3M Digital Projector WX66 Operating manual

Digital Projector WX66
Product Safety Guide
WX66 Projecteur numérique - Guide de Sécurité de Produit
WX66 Digitalprojektor - Sicherheitsanleitung des Geräts
WX66 Proyector digital - Guiá de Seguridad del Producto
WX66 Proiettore digitale - Guida di Sicurezza del Prodotto
WX66 Digitale Projector - Veiligheidsgids op Product
WX66 Projector Digital - Guia da Segurança de Produto
WX66 Digital projektor - Bruksanvisning för Produktsäkerhets
WX66 数码投影机 - 产品安全指南
WX66 디지털 프로젝터 - 제품 안전 가이드
WX66 Digitaalinen projektori - Laitteen turvaohjeet

3M™ Digital Projector WX66 Product Safety Guide
2 © 3M 2008. All rights reserved.
Table of Contents
ENGLISH
Safety Information ........................................................................................................................................5
Product Safety Labels ...................................................................................................................................9
Lamp ...........................................................................................................................................................10
Remote control.............................................................................................................................................13
3M™ Digital Projector Limited Warranty ..................................................................................................14
FRANÇAIS
Mesures de sécurité......................................................................................................................................16
Autocollants de sécurité sur le produit.........................................................................................................20
Lampe ..........................................................................................................................................................21
Télécommande.............................................................................................................................................24
3M™ Projecteur Numérique Garantie Limitée ...........................................................................................25
DEUTSCH
Sicherheitsanweisungen...............................................................................................................................27
Sicherheitsaufkleber.....................................................................................................................................31
Lampe ..........................................................................................................................................................32
Fernbedienung..............................................................................................................................................35
Beschränkte Gewährleistung für 3M™ Digitalprojektor.............................................................................36
ESPAÑOL
Infomación de seguridad..............................................................................................................................38
Etiquetas de seguridad del producto ...........................................................................................................42
Lámpara .......................................................................................................................................................43
Control remote .............................................................................................................................................46
Garantía limitada del Proyector Digital 3M™.............................................................................................47
ITALIANO
Informazioni sulla sicurezza ........................................................................................................................49
Etichette di sicurezza del prodotto...............................................................................................................53
Lampada.......................................................................................................................................................54
Telecomando ................................................................................................................................................57
Proiettore digitale 3M™ garanzia limitata...................................................................................................58
NEDERLANDS
Veiligheidsinformatie...................................................................................................................................60
Veiligheidslabels ..........................................................................................................................................64
Lamp ............................................................................................................................................................65
Afstandsbediening........................................................................................................................................68
3M™ Digitale Projector Beperkte Garantie ................................................................................................69
PORTUGUÊS
Informações sobre Segurança ......................................................................................................................71
Etiquetas de Segurança do Produto..............................................................................................................75
Lâmpada.......................................................................................................................................................76
Controlo remoto...........................................................................................................................................79
Garantia Limitada do Projector Digital 3M™ ............................................................................................80
SVENSKA
Säkerhetsinformation ...................................................................................................................................82
Produktsäkerhetsetiketter.............................................................................................................................86
Lampan ........................................................................................................................................................87
Fjärrkontroll .................................................................................................................................................90
3M™ Digital projektor Begränsad garanti ..................................................................................................91

3M™ Digital Projector WX66 Product Safety Guide 3© 3M 2008. All rights reserved.
Table of Contents
中文
安全信息......................................................................................................................................................93
产品安全标签..............................................................................................................................................97
灯泡..............................................................................................................................................................98
遥控器........................................................................................................................................................101
3MTM 数码投影机有限保修 .......................................................................................................................102
한국어
안전 정보 ..................................................................................................................................................104
상품 안전 라벨.........................................................................................................................................108
램프............................................................................................................................................................109
리모컨........................................................................................................................................................112
3M ™ 디지털 프로젝터 유한 보증.......................................................................................................113
SUOMI
Tietoja turvallisuutta varten .......................................................................................................................115
Laitteen turvakyltit.....................................................................................................................................119
Lamppu ......................................................................................................................................................120
Kaukosäädin...............................................................................................................................................123
3M™ Digitaalisen projektorin rajoitettu takuu..........................................................................................124
中 文 ENGLISH
FRANÇAIS
DEUTSCHESPAÑOL
ITALIANO
NEDERLANDS
PORTUGUÊS
SVENSKA
한국어
SUOMI

3M™ Digital Projector WX66 Product Safety Guide
4
ENGLISH
© 3M 2008. All rights reserved.

