strongly recommended that you change the password. Type and
retype a new password, and click Apply.

ENGLISH
9
Installation Setup Wizard
The Status screen opens. Click the Wizard icon in the upper right
corner.
Use an installation setup wizard to connect to the Internet and register
the ZyWALL and/or activate trial services, like IDP and content filter.
Use the installation wizard only for initial configuration starting
from the default configuration.

The wizard screens
vary depending on the
encapsulation type you
use. Refer to
information provided by
your ISP and the web
help screens to know
what to enter in each
field. You can leave
fields blank if you don’t
have that information.
10
Changes you make in the installation wizard may not be applied if you
have already changed the ZyWALL’s configuration.
• INSTALLATION SETUP, ONE ISP sets up a single Internet
connection for ge2.
• INSTALLATION SETUP, TWO ISP sets up Internet connections
for ge2 and ge3.