ZyXEL Communications PMG2005-T20B User manual

1/2 Copyright © 2019 Zyxel Communications Corp. All Rights Reserved
2 3
2
3
1
LAN
POWER
4
PON
Connect the power cable to the
modem and press the power button.
Make sure the LEDs are on and
check the status.
Connect a computer to the LAN
port using the yellow Ethernet
cable.
Connect the fiber optic cable to
the PON port.
Warning! To avoid possible eye
injury, do NOT look into an
operating fiber-optic module's
connector.
Quick Start Guide
1
INTERNET
Green
Green
Green
Off
Off
Off
Off
On: Power on and system ready
Blinking: Self-testing and starting up
Off: Power off
On: Fiber connection ready
Blinking: Synchronizing with OLT (fiber terminal)
Off: Fiber connection not ready
On: IP connection ready but no traffic
Blinking: Transmitting IP traffic
Off: Internet connection not ready
Blinking: Transmitting data via LAN
Green
On: Ethernet connection ready
Off: Ethernet connection not ready
PMG2005-T20B
GPON HGU with 1-port GbE LAN
Hardware Connections
POWER
PON
INTERNET
LAN

2/2 Copyright © 2019 Zyxel Communications Corp. All Rights Reserved
EU Importer: Zyxel Communications A/S |Gladsaxevej 378, 2. th. 2860 Søborg, Denmark | http://www.zyxel.dk
US Importer: Zyxel Communications, Inc | 1130 North Miller Street Anaheim, CA 92806-2001 | http://www.us.zyxel.com
See the User's Guide at www.zyxel.com for more information, including customer support and safety warnings.
6
1. Drill two holes at the distance of
54mm apart.
2. Insert screw anchors and screws
(not provided) into the holes.
3. Hang the PMG2005-T20B on the
screws.
The PMG2005-T20B doesn't turn on.
- Make sure the power cable is connected, and you've pressed the power button.
- Make sure the power adaptor is connected to an appropriate power source. Make sure the power
source is turned on.
I cannot see or access the Login screen in the Web Configurator.
- Make sure you are using the correct IP address.
• The default IP address is 192.168.1.1.
• If you changed the IP address and have forgotten it, you have to reset the device to its factory
defaults.
- Make sure your Internet browser does not block pop-up windows and has JavaScript enabled.
- Make sure you have entered the User Name and Password correctly.
The default User Name is admin, and the default Password is 1234. If this does not work, you have to
reset the device to its factory defaults.
I cannot access the Internet.
- Check the hardware connections and the LED behavior. If the PON LED is off. Restart the Device, and
check if the optical transceiver has malfunctioned or the fiber cable has come loose or damaged.
Contact the vendor to replace any damaged cables.
- Make sure you entered your ISP account information correctly.
- Disconnect all the cables from your device and reconnect them.
54mm
Troubleshooting
Wall Mounting
Internet Setup
PMG2005-T20B
User Name
Password 1234
admin
Login
User Name : admin
Password : 1234
(default)
http://192.168.1.1
5
Open a web browser and go to
http://192.168.1.1. Enter the default
User Name (admin) and Password
(1234), and then click Login.
GPON SN: XXXXXXXXXXXXXXXX
Serial Number: SYY41WWXXXXXX
MAC Address: XXXXXXXXXXXX
Model Number: PMG2005-T20B
Power Consumption: 2.638Watt max.
Power Rating: 12V 0.5A
Powered by Delsa, The exclusive partner of Zyxel in Iran,
www.delsa.net