3One data IES618-P User manual

- 1 -
IES618 Series
Industrial Ethernet Switch
User manual
Shenzhen 3onedata Technology Co., Ltd.
Tel: [phone] Fax: [phone]
www.3onedata.com
【Summarize】
IES618 series is an industrial grade, managed and redundancy
Ethernet switch. The IES618 industrial Ethernet switches consists
of 8 Ethernet ports. The IES618-2F consists of 6 Ethernet ports
and 2 Fiber ports. The IES618-3F consists of 5 Ethernet ports and
3 Fiber ports. The IES618-4F consists of 4 Ethernet ports and 4
Fiber ports that provide an economical solution for your industrial
Ethernet connection. SW-RingTM is designed as rapid redundancy
network arithmetic. It provided recover technology for fault of
rapid redundant network, the recovery time<20ms. The switch
support AC power input series and DC power input series
optional.
The switch accorded to CE, FCC standard and Industry grade 4
design requirement, support DC redundancy power or AC single
power input and 1 channel relay alarm output, and -40～75℃
working temperature, can meet all kinds of Industrial environment
requirement. It can use in power, water conservancy,
transportation area etc.
【Packing list】
The industrial Ethernet switch is shipped with the following items.
If any of these items are missing or damaged, please contact your
customer service representative for assistance.
Industrial Ethernet switch ⅹ1
Documentation and software CD ⅹ1
User manual ⅹ1
DIN-Rail mounting kit ⅹ1
Warranty card ⅹ1
【Feature】
High performance network exchange technology
Support IEEE802.3, IEEE802.3u, IEEE 802.3x,
IEEE802.1Q, IEEE802.1p, IEEE802.1D, IEEE802.1W
SW-Ring ring network patent technology (Fault recovery
time<20ms）
Support RSTP, way exchange time<50ms
Support WEB, Telnet, CLI configuration
Support Port based VLAN and IEEE 802.1Q VLAN
Store and Forward switching process type
Support port status display, data update.
Support SNMP, IGMP Snooping
Support 8K MAC address
Support 2.0Gbps backboard bandwidth
DC power input series support redundancy power
supply(12～48VDC)
AC power input series support AC power supply(100～
240VAC/DC)
Support 1 channel relay alarm output
Reliable Industrial grade design
Industrial grade 4 design, -40-75℃work temperature
No fan deign
IP40 protection grade
DIN rail mount
【Panel layout】
Vertical view and bottom view Rear view

- 2 -
Front panel view
IES618 IES618-2F
IES618-3F IES618-4F
1. DIP switches for default factory
2. Console port
3. 2-pin terminal block for relay output
4. Ground screw
5. Power input terminal block
6. Screw holes for Wall Mounting Kit
7. DIN-Rail mounting kit
8. Relay alarm LED
9. Power indicator (PWR1, PWE2)
10. System running LED
11. Link/ACT LEDs
12. 10Base-T /100Base-TX Ethernet port
13. 100Base-FX fiber port
【Power supply input】
DC Series Switch:
The switch have redundant power input, provides one terminal
block (4 bits) for PWR1 and PWR2 input. The redundant power
can be used single and used two self-governed power to supply to
the system, PWR1 and PWR2 input at the same time, when
neither of these two power fails, the other power acts as a backup,
and automatically supplies power needs, ensure running
Ethernet reassuring. Voltage input range is 12～48VDC (terminal
block defined as: V1-、V1+、V2-、V2+).
AC Series Switch:
The Industrial Ethernet switches have singe power and
redundancy power two kinds of power input. The singe power AC
series top panel provides 3 bit terminal block for
100~240VAC/DC power entered (L/+, FG, N/-)
Important notice:
1. Power ON operation: first of all, insert power cable’s terminal
block into device’s power port, then insert power supply plug into
power source
2. Power OFF operation: First off all, unpin power plug, then
strike the terminal block, please take care of operation sequence.
【Dimension】
The series of products size is the same, and the type of the
Ethernet interface is different. Unit (mm)
【DIP Switch】
Top panel provided 4 bits DIP switch to do function configure
（ON to enable effective）,1 and 4 keep for future function. 2 is
for upgrade. 3 is recovery default factory. Please power off and
power on when you change the status of DIP switch.
【Relay connection】
Relay access terminals in the top panel of the device. Between the
two terminal relay, as an open circuit state in normal non alarm
state, when there is any alarm information to the closed state. The
two terminal block connector are used to detect both power failure
and port failure. The two wires attached to the Fault contacts form
an open circuit when the device has lost power supply from one of
the DC power inputs or one of the ports is failure. (Note: The AC
power switch does not support power alarm.)

