3One data IES6312 Series User manual

IES6312 Series
Managed Industrial PoE/non-PoE
Ethernet Switch Quick Installation
Guide
3onedata Co., Ltd.
【
Package Checklist
】
Please check whether the package and accessories are intact
while using the switch for the first time. The following list is the
standard configuration; please follow up the real product.
1.
Industrial Ethernet switch
2.
CD
3.
Quick installation guide
4.
Warranty card
5.
Certification
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【
Product Overview】
The series are managed DIN-Rail industrial PoE/non-PoE
Ethernet switches. Module as follows:
Model I IES6312-8GP4GF-2P24-120W(8 Gigabit PoE ports
+ 4 Gigabit fiber ports, 24VDC PoE, PoE power of
120W)
Model II IES6312-8GP4GS-2P24-120W(8 Gigabit PoE ports
+ 4 Gigabit SFP slots, 24VDC PoE, PoE power of
120W)
Model III IES6312-8GP4GF-2P48-120W(8 Gigabit PoE ports
+ 4 Gigabit fiber ports, 48VDC PoE, PoE power of
120W)
Model IVIES6312-8GP4GS-2P48-120W(8 Gigabit PoE ports
+4 Gigabit SFP slots, 48VDC PoE, PoE power of
120W)
Model V IES6312-8GP4GF-2P48-240W(8 Gigabit PoE ports
+ 4 Gigabit fiber ports, 48VDC PoE, PoE power of
240W)
Model VIIES6312-8GP4GS-2P48-240W(8 Gigabit PoE ports
+ 4 Gigabit SFP slots, 48VDC PoE, PoE power of
240W)
Model VII IES6312-8GT4GF-2P48(8 Gigabit copper ports + 4
Gigabit fiber ports,12~48VDC)
Model VIII IES6312-8GT4GS-2P48(8 Gigabit copper ports + 4
Gigabit SFP slots, 12~48VDC)
Model IXIES6312-8GT4GF-P220(8 Gigabit copper ports + 4
Gigabit fiber ports, 100~240VAC)
Model X IES6312-8GT4GS-P220(8 Gigabit copper ports + 4
Gigabit SFP slots, 100~240VAC)
【
Panel Design
】
Top view, Bottom view and Rear view
Front view
Model I, III, V Model VII Model IX
Model II, IV, VI Model VIII Model X
1. Power input terminal block
2. Relay alarm output terminal block
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili,
Nanshan District,
Shenzhen
Website:
www.3onedata.com
Te l :
[phone]
Fax:
[phone]

3. DIP switch
4. Console port
5. Grounding screw
6. Wall mounting screw hole
7. DIN-Rail mounting kit
8. Power supply indicator P1/P2/PWR
9. Relay alarm indicator ALM
10. Device running indicator RUN
11. PoE indicator PoE+
12. Interface connection indicator Link
13. Gigabit PoE port
14. Gigabit fiber port
15. Gigabit copper port
16. Gigabit SFP slot
【
Mounting Dimension
】
Unit: mm
Notice:
The hanging panel accessories on the right side of the
picture above need additional purchase.
Attention before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【
DIN-Rail Mounting
】
For convenient usage in industrial environments, the product
adopts 35mm DIN-Rail mounting, mounting steps as below:
Check if the DIN-Rail mounting kit is installed firmly.Step 1
Insert the bottom of DIN-Rail mounting kit (one sideStep 2
with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Check and confirm the product is firmly installed onStep 3
DIN-Rail, then mounting ends.
【Disassembling DIN-Rail】
Device power off.Step 1
After lift the device upward slightly, first shift out theStep 2
top of DIN-Rail mounting kit, then shift out the
bottom of DIN-Rail, disassembling ends.
Attention before power on:
Power ON operation: first connect power line to the
connection terminal of device power supply, then
power on.
Power OFF operation: first unpin the power plug,
then remove the power line, please note the
operation order above.
【Power Supply Connection】
DC power supply
The series provide 6-pin 5.08mm pitch
terminal blocks, and two independent
DC power supply systems of PWR1
and PWR2. PIN1-PIN4 are used for
power supply input. This series provide
8 types of product and adopt 4 different
power supply ranges. Please be aware of the corresponding
power supply type of the device lest damaging the device.
24VDC PoE device
The power supply of 24VDC PoE device model I and model II
has built-in 12A over-current protection, and support
anti-reverse connection and redundant backup. Input power is
24VDC.
48VDC PoE device
The power supply of 48VDC PoE device model III, model IV,
model V and model VI has built-in 5A over-current protection,
and support anti-reverse connection and redundant backup.
Input power is 48VDC.
12~48VDC non-PoE device
The power supply of 12~48VDC non-PoE device model VII
and model VIII has built-in 3A over-current protection, and
support non-polarity and redundant backup. Input power
range is 12~48VDC.
AC power supply
This series provide 6 pins 5.08mm
pitch terminal blocks and AC power
supply system.
220VAC non-PoE device
The power supply of 220VAC
non-PoE device model IX and model X has built-in 5A
over-current protection. Input power range is 100~240VAC.
【Relay Connection】
This series of products provide 6-pin
5.08mm pitch terminal blocks. Relay
terminals are a pair of normally open
contacts in device alarm relay. They
are open circuit in normal non alarm
state, closed when any alarm

