2gig technologies 2gig-ft1-345 User manual

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,2GIG-FT1 TEMP FLOOD SENSOR - P/N: 10008993 B- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.5000” X 11.000” - TOL. +/- 0.125”- SCALE: 1-1 - PAGE 1 OF 2- FOLDING: FOLD 4X TO FINAL SIZE: 2.125" X 2.750"- FINISH WITH LOGO SHOWING

2GIG-FT1-345

FLOOD AND TEMPERATURE DETECTOR

INSTALLATION INSTRUCTIONS

The 2GIG-FT1-345 is a fully supervised, tamper protected one-way 345 MHz

sensor. It will monitor the ambient temperature and/or will detect a wet/dry ood

condion. The sensor reports wet/dry condions and temperature to the panel.

Flood Conditions

Once the sensor probe detects the presence of water for three (3) minutes, the

integral transmier will send a wet alarm transmission to the panel. The probe will

also send a restore (dry) report when the presence of liquid is no longer detected

by the ood probe for three (3) minutes. For ood reporng the sensor requires

the installaon of the supplied external ood probe. The sensor is capable of

detecng clean or dirty fresh water, salt water, or tap water.

Temperature Conditions

Heat:

1. If the temperature is more than 95° F (35°C) for ve (5) minutes, the sensor

will send a loop 2 transmission.

2. If the temperature is less than 95°F (35°C) for ve (5) minutes, the sensor will

send a loop 2 clear.

Cold:

1. If the temperature is less than 41°F (5°C) for ve (5) minutes, the sensor will

send a loop 3 transmission.

2. In the temperature is more than 41°F (5°C) for ve (5) minutes, the sensor

will send a loop 3 clear.

Contents

Verify that the package includes the following:

•1—2GIG Flood/Temperature Sensor

•1—Sensor Mounting Plate

•1—3V Lithium Battery ( Panasonic CR15H270 uninstalled)

•3—3/8” Phillips Screws

•1—Double Stick Tape Strip

•1—Probe Mounting Plate

Installation Tools Required

•Phillips Screwdriver

Figure 1.Temperature/Flood Sensor Contents

A Double Sck Tape Strip

B Sensor Mounng Plate

C Probe Mounng Plate

D 3V Lithium Baery

EPhillips Screws (3/8”)

FFlood Probe Cord

GFlood Probe

H Transmier with Integral Temperature Sensor

Installing and Replacing Battery

Open Sensor Case as show in Figures 2 and 3.

Install or replace baery.

Figure 2. Opening Sensor Case

Grip the base of the sensor case. Place thumb on tab and push down unl sensor

case separates.

Figure 3. Separate Sensor Case

Figure 4. Installing New Baery

Installing a New Battery and System Programming

NOTE: Do not install baery unl panel is in Sensor Programming Mode.

1. Place panel in Sensor Programming mode

2. Insert baery

3. Close sensor

Replacement Battery Installation:

NOTE: If baery has been previously installed

1. Remove baery and dispose of (meeng state regulaons)

2. Wait two (2) seconds

3. Replace baery

4. Close sensor

Installing/Mounting Flood/Temperature Sensor

The 2GIG-FT1-345 Flood and Temperature Sensor includes two methods of

installaon:

1. Double Sck Tape Installaon (See Figure 5).

2. Screw/Mounng Plate Installaon (See Figure 6).

It is strongly recommended that the Flood/Temperature Sensor be mounted using

screws (provided) and Mounng Plate (provided).

Figure 5. Double Sck Tape Mounng Sensor Mounng Plate

1. PUSH DOWN ON

THUMB TA B.

2. PULL BACK PLATE

OFF OF COVER

BATTERY REMOVAL

AND/OR INSTALLATION

BATTERY

TEMPERATURE/

FLOOD SENSOR

BASE

REMOVE SENSOR

COVER FROM

SENSOR BASE

MOUNTING

PLATE

DOUBLE

STICK

TAPE

STRIP

FLOOD/

TEMPERATURE

SENSOR

FIRST

PUSH

SENSOR

ONTO

MOUNTING

PLATE

TABS

THEN PUSH

APPLY DOUBLE STICK

TAPE TO BACK OF

MOUNTING PLATE

WALL

Figure 6. Screw Mounng Sensor Mounng Plate

Removing Flood/Temperature Sensor from Mounting Plate

If Flood/Temperature Sensor needs to be removed from the wall (for changing out

baery), open sensor case (See Figures 2 and 3). Remove baery, then Press Down

on release tab with athead screwdriver and pull sensor UP.