- 3 -
【Console port】
This series product provided 1pcs procedure test port based in
serial port. It adopts RJ45 interface, located in top panel, can
configure related command through RJ45 to DB9 female cable.
【Communication connector】
10/100BaseT(X) Ethernet port
The pinout define of RJ45 port display as below, connect by UTP
or STP. The connect distance is no more than 100m. 100Mbps is
used 120Ωof UTP 5, 10Mbps is used 120Ωof UTP 3, 4, 5.
RJ 45 port support automatic MDI/MDI-X operation. can connect
the PC, Server, Converter and HUB .Pin 1,2,3,6 Corresponding
connection in MDI. 1→3, 2→6, 3→1, 6→2 are used as cross
wiring in the MDI-X port of Converter and HUB.
10Base-T/100Base-TX are used in MDI/MDI-X, the define of Pin
in the table as below.
NO. MDI signal MDI-X signal
1 TX+ RX+
2 TX- RX-
3 RX+ TX+
6 RX- TX-
4, 5, 7, 8 ——
Note：“ TX±”Transmit Data± ，“ RX±”Receive Data± ，“ —” Not use.
10/100Base-T(X) MDI (straight-through cable)
10/100Base-T(X) MDI-X (Cross over cable)
MDI/MDI-X auto connection makes switch easy to use for
customers without considering the type of network cable.
100Base-FX Fiber port
100Base-FX full-duplex SM or MM port, SC/ST/FC type .The
fiber port must be used in pair, TX (transmit) port connect remote
switch’s RX(receive) port; RX(receive) port connect remote
switch’s TX(transmit) port.
The optical fiber connection supports the line to instruct enhance
the reliability of network effectively.
Suppose: If you make your own cable, we suggest labeling the
two sides of the same line with the same letter (A-to-A and B-to-B,
shown as below, or A1-to-A2 and B1-to-B2).
【LED Indicator】
LED indictor light on the front panel of product, the function of
each LED is described in the table as below.
System indication LED
LED State Description
PWR
(1~2)
ON Power is being supplied to power
input PWR
OFF Power is not being supplied to
power input PWR
Alarm
ON When the alarm is enabled, power
or the port’s link is inactive.
OFF Power and the port’s link is active,
the alarm is disabled.
Run
ON/OFF System is not running well
Blinking System is running well
Link/ACT
(1~8)
ON Port connection is active
Blinking Data transmitted
OFF Port connection is not active
【Installation】
Before installation, confirm that the work environment meet the
installation require, including the power needs and abundant
space. Whether it is close to the connection equipment and other
equipments are prepared or not.
1. Avoid in the sunshine, keep away from the heat fountainhead or
the area where in intense EMI.
2. Examine the cables and plugs that installation requirements.
3. Examine whether the cables be seemly or not (less than 100m)
according to reasonable scheme.
18