3M™ Digital Projector WX66 Product Safety Guide 5
ENGLISH
© 3M 2008. All rights reserved.
Safety Information
Read, understand, and follow all safety information contained in the
“Product Safety Guide” and in the “Operator’s Guide” prior to us-
ing the WX66 Digital Projector. Service personnel must also read and
understand the safety information contained in the “Service Manual”.
Retain these instructions for future reference.
Intended Use
The 3M™ Digital Projectors are designed, built, and tested for use indoors, using 3M lamps,
3M ceiling mount hardware, and common line voltages (100V to 240V AC, 50/60 Hz).
The use of other replacement lamps, outdoor operation, or different voltages has not been
tested and could damage the projector, peripheral equipment and/or create a potentially
unsafe operating condition.
3M Digital Projectors are designed to operate in a normal ofce environment.
100V - 240V AC, 50/60 Hz
16° to 29° C (60° to 85° F)
10-80% RH (without condensation)
0-1828m (0-6000 feet) above sea level
The ambient operating environment should be free of airborne smoke, grease, oil and other
contaminates that can effect the operation or performance of the projector.
Explanation of Signal Words and Symbols in Safety Labels and Instructions
WARNING : Indicates a potentially hazardous situation, which if not
avoided, could result in death or serious injury.
CAUTION : Indicates a potentially hazardous situation, which if not
avoided, may result in minor or moderate injury.
Warning : Hazardous Voltage
Warning : Hazardous High Temperature
Warning : High Pressure
Attention : Refer to Safety Instructions in Guides

3M™ Digital Projector WX66 Product Safety Guide
6
ENGLISH
© 3M 2008. All rights reserved.
• To reduce the risk associated with choking:
- Keep the battery away from children and pets.
• To reduce the risk associated with exposure to hazardous voltage:
- Disconnect power cord when the projector is not in use, during lamp
replacement, and while cleaning.
- Do not remove any screws other than those specied in the lamp replacement
instructions.
- Do not store or operate this projector in wet environments.
- Do not modify this projector.
- Do not attempt to service the projector - there are no user serviceable parts,
other than the lamp cartridge, inside the projector. Contact a 3M authorized
service provider for service.
- Do not allow water or other liquids to enter the projector.
• To reduce the risk associated with environmental contamination due to
mercury in the projection lamp:
-
Dispose of lamp cartridge in accordance with applicable federal, state and local regulations.
- The lamp in this product contains mercury. Dispose of projection lamp in a manner
that is consistent with your local hazardous waste regulations for mercury.
- For recycling and disposal information, contact your respective governmental
agencies.
In U.S., contact 1-800-328-1371 (3M US) or the Electronic Industries Alliance at
www.lamprecycle.org
In Canada, contact 1-800-364-3577 (3M Canada)
• To reduce the risk associated with exposure to hazardous voltage and/or re:
- Replace power cord if damaged.
- Contact a 3M authorized service provider if the projector becomes damaged.
- Use a grounded extension cord with a rating at least equal to that of the projector.
- Connect this projector to a grounded outlet.
• To reduce the risk associated with hazardous voltage, impact, tripping, and
intense visible light:
- Do not use this projector around unsupervised children.
• To reduce the risk associated with hot surface of lamp cartridge:
- Unplug the projector from the electrical outlet and allow the lamp to cool for 45
minutes before replacing the lamp.
• To reduce the risk associated with a ruptured lamp:
- Always handle the fragile lamp module with care.
- Remove the projector from the ceiling or wall mount before replacing the lamp.
- Use care when replacing the lamp module in the event of a lamp rupture - small
glass particles and small amounts of mercury may be present.
- Ventilate the area where the lamp rupture occurred.
- Wear safety goggles and gloves when cleaning up ruptured lamp debris.
- Carefully collect the ruptured lamp debris in a closed container and dispose of
the container and the expired lamp module in accordance with federal, state,
and local regulations.
- Wash your hands thoroughly after handling ruptured lamp debris.
- Replace the lamp module when the lamp replacement message appears.
- Never replace the lamp module with a previously used lamp module.
WARNING

