Aaeon AEC-VS01 User manual

Embedded Controller AEC-VS01
AEC-VS01
Embedded Controller
4-Channel PoE for Surveillance
Intel
®Atom™ D2550 1.86GHz Processor
Dual LAN, 4 USB2.0, 4 COM, 1 VGA
8 DIO, 1 Mini Card
AEC-VS01 Manual 2nd Ed.
January 8th, 2014

Embedded Controller
A E C - V S 0 1
i
TCopyright Notice
This document is copyrighted, 2013. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in
this manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, or for
any infringements upon the rights of third parties that may result
from its use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, AAEON assumes no liabilities resulting from errors or
omissions in this document, or from the use of the information
contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.

Embedded Controller
A E C - V S 0 1
ii
Acknowledgments
All other products’name or trademarks are properties of their
respective owners.
AMI is a trademark of American Megatrends, Inc.
CompactFlashP
™
Pis a trademark of the Compact Flash
Association.
Microsoft WindowsP
®
Pis a registered trademark of Microsoft
Corp.
Intel®, Atom™are trademarks of Intel Corporation.
PC/AT, PS/2, and VGA are trademarks of International
Business Machines Corporation.
All other product names or trademarks are properties of their
respective owners.

Embedded Controller
A E C - V S 0 1
iii
Packing List
Before you begin operating your PC, please make sure that the
following materials are enclosed:
1 AEC-VS01 Embedded Controller
2 Wallmount Brackets
1 Screw Package
1 CD-ROM for manual (in PDF format) and drivers
1 Phoenix Power Connector
If any of these items should be missing or damaged, please contact
your distributor or sales representative immediately.

Embedded Controller
A E C - V S 0 1
iv
Safety & Warranty
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Do
not use liquid or spray detergents for cleaning. Use a damp cloth.
4. For pluggable equipment, the power outlet must be installed near
the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a firm surface during installation. Dropping
it or letting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient over-voltage.
12. Never pour any liquid into an opening. This could cause fire or
electrical shock.
13. Never open the equipment. For safety reasons, only qualified
service personnel should open the equipment.
14. If any of the following situations arises, get the equipment
checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.

Embedded Controller
A E C - V S 0 1
v
d. The equipment does not work well, or you cannot get it
to work according to the user’s manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT
WHERE THE STORAGE TEMPERATURE IS BELOW -20°C
(-4°F) OR ABOVE 70°C (158°F). IT MAY DAMAGE THE
EQUIPMENT.
FCC
This device complies with Part 15 FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received including
interference that may cause undesired
operation.
Caution:
There is a danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instructions and your local government’s recycling or
disposal directives.

Embedded Controller
A E C - V S 0 1
vi
Below Table for China RoHS Requirements
产品中有毒有害物质或元素名称及含量
AAEON Boxer/ Industrial System
部件名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印刷电路板
及其电子组件
×
○
○
○
○
○
外部信号
连接器及线材
×
○
○
○
○
○
外壳
×
○
○
○
○
○
中央处理器
与内存
×
○
○
○
○
○
硬盘
×
○
○
○
○
○
电源
×
○
○
○
○
○
O：表示该有毒有害物质在该部件所有均质材料中的含量均在
SJ/T 11363-2006 标准规定的限量要求以下。
X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
SJ/T 11363-2006 标准规定的限量要求。
备注：
一、此产品所标示之环保使用期限，系指在一般正常使用状况下。
二、上述部件物质中央处理器、内存、硬盘、电源为选购品。

Embedded Controller
A E C - V S 0 1
vii
CC
Chapter 1 General Information
1.1 Introduction................................................................ 1-2
1.2 Features .................................................................... 1-3
1.3 Specifications ............................................................ 1-4
Chapter 2 Hardware Installation
2.1 Dimension and I/O of AEC-VS01..............................2-2
2.2 Location of Connectors and Jumpers of The Main Board
......................................................................................... 2-4
2.3 List of Jumpers..........................................................2-6
2.4 List of Connectors .....................................................2-7
2.5 DIO Pin Definition...................................................... 2-9
2.6 PoE1~4 Port Pin Definition (MID-SPAN) ..................2-9
2.7 Hard Disk Drive Installation....................................... 2-10
2.8 RAM Installation........................................................ 2-13
2.9 CFast Card Installation.............................................. 2-15
2.10 Wallmount Installation ...........................................2-16
Chapter 3 AMI BIOS Setup
3.1 System Test and Initialization. ..................................3-2
3.2 AMI BIOS Setup........................................................ 3-3
Chapter 4 Driver Installation
4.1 Installation .................................................................4-3
Appendix A Programming The Watchdog Timer
A.1 Programming ........................................................A-2

Embedded Controller
A E C - V S 0 1
viii
A.2 ITE8783 Watchdog Timer Initial Program ............A-6
Appendix B I/O Information
B.1 I/O Address Map ..................................................B-2
B.2 1st MB Memory Address Map ...............................B-4
B.3 IRQ Mapping Chart ..............................................B-5
B.4 DMA Channel Assignments .................................B-6
Appendix C Digital I/O
C.1 Digital I/O.............................................................. C-2
Appendix D AHCI Setting
D.1 Setting AHCI......................................................... D-2

Embedded Controller
A E C - V S 0 1
Chapter 1 General Information 1- 1
General
Information
Chapter
1

