3dsimo MINI User manual

MINI MANUAL

Instructions for use
3D SIMO MINI

Content:
3D SIMO MINI
Introduction of 3Dsimo mini
The content of the packaged product
Basic description of the 3Dsimo mini
Mobile APP
Procedure for operating and replacing
3Dsimo mini extensions
Maintenance
Warning
Specifications
Certification
Claims
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

of 3Dsimo mini
1. Introduction
You have got your hands on a pocket
workshop. This is the 3Dsimo mini, which
includes replaceable extensions (3D
drawing, welding, cutting, burning). Each
extension has logic for its detection and
a setup of all parameters so that you only
need to insert the extension.
The 3Dsimo mini communicates with a
mobile device using its own APP. It oers
a lot of instructional videos, templates,
but also the option of setting custom
material profiles. It’s OK if you don’t have a
smartphone; the 3Dsimo mini is equipped
with an LED display that shines through the
plastic wall.

1.
All the information needed to operate
this device can be found on the following
pages.
If you need inspiration or are having issues,
visit our website:
Before using the 3Dsimo mini, please read
the instructions carefully and pay attention
to warnings.
Strong recommendation from the
manufacturer:

packaged product
2. The content of the
1 mini 3Dsimo with 3D drawing extension
1 connecting extension
1 burning extension
1 cutting extension
1 Adapter + USB cable
1 15m of the drawing filament
1 agent for removing a jammed filament
3 Resistance wire
The packaged product includes the
following components:

ABS
1)
2)
3)
4)
5) 6)
7)
8)
9)

of 3dsimo mini
3. Basic description
Material/temperature selection buttons
(depending on the chosen extension)
1.
The buttons used for inserting / ejecting
/ heating (depending on the chosen
extension)
2.
USB power connector
3.
Magnetic contacts for attaching
accessories
4.
Contact for power pack and other
accessories
5.
Opening for cutting jammed filament
6.
Plug-in mechanism
7.

3.
AB S
1 2
3
4
5

Mobile App
4.
The Mobile App can be downloaded for
Android, IOS, Win.
iOS
Android
Windows

and replacing
extensions with the
3Dsimo mini
After connecting the adapter into a
wall outlet and the USB connector, the
text saying 3D pen will be displayed
on the LED display and then the
specification of what extension you
should insert in the 3Dsimo mini. If you
do not have any extension inserted, the
text UNSPECIFIED will appear.
1.
Always insert the extension to the
stop (Fig. 4). (The extension is not
recognized when not inserted to the
stop!)
2.
5.

5.

After inserting this extension, the text 3D
tool appears, followed by the choice of
material. After selecting the desired
material, the text HEATING is displayed.
After reaching the appropriate
temperature (2-3min), READY is
displayed. Now the feeder mechanism
is already activated and you can insert
the filament of the 3Dsimo mini (Note:
Always insert a straightened filament,
which has a blunt end as in Fig. 5).
3. 3D DRAWING
5.

insert the filament into the rear
opening and press the forward button
(Figure No. 6); at the same time you
need to gently push the string to get it
into he feed mechanism. Then it takes
approximately 10 seconds before
the wire reaches the nozzle and
the material starts flowing from the
3Dsimo mini.
3. A) INSERTING THE FILAMENT:
5.

3. B) SPECIAL FEATURE
After pressing both buttons
simultaneously for at least 2-3 sec.,
continuous extrusion will be activated
5.

(Fig. no. 7). To disable this feature,
press any front button.
2-3s
5.

Pressing the button for reverse running
and hold it until the entire string comes
out. Then, remove the string and insert
another one with a flat end (Fig. No.
8). (Remove the filament only after
warming up the 3Dsimo mini and
activating the feed mechanism!)
3. C) REPLACEMENT AND
REMOVAL OF THE FILAMENT:
5.

After inserting any extension, you’ll see
its name on the display and then the
temperature indicated in percentages.
100% corresponds to 480°C.
For preheating it is required to hold
the front button. To enable continuous
preheating, press both front buttons
simultaneously for at least 2-3 sec.
(Figure No. 7).
4. EXTENSIONS FOR WELDING,
CUTTING AND BURNING:
5.

For proper replacement, refer to Figure
No 9. It is always necessary to carefully
tighten everything! (Replacement
of tips can only be carried out after
cooling!)
5. REPLACEMENT OF TIPS
AND EXTENSIONS FOR
BURNING AND CUTTING:
5.

For proper replacement refer to Figure
No. 10.
6. FITTING AND REPLACING
THE RESISTANCE WIRE FOR
THE CUTTING EXTENSION:
5.