3M™ Digital Projector WX66 Product Safety Guide 7
ENGLISH
© 3M 2008. All rights reserved.
CAUTION
• To reduce the risk associated with environmental contamination:
- Dispose of exhausted batteries in accordance with applicable federal, state, and
local regulations.
• To reduce the risk associated with explosion, and/or chemicals from a leaking
batteries:
- Use only with battery type AA (HITACHI MAXELL Part No.LR6 or R6P).
- Orient the battery's plus (+) and minus (-) terminals of the batteries according to
the markings found on the remote control or internal clock battery case.
- Do not leave the battery in the remote for an extended period of time.
- Do not heat, disassemble, short, recharge, or expose to re or high temperature.
- Do not carry batteries loose in your pocket or purse.
- Avoid eye and skin contact in the event that battery would leak.
- Do not mix used and new batteries.
-Obey the local laws on disposing the battery.
• To reduce the risk associated with the impact of a falling projector:
- Use only the 3M™ brand wall/ceiling mounting hardware kit if wall or ceiling
mounting is desired.
- Installation of the 3M™ wall/ceiling kit must only be performed by qualied personnel.
- Adhere strictly to the proper installation procedure as outlined in the installation
instructions when installing the 3M™ wall/ceiling kit.
- Always operate the unit on a at, sturdy, and horizontal surface.
• To reduce the risk associated with intense visible light:
- Avoid looking directly into the projector lens while the lamp is on.
• To reduce the risk associated with tripping and/or impact:
- Position the power cord and data cable so that they cannot be tripped over.

3M™ Digital Projector WX66 Product Safety Guide
8
ENGLISH
© 3M 2008. All rights reserved.
Important Note
1. Always open the lens shutter or remove lens cap when the projection lamp is on.
2. To avoid premature lamp failure, do not change the mounting position of the
projector (desktop ceiling mount or ceiling desktop mount) and continue to use the
same lamp.
3. To avoid reduced lamp life, do not touch projection lamp with bare ngers.
4. To avoid reduced image quality, do not touch projection lens or other internal
optical components.
5. Do not use detergents, chemicals, or any spray liquids for cleaning this unit, other
than those referred to in the “Operator's Guide”.
6. For maximum lamp life, do not strike or drop, improperly handle, or scratch the
lamp glass. Also, do not install an old or used lamp.
7. Keep air lter clean. Refer to the cleaning instructions contained in the “Operator’s
Guide”.
8. Keep all ventilation openings free of any obstructions.
9. In some countries, the line voltage is NOT stable. This projector is designed to
operate safely within a bandwidth of 100 to 120 volts / 220 to 240 volts (50 to 60
Hz) ±10%, but could fail if power drops or surges of ±10 volts occur. In these high-
risk areas, it is recommended to install a power stabilizer unit.
10. Do not block intake or exhaust air vents. This will cause the projector to over heat
and shut down.
11. Do not place the projector in direct sunlight or near a hot object such as a heater.
12. To prevent damaging the projector, always hold the projector whenever using the
elevator buttons to adjust the elevator feet.
13. Use the accessory cable or a designated-type cable for the connection. Some
cables have to be used with core set. A too long cable may cause certain picture
degradation. Please consult with your dealer for details. For cables that have a
core only at one end, connect the core to the projector.
14. Make sure that you connect devices to the correct port. Incorrect connection may
result in malfunction and/or damage to the device and/or projector.
15. Do not place the projector in the side/front/rear-up position, except care of the air
lter.
16. The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE). The mark indicates the
requirement NOT to dispose the equipment including any spent or
discarded batteries or accumulators as unsorted municipal waste,
but use the return and collection systems available. If the batteries or
accumulators included with this equipment, display the chemical symbol Hg, Cd, or
Pb, then it means that the battery has a heavy metal content of more than 0.0005%
Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.