Figure 7. Removing Sensor from Wall/Mounng Plate

Mounting Flood Probe

The Flood Probe must be mounted at oor level using the Probe Mounng Plate

and screw (included) mount as shown in Figure 8.

Figure 8. Mounng Probe Mounng Plate at Floor Line

Flood/Temperature Speciﬁcations

Operang Temperature: 32°to 120°F (0°to 49°C)

Operang Rel. Humidity: 5 to 95%, non-condensing

Operang Frequency: 345 MHz

Baery Type: CR2 3V lithium baery

Projected Baery Life: 5 Years

Supervisory Interval 70 Minutes

REGULATORY INFORMATION

This equipment has been tested and found to comply with the limits for Class B Digital

Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protecon against harmful interference in a residenal installaon. This equipment generates

and can radiate radio frequency energy and, if not installed and used in accordance with the

instrucons, may cause harmful interference to radio communicaons. However, there is

no guarantee that interference will not occur in a parcular installaon. If this equipment

does cause harmful interference to radio or television recepon, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures.

Reorient or relocate the receiving antenna

Increase the separaon between the equipment and receiver

Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected

Consult the dealer or an experienced radio/TV technician for help.

Any changes or modicaons not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils

radio exempts de licence. Ľexploitaon est autorisée aux deux condions suivantes: (1)

ľappareil ne doit pas produire de brouillage, et (2) ľulisateur de ľappareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est suscepble ďen compromere le

fonconnement.

FCC COMPLIANCE STATEMENT

This device complies with FCC Rules and Regulaons as Part 15 devices as well as Industry

Canada license exempt RSS Rules and Regulaons. Operaon is subject to the following two

(2) condions: This device may not cause harmful interference. This device must accept any

interference received, including interference that may cause undesired operaon.

LIMITED WARRANTY

This Nortek Security & Control LLC product is warranted against defects in material and

workmanship for two (2) years. This warranty extends only to wholesale customers who

buy direct from Nortek Security & Control LLC or through Nortek Security & Control normal

distribuon channels. Nortek Security & Control does not warrant this product to consumers.

Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty,

if any.

There are no obligaons or liabilies on the part of Nortek Security & Control for consequenal

damages arising out of or in connecon with use or performance of this product or other

indirect damages with respect to loss of property, revenue, or prot, or cost of removal,

installaon, or reinstallaon. All implied warranes for funconality, are valid only unl the

warranty expires. This Nortek Security &Control Warranty is in lieu of all other warranes

expressed or implied.

Nortek Security & Control LLC

1950 Camino Vida Roble, Suite 150

Carlsbad, CA 92008-6517 USA

For technical support in the USA and Canada:

855-2GIG-TECH (855-244-4832)

Email: 2gigtechsupport@nortek.com

Visit www.nortekcontrol.com for technical support hours of operaon

For technical support outside of the USA and Canada:

Visit dealer.2gig.com for a list of distributors in your region

10008993 B

SENSOR

MOUNTING

PLATE

FIRST

PUSH

SENSOR

ONTO

MOUNTING

PLATE

TABS

THEN PUSH

MOUNT SENSOR

MOUNTING PLATE

WITH SCREWS (INCLUDED)

WALL

MOUNT FLOOD

PROBE MOUNTING

PLATE AT FLOOR LINE

FLOOD PROBE

SCREW FASTENER

INSTALL FLOOD

PROBE TO MOUNTING

PLATE UNTIL IT “SNAPS

”

INTO THE SIDE CLIP

SIDE CLIP

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,2GIG-FT1 TEMP FLOOD SENSOR - P/N: 10008993 B- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.5000” X 11.000” - TOL. +/- 0.125”- SCALE: 1-1 - PAGE 2 OF 2- FOLDING: FOLD 4X TO FINAL SIZE: 2.125" X 2.750"- FINISH WITH LOGO SHOWING

2GIG Flood & Temperature Control I Instrucon Manual

OPEN SENSOR

CASE AND REMOVE

BATTERY

PRESS DOWN ON

TAB IN UPPER LEFT

CORNER WITH FLATHEAD

SCREWDRIVER

THEN PUSH UP ON

SENSOR CASE TO REMOVE

Other 2gig Technologies Security Sensor manuals