information occurs. Such as: it's closed when power off, and
send out alarm. This series switches support 1 channel relay
alarm information output, support DC power alarm information
or network abnormal alarm output, it can be connected to
alerting lamp, alarm buzzer, or other switching value collecting
devices to warn operators timely when alarm information
occurs.
【
DIP Switch Setting
】
Provide 4-bits DIP switch for function setting, where
"ON" is enable valid terminal. DIP switch define as
follows:
DIP
Definition
Operation
1 Restore
factory setting
When it is set to ON, the device
will reboot and restore to factory
setting automatically. Then pull
it back.
2
Reserved
-
3
Reserved
-
4
Reserved
-
【
Console Port Connection
】
The device provides 1 program debugging port
based on RS232 serial port. The interface
adopts RJ45 port, and can conduct device CLI
command line management after connecting to PC.
PIN
2
3
5
Definition
TXD
RXD
GND
【
Checking LED Indicator
】
This device provides LED indicators to monitor device’s
operating state, which has simplified the troubleshooting
process comprehensively. The status of each LED is
described in the table below:
LED
Status
Description
RUN
ON The device is powered on or the
device is abnormal.
OFF The device is powered off or the
device is abnormal.
Blinking
Blink 1 time/s, the device runs
normally
ALM
ON DC
Power supply, port failure
alarm
OFF Relay alarm is turned off or has
no alarm
P1/P2/PWR
ON Power supply P1/P2/PWR is
connected and running normally
OFF
Power supply P1/P2/PWR is
disconnected and running
abnormally
Link
G1-G12
ON
Ethernet port has established
valid network connection
Blinking
Ethernet port is in active status
OFF Ethernet port has not established
valid network connection
POE G1-G8
ON PD device is powered over PoE
port normally
OFF
PD device is not powered over
PoE or not connected to PoE
【
Logging in to WEB Interface
】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device’s configuration interface via IE
browser is shown as below:
Configure the IP addresses of computer and theStep 3
device to the same network segment, and the
network between them can be mutually accessed.
Enter device’s IP address in the address bar of theStep 4
computer browser.
Enter device’s username and password in the loginStep 5
window as shown below.
Click “OK” button to login to the WEB interface ofStep 6
the device.
Note:
The default IP address of the device is “192.168.1.254”.
The default username and password of the device is
“admin”.
If the username or password is lost, user can restore it to
factory settings via device DIP switch or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
Gigabit PoE port 10/100/1000Base-T(X), RJ45,
automatic flow rate control,
full/half duplex mode,
MDI/MDI-X autotunning; PoE
power supply pins: V+, V+, V-,
V-. Output power is 30W

Gigabit copper port 10/100/1000Base-T(X), RJ45,
automatic flow rate control,
full/half duplex mode,
MDI/MDI-X autotunning
Gigabit fiber port 1000Base-FX
, optional
SC/ST/FC interface
Gigabit SFP slot
1000Base-SFP, LC
Console port CLI commend line
management port(RS-232),
RJ45
Alarm port 6-pin 5.08mm
pitch terminal
blocks (relay occupies 2 pins),
support 1 relay alarm output,
current
load capacity is
1A@30VDC or
0.3A@125VAC
Indicator
Power indicator, run indicator,
interface connection indicator,
alarm indicator and PoE
indicator
Switch property
Backplane bandwidth
24G
Buffer size
4Mbit
MAC address table 8K
Power supply
Model I, Model II 24VDC PoE, anti-reverse
connection, redundant
backup, built-
in 12A
over-current protection
Model III, Model IV,
Model V, Model VI
48VDC PoE, anti-reverse
connection, redundant
backup, built-
in 5A
over-current protection
Model VII, Model VIII 12~48VDC, non-polarity,
redundant backup, built-in 3A
over-current protection
Model IX, Model X100~240VAC, built-
in 5A
over-current protection
Terminal block 6-pin 5.08mm
pitch terminal
blocks, power supply occupies
4 pins
Power consumption
Model I No-load: 9.1W@24VDC
Full-load: 141.5W@24VDC
Model II No-load: 6.0W@24VDC
Full-load: 100.8W@24VDC
Model III No-load: 8.8W@48VDC
Full-load: 130.0W@48VDC
Model IV, No-load: 5.2W@48VDC
Full-load: 132.9W@48VDC
Model V No-load: 8.8W@48VDC
Full-load: 199.6W@48VDC
Model VI No-load: 5.2W@48VDC
Full-load: 200.2W@48VDC
Model VII No-load: 7.5W@24VDC
Full-load: 10.5W@24VDC
Model VIIII No-load: 4.2W@24VDC
Full-load: 10.2W@24VDC
Model IX No-load: 7.7W@220VAC
Full-load: 11.1W@220VAC
Model X No-load: 4.6W@220VAC
Full-load: 10.4W@220VAC
Operating environment
Operating temperature
-40
～
75
℃
Storage temperature
-40
～
85
℃
Operating humidity
5%
～
95% (no condensation)
Protection grade
IP40 (metal shell)