3M™ Digital Projector WX66 Product Safety Guide 9
ENGLISH
© 3M 2008. All rights reserved.
Product Safety Labels

3M™ Digital Projector WX66 Product Safety Guide
10
ENGLISH
© 3M 2008. All rights reserved.
Lamp
Lamp Operation:
The following symptoms may indicate a lamp in need of replacement:
• LAMP indicator lights up red.
• To reduce the risk associated with environmental contamination due to
mercury in the projection lamp:
-
Dispose of lamp cartridge in accordance with applicable federal, state and local regulations.
- The lamp in this product contains mercury. Dispose of projection lamp in a manner
that is consistent with your local hazardous waste regulations for mercury.
- For recycling and disposal information, contact your respective governmental
agencies.
In U.S., contact 1-800-328-1371 (3M US) or the Electronic Industries Alliance at
www.lamprecycle.org
In Canada, contact 1-800-364-3577 (3M Canada)
WARNING
Display Lamp Operation Hours
To determine the lamp operation hours, follow these steps:
1. While the projector is running, press the MENU button on the remote control.
Choose the “OPTION” using the ▼ button, and press the ► button or the ENTER button.
Choose the “LAMP TIME” using the ▼ button.
2. The operating time of the lamp will be displayed.
The lamp time is the time counted after the last resetting.
√ Note
Please reset the lamp time only when you have replaced the lamp, for a suitable
indication of elapsed lamp time.
Reset Lamp Hours
(1) Press the MENU button to display a menu. Only when the EASY MENU has appeared,
please perform the next step (2).
(2) Point at the “Go To Advance Menu …” in the menu using ▼/▲ button, then press the
► button.
(3) Point at the “OPTION” in the left column of the menu using ▼/▲ button, then press
the ► button.
(4) Point at the ”LAMP TIME” using ▼/▲ button, then press the ► button. A dialog will
appear.
(5) Press the ▲ button to select “RESET” on the dialog. This resets the lamp time.

3M™ Digital Projector WX66 Product Safety Guide 11
ENGLISH
© 3M 2008. All rights reserved.
• To reduce the risk associated with exposure to hazardous voltage:
- Disconnect power cord when the projector is not in use, during lamp replacement,
and while cleaning.
-
Do not remove any screws other than those specied in the lamp replacement instructions.
- Do not attempt to service the projector - there are no user serviceable parts, other
than the lamp cartridge, inside the projector. Contact a 3M authorized service
provider for service.
• To reduce the risk associated with hot surface of lamp cartridge:
- Unplug the projector from the electrical outlet and allow the lamp to cool for 45
minutes before replacing the lamp.
• To reduce the risk associated with a ruptured lamp:
- Always handle the fragile lamp module with care.
- Remove the projector from the ceiling or wall mount before replacing the lamp. In
the case of a lamp rupture, small glass particles could fall out when the lamp door
is opened or the projector is tilted.
- Use care when replacing the lamp module in the event of a lamp rupture - small
glass particles and small amounts of mercury may be present.
- Ventilate the area where the lamp rupture occurred.
- Wear safety goggles and gloves when cleaning up ruptured lamp debris.
- Carefully collect the ruptured lamp debris in a closed container and dispose of
the container and the expired lamp module in accordance with federal, state, and
local regulations.
- Wash your hands thoroughly after handling ruptured lamp debris.
- Replace the lamp module when the lamp replacement message appears.
- Never replace the lamp module with a previously used lamp module.
• To reduce the risk associated with environmental contamination due to
mercury in the projection lamp:
-
Dispose of lamp cartridge in accordance with applicable federal, state and local regulations.
- The lamp in this product contains mercury. Dispose of projection lamp in a manner
that is consistent with your local hazardous waste regulations for mercury.
- For recycling and disposal information, contact your respective governmental
agencies.
In U.S., contact 1-800-328-1371 (3M US) or the Electronic Industries Alliance at
www.lamprecycle.org
In Canada, contact 1-800-364-3577 (3M Canada)
WARNING
The glass lamp used in this projector contains small amounts of mercury and operates at
high pressure and at high temperature and may unexpectedly shatter. Each lamp has a
different lifetime and can fail in different ways, including a rupture with a loud bang or
simply burn out. In the event of a lamp rupture, be sure to follow the instructions.
Replacing Lamp
Important Note:
If the lamp breaks soon after the rst time it is used, it is possible that there are electrical problems
elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

