AAON PT-Link II LON-3 Assembly instructions

ASM01883
PT-Link II LON-3®
Installation Sheet
PT-Link II LON-3®Overview
The PT-Link II LON-3®, provides bi-directional communication between
ONE* of the following types of Orion controllers—VCCX2, VCC-X,
VCB-X, VCM-X, SA, VCM, MUA II, or VAV/CAV:
VCCX2 Controller (SS1088)
VCC-X Controller (SS1079)
VCB-X Controller (SS1051)
VCM-X Controller (SS1026, SS1030, SS1032, SS1033,
SS1034, Y200920)
SA Controller (Y200921)
VCM Controller (SS1016, Y200409, Y200616, Y200822)
VAV/CAV Controller (SS1003, Y200301) and
MUA II Controller (SS1004, Y200405)
To determine what controller you have, you must look at the software
label located on the controller. NOTE: The label is located on the
EPROM on older devices. If the controller label does not match any of
the SS or Y numbers listed above, your controller will not work with
the PT-Link II LON®.
*NOTE: The PT-Link II LON®device can be used to connect to
only one Orion controller. If more than one Orion control-
ler is present in a system, each one will require a PT-Link
II LON®device for integration with a LON®protocol
network.
Data Sharing and Scheduling
• Provides values from points on the Orion side of the
gateway to LON®devices as if the values were
originating from LON®objects.
• Allows LON®devices to modify point values on the
Orion controller side of the PT-Link II LON®by using
standard LON®write services.
Includes: PT-Link II LON-3®Controller, 10 Foot CAT5e Crossover Cable,
(3) Self-drilling 8 x 1” Hex Head Screws, PT-Link II Flash Drive
Technical Data
LON®Loop TP/FT-10 (78 Kps)
Orion Controller Loop RS-485, 9600 Baud Rate
Network Protocol LONWorks®
Orion Controls Protocol
Communications
HSI Open Protocol Token Passing
Power Input Voltage 18-30 VAC
Power Consumption 10 VA Maximum
Operating Temp -30°F to 150°F
Operating Humidity 0-95% RH Non-Condensing
Weight 4.7 oz.
Table 1: PT-Link II LON-3®Technical Data
System Requirements
• Computer running Microsoft®Windows®10
operating system.
• Ethernet Crossover Cable (supplied).
• PT-Link LON®and RUINET software—
 includedonashdriveandalsodownloadable
from www.aaon.com/controlstechsupport
• Prism 2 software—downloadable from
www.aaon.com/prism
Hardware Specications
The PT-Link II LON-3 Technical Guide
is located on the included ash drive
and can also be downloaded from www.
aaon.com/PTLink

The following steps are a quick means to get the PT-Link II LON-3®
operational for many simple installations. This quick start depends on
the ability of the front end to accurately and successfully obtain the
required information directly over the LON®connection. If the front
end cannot successfully do this, it will be necessary to manually obtain
anXIFlefromthePT-Linkasdescribedonpage 7 in the PT-Link
II LON-3 Technical Guide and then to manually commission the PT-
Link II LON-3®device.
1. Familiarize yourself with the PT-Link II components
(Figure 1). NOTE: The DIP Switches should be left in their
default positon which is all OFF. They are not used in this
application.
2. Connect your PT-Link II LON-3®to the Unit Controller on
your system (only one) and connect your PT-Link II to the
LON Network (Figure 2, page 3).
3. Power up the PT-Link II LON-3®with an appropriately sized
isolated 24 VAC power. (Note that the Unit Controller
should already be powered up and running). Do not use the
same power for both the PT-Link and the Unit Controller,
improper wiring of these two devices on the same power
source will cause damage to both the PT-Link and the
Unit Controller as they do not have isolated communications.
4. Allow at least 3 minutes for the PT-Link II LON-3®to learn
internally all its information and prepare the data tables; after
this point, use the learning capabilities of your front end to
discover the PT-Link device on the LON network and
subsequently to discover the points provided by the PT-Link
gateway.
Quick Start Guide
Figure 1: PT-Link II LON-3®Dimensions and Components

Connections and Wiring
Figure 2: PT-Link II LON-3®Interface Wiring to Unit Controller (VCCX2 Shown)

LON®and LONWorks®are registered trademarks of EschelonCorporation.
FieldServer is a registered trademark of FieldServer Technologies, Milpetas, CA
Windows®is a registered trademark of Microsoft Corporation.
8500 NW River Park Drive • Parkville, MO • 64152
Ph: [phone] • Fax: [phone]
ASM01883-INSTL-01A
Printed in the USA • © April 2020 AAON • All Rights Reserved
AAON Factory Technical Support: 918-382-6450
techsuppor[email protected]
AAON Controls Support: 866-918-1100
Monday through Friday, 7:00 AM to 5:00 PM
central standard time
www.aaon.com/controlstechsupport
NOTE: Before calling Technical Support, please have the
model and serial number of the unit available.
PARTS: For replacement parts please contact your local
AAON Representative.