ZyXEL Communications P-660HN-51 - User manual

www.zyxel.com
802.11n Wireless ADSL2+ 4-port
Gateway
Firmware v1.10
Edition 1, 7/2010
P-660HN-51
DEFAULT LOGIN DETAILS
IP Address: http://192.168.1.1
User Name: admin
Password: password1
Copyright 2010
ZyXEL Communications Corporation

2
Device Panels
POWER
LAN1-4
INTERNET
WPS/WLAN
DSL
RESET
LAN PORT 1-4
POWER
DSL PORT

P-660HN-51
3
Overview
The P-660HN-51 is an ADSL router with a four-port built-in Ethernet
switch and IEEE 802.11n wireless capability. The P-660HN-51 allows
wired and wireless clients to safely access the Internet. The built-in
firewall blocks unauthorized access to your network. It supports other
helpful features, including Quality of Service (QoS) which allows time-
sensitive services and applications to flow more smoothly.
Hardware Connections
This section shows you how to set up your P-660HN-51.
2
1
3

4
1. DSL: Use a telephone cable to connect your P-660HN-51’s DSL port
to a telephone jack (or to a splitter, if one is already installed).
2. LAN: Use an Ethernet cable to connect a computer to a LAN port for
initial configuration and/or Internet access.
3. POWER: Use the power adaptor provided with your P-660HN-51 to
connect an appropriate power source to the POWER socket. Make
sure the power at the outlet is on. After connecting the power adapter,
look at the lights on the front panel.
• The POWER light blinks while your P-660HN-51 starts up and then
stays on once it is ready. The DSL light turns on when the P-
660HN-51 has a DSL connection. The WPS light turns on when the
wireless LAN is ready. The INTERNET light turns on when the
gateway is able to access the Internet and will blink when the P-
660HN-51 is sending or receiving data.
• Each LAN light stays on if the corresponding LAN port is properly
connected and blinks when there is traffic.
If the POWER, DSL, or connected LAN lights are not on, please check
your connections and inspect your cables for damage. If the lights are
still off, contact technical support.

P-660HN-51
5
Set Up a Wireless Network
You can set up a wireless network using the following methods:
Using Wireless Protected Setup (WPS)
Press the WPS button on the P-660HN-51’s front panel for more than 5
seconds to turn the WPS function on.
Follow these steps to add a WPS-enabled device to the wireless network
using the WPS/WLAN button.
Place the devices you want to connect near
one another.
Press the WPS button on the P-660HN-51.
The WPS light blinks.
Press the WPS button on a compatible
device within 2 minutes of pressing the
button on the P-660HN-51.
The WPS light on the P-660HN-51 shines
steadily when connected.
1
1
2
3

6
Set Up a Wireless Network Manually
The wireless LAN on your P-660HN-51 is enabled by default. To add a
wireless client to the network, use the settings found on the bottom panel
of your P-660HN-51, which will look similar to the following example:
Configure wireless devices that you want to connect to the wireless
network to use the same wireless settings as the P-660HN-51.
The default wireless settings vary for each P-660HN-51. Refer to the
bottom panel of your device and use the provided information.
Log into the Web Configurator
Your device may already be set up for Internet access. However, you
may want or need to log on to the P-660HN-51 Web Configurator to
perform tasks:
• Configure your Internet access settings manually
• Customize the Quality of Service (QoS) and routing features
• Create firewall and web filter rules
• Edit remote management, as well as other features
1. In your browser, go to http://192.168.1.1.
SSID: ZyXEL00561
Security Mode: WPA-PSK
Pre-Shared Key: FB373BD356

P-660HN-51
7
2. Enter the default user name admin and password password1. Click
Login.
If the login screen does not open, make sure you allow web
browser pop-up windows, JavaScripts and Java
permissions. Your computer should be also set to get an IP
address automatically from a DHCP server. See the
appendices in your User’s Guide for more information.
3. A welcome screen appears showing a summary of your last login,
such as the time, number of failed login attempts, and when the
password expires. It also shows if you are logged on from an IP
address or through a console. Select Show this page next time to
see the welcome screen on your next login. Otherwise, deselect it.
Click Continue.

8
4. In the next screen to appear, you can change the login password.
This is a recommended step. To do so, enter your new password in
the New Password field. Re-type your new password in the second
field and then click Apply.
If you prefer not to change the password, leave the two fields
blank and click Skip.
We recommend you write down your new password in the space
provided below.
New Password:
_________________________

P-660HN-51
9
5. The Network Map page appears. This shows whether the P-660HN-
51 and computers/devices connected to it have Internet access.
Click on Status to display the following screen, where you can view the
P-660HN-51 device, interface and system information.

10
See your User’s Guide for how to use the rest of the Web Configurator
screens. You will need to refer to the section on how to setup the
Broadband connection if the INTERNET LED (light) remains off.
Viewing Certifications
• Go to www.zyxel.com.
• Select your product from the drop-down list box on the ZyXEL home
page to go to that product's page.
• Select the certification you wish to view from this page or click on
the Specifications tab to see the certifications list.
Customer Information Statement
The information informing the user of his and the telephone company's
rights and obligations is outlined on the following pages. This information
will be included in the final version of the manual.
1.If this equipment DL causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of service
may be required. But if advance notice isn't practical, the telephone company
will notify the customer as soon aspossible. Also you will be advised of your
right to file a complaint withthe FCC if you believe it is necessary
.
2.If you experience trouble with this equipment, you disconnect it fromthe
network until the problem has been corrected or until you are sure that the
equipment is not malfunctioning.
3.Please follow instructions for repairing if any (e.g. battery replacement
section); otherwise do not alternate or repair any parts of device except
specified.