- 4 -
4. Power: DC series product support 12 ~ 48VDC power supply;
AC series product support 100 ~ 240VAC/DC power supply;
5. Environment: working temperature: -40～75℃
Storage Temperature: -40～85℃
Relative humidity 5%～95%
DIN Rail Installation
In order to use in industrial environments expediently, the product
adopt 35mm DIN-Rail installation, the installation steps as below:
1. Examine the DIN-Rail attachment
2. Examine DIN Rail whether be firm and the position is
suitability or not.
3. Insert the top of the DIN-Rail into the slot just below the
stiff metal spring.
4. The DIN-Rail attachment unit will snap into place as shown
below.
Wiring Requirements
Cable laying need to meet the following requirements,
1. It is needed to check whether the type, quantity and
specification of cable match the requirement before cable
laying;
2. It is needed to check the cable is damaged or not, factory
records and quality assurance booklet before cable laying;
3. The required cable specification, quantity, direction and
laying position need to match construction requirements, and
cable length depends on actual position;
4. All the cable cannot have break-down and terminal in the
middle;
5. Cables should be straight in the hallways and turning;
6. Cable should be straight in the groove, and cannot beyond the
groove in case of holding back the inlet and outlet holes.
Cables should be banded and fixed when they are out of the
groove;
7. User cable should be separated from the power lines. Cables,
power lines and grounding lines cannot be overlapped and
mixed when they are in the same groove road. When cable is
too long, it cannot hold down other cable, but structure in the
middle of alignment rack;
8. Pigtail cannot be tied and swerved as less as possible.
Swerving radius cannot be too small (small swerving causes
terrible loss of link). Its banding should be moderate, not too
tight, and should be separated from other cables;
9. It should have corresponding simple signal at both sides of the
cable for maintaining.
【Specification】
Technology
Standard: Support IEEE802.3, IEEE802.3u, IEEE 802.3x,
IEEE802.1Q, IEEE802.1p, IEEE802.1D/W
Protocol: ARP, ICMP, TCP, UDP, DHCP, DNS, HTTP, Telnet,
SW-Ring, RSTP, SNMP
Flow control: IEEE802.3x, back pressure control
Function
Switch function: SW-Ring, QOS, 802.1QVLAN, RSTP, SNMP,
Port trunking, static multicast filter, port mirroring,
bandwidth management, broadcast storm control, port flow
statistics, upgrade online, up and download configuration file,
user name access system
SW-Ring: Support Single, Couple, Chain, Dual homing
Exchange attribute:
100M forward speed: 148810pps
100M maximum filter speed: 148810pps
Transmit mode: store and forward
System exchange bandwidth: 2.0G
MAC address table: 2K
Memory: 1M
Interface
Electric port: 10Base-T/100Base-TX/1000Base-TX auto speed
control, Half/full duplex and MDI/MDI-X auto detect
100M optic fiber port: 100Base-FX, SC/ST/FC connector
Console port: debug serial port carry out CLI command
Alarm port: 2 bit 7.62mm terminal block,
1 channel relay alarm output
Transfer distance
Twisted cable: 100M（standard CAT5/CAT5e cable）
Multi-mode: 1310nm, 2Km
Single-mode: 1310nm, 20/40/60Km
1550nm, 80/100/120Km
LED indicator:
DC input series
Run indicator: Run
Interface indicator: Link (1~8)
Power supply indicator: P1, P2
Alarm indicator: Alarm
AC input series
Run indicator: Run
Interface indicator: Link (1~8)
Power supply indicator: PWR
Alarm indicator: Alarm
Power supply
DC input series
Input voltage: 12~48VDC
AC input series
Input voltage: 100~240VAC/DC
Type of input: 4 bit 7.62mm pitch terminal block
Consumption

- 5 -
IES618-P (12~48VDC):
Unload consumption: 1.4W@12VDC
Full load consumption: 3.5W@12VDC
IES618-P (220VAC):
Unload consumption:1.8W@220VAC
Full load consumption: 3.7W@220VAC
IES618-2F-P (12~48VDC):
Unload consumption: 3.1W@12VDC
Full load consumption: 5.7W@12VDC
IES618-2F-P (220VAC):
Unload consumption: 3.3W@220VAC
Full load consumption: 4.8W@220VAC
IES618-3F-P (12~48VDC):
Unload consumption: 3.9W@12VDC
Full load consumption: 5.5W@12VDC
IES618-3F-P (220VAC):
Unload consumption: 4.2W@220VAC
Full load consumption: 5.5W@220VAC
IES618-4F-P (12~48VDC):
Unload consumption: 4.9W@12VDC
Full load consumption: 6.4W@12VDC
IES618-4F-P (220VAC):
Unload consumption: 5.0W@220VAC
Full load consumption: 6.1W@220VAC
Working environment
Working temperature: -40～75℃
Storage temperature: -40～85℃
Relative Humidity: 5%~95% (no condensation)
Mechanical Structure
Shell: IP40 protect grade, metal shell
Installation: DIN-Rail mounting
Weight: ≤808g
Size（W×H×D）:53mm×138mm×110mm
Industry Standard
EMI: FCC Part 15, CISPR (EN55022) class A
EMS: EN61000-4-2 (ESD), Level 4
EN61000-4-3 (RS), Level 3
EN61000-4-4 (EFT), Level 4
EN61000-4-5 (Surge), Level 4
EN61000-4-6 (CS), Level 3
EN61000-4-8, Level 5
Shock: IEC 60068-2-27
Free fall: IEC 60068-2-32
Vibration: IEC 60068-2-6
Certification
CE, FCC, RoHS, UL508 (Pending)
Warranty: 5 years