3M™ Digital Projector WX66 Product Safety Guide
12
ENGLISH
© 3M 2008. All rights reserved.
√ Note
Reset the lamp operation hours. See “Reset Lamp Hours” for details.
3. Remove lamp module: Slowly pick up the lamp module by the handles. (4)
4. Insert lamp module : Carefully insert (4) the new lamp module. Ensure that it is fully seated.
Tighten the lamp module retaining screws (3) to secure the lamp module
in place.
Optional Lamp: 78-6969-9947-9 (DT00911) (Contact 3M Customer Service.)
While putting the interlocking parts of the lamp door and the projector together, slide
the lamp door back in place.(2) Then rmly fasten the screw of the lamp door.(1)
√ Note
For maximum lamp life, do not strike or drop, improperly handle, or scratch the lamp glass.
Also, do not install an old or previously used lamp.
1. Remove lamp access door:
Loosen the screw (marked by arrow) (1) of the lamp door and
then slide and lift the lamp door to the side to remove it. (2)
2. Retaining screws : Use a screwdriver to unscrew the lamp module retaining screws
(marked by arrow). (3)
√ Note
All lamp module screws must be loosened. These screws are self-containing screws that
cannot be removed from the lamp module or access door.
(2) Lamp access door
(1) Screw
(4) Handle
(3) Screws

3M™ Digital Projector WX66 Product Safety Guide 13
ENGLISH
© 3M 2008. All rights reserved.
Installing the batteries
Please load the batteries before using the remote control. If the remote control starts to malfunction, replace
the batteries. If you will not use the remote control for an extended period, remove the batteries from the
remote control and store them in a safe place.
1. Slide back and remove the battery cover in the
direction of the arrow.
2. Align and insert the two AA batteries
(HITACHI
MAXELL Part No.LR6 or R6P)
according to
their plus and minus terminals as indicated in the
remote control.
3. Replace the battery cover in the direction of the
arrow and snap it back into place.
Remote control
WARNING
CAUTION
• To reduce the risk associated with choking:
- Keep the battery away from children and pets.
• To reduce the risk associated with environmental contamination:
- Dispose of exhausted batteries in accordance with applicable federal, state, and
local regulations.
• To reduce the risk associated with explosion, and/or chemicals from a leaking
batteries:
- Use only with battery type AA (HITACHI MAXELL Part No.LR6 or R6P).
- Orient the battery's plus (+) and minus (-) terminals of the batteries according to
the markings found on the remote control or internal clock battery case.
- Do not leave the battery in the remote for an extended period of time.
- Do not heat, disassemble, short, recharge, or expose to re or high temperature.
- Do not carry batteries loose in your pocket or purse.
- Avoid eye and skin contact in the event that battery would leak.
- Do not mix used and new batteries.
-Obey the local laws on disposing the battery.