Embedded Controller
A E C - V S 0 1
Chapter 1 General Information 1- 2
1.1 Introduction
AAEON introduces the newest product in for entry level fanless
boxer, AEC-VS01, which utilizes the Intel® Atom™ D2550
processor and 4-channel PoE ports for video surveillance
applications. With compact, and aluminum case easily for
customers install in the customer's own housing, or as a
stand-alone application where space is limited and the environment
harsh.
With PoE(Power Over Ethernet ) function, customer can easy install
their IP Camera anywhere which cable install limitation issue and
extra cost for system maintenance.
Also test by 3rd party surveillance software, customers can remote
management and maintenance their system.
The AEC-VS01 supports a rich I/O capability, including four serial
ports, four USB 2.0 ports, digital I/Os, expand storage, and 4
channel PoE ports, which make AEC-VS01 ideal to integrate,
deploy, and manage for system development, and further
accelerate time to video surveillance market.
In this era of information explosion, the advertising of consumer
products will not be confined to the family television, but will also
spread to high-traffic public areas, like department stores, the bus,
transportation station, the supermarket etc. The advertising

Embedded Controller
A E C - V S 0 1
Chapter 1 General Information 1- 3
marketing industry will resort to every conceivable mean to transmit
product information to consumers. System integrators will need a
multifunction device to satisfy commercial needs for such public
advertising.
The AEC-VS01 is a standalone high performance controller
designed for long-life operation and with high reliability. It can
replace traditional methods and become the mainstream controller
for the multimedia entertainment market.
1.2 Features
Intel®AtomTM D2550 1.86 GHz Processor
Intel®NM10 Express chipset
USB2.0 x 4
COM x 4
Dual Gigabit Ethernet LAN
DIO x 8
USB type 4-CH PoE
Power input: 24~30V
VGA Output
Fanless System Design

Embedded Controller
A E C - V S 0 1
Chapter 1 General Information 1- 4
1.3 Specifications
System
CPU
Intel®AtomTM D2550 1.86 GHz
Processor
Memory
DDR3 800/1066 SODIMM x 1, Max.
4GB)
VGA
VGA x 1
Ethernet
Gigabit Ethernet, RJ-45 connector x 2
Hard Disk Storage
2.5”SATA HDD Bay x 1
Expansion
Mini Card Slot x 1
DIO x 8
4-Channel PoE
LCD/CRT
Controller
Integrated in Processor, shared
system memory by Intel®DVMT
Technology
Solid Storage
Disk
CFastTM slot x 1 (w/ cover protection)
Serial Port
RS-232/422/485 x 1, RS-232 x 3
(optional x 2)
USB
USB 2.0 x 4
System Control
Power ON/OFF
LED Indicator
Power LED x 1, Hard disk active LED
x 1, CFast™slot x 1, Antenna hole x 2
Power Supply
DC power input 12V/ DC 24-30V w/
3-pin terminal block
OS Support
Windows® 7, Linux Fedora Core,
Windows® XP
Mechanical and Environmental
Construction
Aluminum Alloy Chassis

Embedded Controller
A E C - V S 0 1
Chapter 1 General Information 1- 5
Color
Dark Gray
Mounting
Wallmount
Dimension
7.76”(W) x 4.02”(H) x 4.80”(D)
(197 mm x 102 mm x 122 mm)
Gross Weight
9.9 lb (4.5 kg)
Net Weight
7.26 lb (3.3 kg)
Operating
Temperature
32°F ~ 113°F (0°C ~ 45°C)
Storage
Temperature
32°F ~ 158°F (0°C ~ 70°C)
Storage Humidity
5 ~ 95% @ 40°C, non-condensing
Vibration
1 g rms/ 5~500Hz/ random
operation –HDD
Shock
20 G peak acceleration (11msec.
duration) –HDD
EMC
CE/FCC Class A

Embedded Controller
A E C - V S 0 1
Chapter 2 Hardware Installation 2-1
Hardware
Installation
Chapter
2

Embedded Controller
A E C - V S 0 1
Chapter 2 Hardware Installation 2 - 2
2.1 Dimension and I/O of AEC-VS01
DC 24-30V
CFast

Embedded Controller
A E C - V S 0 1
Chapter 2 Hardware Installation
2 - 3
Front View
DC 24-30V
CFast
Rear View

Embedded Controller
A E C - V S 0 1
Chapter 2 Hardware Installation 2 - 4
2.2 Connectors and Jumpers of The Main Board
Component Side
Component Side Solder Side

Embedded Controller
A E C - V S 0 1
Chapter 2 Hardware Installation
2 - 5
Solder Side
Component Side Solder Side

Embedded Controller
A E C - V S 0 1
Chapter 2 Hardware Installation 2 - 6
2.3 List of Jumpers
The board has a number of jumpers that allow you to configure your
system to suit your application.
The table below shows the function of each of the board's jumpers:
Label
Function
JP1
Auto Power Button Selection
JP2
Clear CMOS
JP3
COM2 RI/+5/+12V Selection
JP4
Touch Screen 4/5/8-wires Mode Selection
JP5
Brightness Control for 2nd LVDS
JP6
2nd LVDS Backlight Bias/PWM Mode Selection
JP7
2nd LVDS Operating Voltage Selection
JP8
2nd LVDS Inverter Voltage Selection
JP9
1st LVDS Inverter Voltage Selection
JP10
1st LVDS Backlight Bias/PWM Mode Selection
JP11
1st LVDS Operating Voltage Selection