ZyXEL Communications PMG1005-T20C User manual

1/2 Copyright © 2019 Zyxel Communications Corp. All Rights Reserved.
POWER
3
2
LAN
POWER ON
PON
1
INTERNET
2
3
1
4
Connect the power cord to the
PMG1005-T20C and press the power
button.
Make sure the LEDs are on and
check the status.
Connect a computer to the LAN
port using the yellow Ethernet
cable.
Connect the fiber optic cable to
the PON port.
Warning! To avoid possible eye
injury, do NOT look into an
operating fiber-optic module's
connector.
Red
Green
Green
Off
Off
Off
Off
(Loss of Signal)
On: Power on and system ready
Off: Power off
On: Successful GPON fiber link
Blinking: Synchronizing with OLT (fiber terminal)
On: Not receiving an optical signal. Reconnect
the fiber optic cable to the PON port.
Off: Receiving a normal optical signal
Blinking: Transmitting/Receiving data on the
Ethernet link
Green
On: Successful Ethernet link
Off: Ethernet connection is down. Reconnect
the Ethernet cable to the LAN port.
PMG1005-T20C
GPON SFU with 1-port GbE LAN
POWER
PON
LOS
LAN
Off: The fiber link is down.
Restart the PMG1005-T20C.
Blinking: Receiving a weak optical signal.
Reposition the PMG1005-T20C.
Quick Start Guide
Hardware Connections

2/2 Copyright © 201 9 Zyxel Communications Corp. All Rights Reserved.
EU Importer: Zyxel Communications A/S | Gladsaxevej 378, 2. th. 2860 Søborg, Denmark | http://www.zyxel.dk
US Importer: Zyxel Communications, Inc | 1130 North Miller Street Anaheim, CA 92806-2001 | http://www.us.zyxel.com
See the User's Guide at www.zyxel.com for more information, including customer support and safety warnings.
x2
Unit: mm
18.0~22.0
3.5~4.2
x2
18.0~22.0
2.8~3.2
2.01~2.50
4.5~5.5
Unit: mm
Tapping Screw M4x30 mm
54mm
Troubleshooting
Wall Mounting (Optional)
Configuration (Optional)
PMG1005-T20C
User Name
Password 1234
admin
Login
User Name : admin
Password : Refer to the device label
(default)
http://192.168.1.1
5
If you want to change the admin
password, see traffic statistics,
upload new firmware or reset to
the factory defaults, open a web
browser and go to http://192.168.1.1.
Enter the default User Name
(admin) and Login Password
(1234), and then click Login.
The PMG1005-T20C doesn't turn on.
- Make sure the power cable is connected, and you've pressed the power button.
- Make sure the power adaptor is connected to an appropriate power source. Make sure the power
source is turned on.
I cannot see or access the Login screen in the Web Configurator.
- Make sure your computer has an IP address in the same subnet as the PMG1005-T20C. If your
PMG1005-T20C is using the default IP address, then your computer should have an IP address from
192.168.1.2 to 192.168.1.254. See your computer help.
- Make sure you are using the correct IP address.
• The default IP address is 192.168.1.1.
• If you changed the IP address and have forgotten it, you have to reset the PMG1005-T20C to its
factory defaults.
- Make sure your Internet browser does not block pop-up windows and has JavaScript enabled.
- Make sure you have entered the User Name and Login Password correctly.
Enter the default User Name (admin) and admin Login Password (1234), and then click Login.
If you changed the default password, please enter the new password. If you cannot remember the new
password, use a pin to push the RESET button for more than 5 seconds to return the device to the
factory defaults, including admin password on the back label.
I cannot access the Internet.
- Check the hardware connections and the LED behavior. If the PON LED is off, restart the
PMG1005-T20C. Check if the fiber cable has come loose or is damaged. Contact the vendor to
replace any damaged cables.
6
1. Drill two holes at the distance of
54mm apart.
2. Insert screw anchors and screws
(not provided) into the holes.
3. Hang the PMG1005-T20C on the
screws.
Note: If problems persist, please contact your vendor or customer support.