3M™ Digital Projector WX66 Product Safety Guide
14
ENGLISH
© 3M 2008. All rights reserved.
3M™ Digital Projector Limited Warranty
Warranty; Limited Remedy; Limited Liability
This product will be free from defects in material and manufacture for a period of three years from the date of purchase or for
2500 hours of use, whichever occurs rst. 3M MAKES NO OTHER WARRANTIES or CONDITIONS INCLUDING, BUT
NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at
3M’s option, to replace or repair the 3M product or to refund the purchase price of the 3M product. All replaced parts or products
become property of 3M. If the product is repaired, 3M will repair the defective part(s) with a new or used part(s). If the product is
replaced, 3M will replace the product with the same or equivalent model and with a new or refurbished product. The replacement
product carries the original equipment warranty.
Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising
from this 3M product, regardless of the legal theory asserted. Please see the following warranty limitations and exclusions.
Warranty Limitations and Exclusions
The following limitations and exclusions apply to the above mentioned limited warranty:
(a) The above warranty is limited to the 3M Digital Projector and excludes the lamp and accessories.
(b) The original lamp has the following limited warranty: 90 days from the date of purchase or 180 hours of
lamp use, whichever occurs rst.
(c) 3M Digital Projectors are designed to operate in the typical indoor environment. The product Limited
Warranty is void if used outside of the following circumstances:
• 100V-240V AC, 50/60 Hz
• 16° to 29° C (60° to 85° F)
• 10-80% RH (without condensation)
• 0-1828m (0-6000 feet) above sea level
(d) The Air Intake and Exhaust Vent must be clear of obstructions, including any potential blockage or
obstructions caused from a ceiling or other mount. Inadequate air ventilation will cause the projector to
malfunction or will cause damage to the projector which will void the warranty.
(e) The Warranty will be void if someone other than 3M (or a 3M Authorized Service Provider) repairs or
modies the 3M product.
(f) The Warranty does not cover damage due to misuse, neglect, mishandling, abuse, or normal wear and tear.
(g) The Warranty does not cover any additional costs including, but not limited to, those associated with
removal, cleaning or installation of the product, adjustments, (mechanical or electronic), made to the product
or replacing customer replaceable parts like lamps and air lters.
(h) The Warranty does not cover shipping charges incurred when returning the product to 3M for repair.
For warranty support, please call or write your local 3M office or a 3M Authorized Service Provider to obtain an RMA # (Return
Material Authorization Number) before returning the product. If you are inside the Continental United States of America,
please contact 3M Customer Service at 800-328-1371 or email [email protected].
To ensure you do not void your warranty, please review the Intended Use for Digital Projectors.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be
reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it
is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to
the product which are not contained in 3M’s current publication, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized ofcer of 3M.

3M™ Digital Projector WX66 Product Safety Guide 15
ENGLISH
© 3M 2008. All rights reserved.
FCC STATEMENT - CLASS B: This equipment generates, uses and can radiate radio frequency energy, and if not installed and
used in accordance with the instruction manual may cause interference to radio communications. It has been tested and found to
comply with the limits for a Class “B” computing device pursuant to Subpart B of Part 15 of the FCC Rules, which are designed
to provide reasonable protection against such interference when operated in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
WARNING: In the US This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC equipment provided that the following
conditions are met. The cables may have to be used with the core set to the projector side. Use the cables which are included with
the projector or specied.
Note: Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro
Magnetic Compatibility) and fullls these requirements.
•
This machine was tested against the 2006/95/EC (European Economic Community) for LVD (Low Voltage Directive) and fullls these requirements.
• This product is compliant with EU Directive 2004/108/EC (Restriction of Hazardous Substances in Electrical and Electronic
Equipment), as amended by Commission Decision 2005/618/EC on maximum concentration values.
• This product is compliant with EU Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).
Video Signal Cables: Double shielded coaxial cables (FCC shield cable) must be used and the outer shield must be connected
to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the
interference noise radiation.
Video Inputs: The input signal amplitude must not exceed the specied level.
PATENTS, TRADEMARKS & COPY RIGHTS
IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple Powerbook
are registered trademarks of Apple Inc. Microsoft and Windows 95 &Windows 98 are registered trademarks, and Windows
and Windows for Workgroups are trademarks of the Microsoft Corporation. Toshiba is a registered trademark of Toshiba
Corporation. Kensington is a trademark of Kensington Corporation. All other products are trademarks or registered trademarks
of their respective companies. 3M is a trademark of 3M Company.

3M Austin Center
Building A145-5N-01
6801 River Place Blvd.
Austin, TX 78726-9000
3M Canada
P.O. Box 5757
London, Ontario
N6A 4T1
3M Mexico, S.A. de C.V.
Apartado Postal 14-139
Mexico, D.F. 07000
Mexico
3M Europe
Boulevard de l’Oise
95006 Cerge Pontoise Cedex
France Please recycle.
Printed in China.
© 3M 2008. All Rights Reserved.
78-6971-1429-2 Rev. A
QR77311