Aastra 9120 User manual

9120 USER GUIDE

i
Table of Contents
Table of Contents
Introduction.................................................................................................. 1
Emergency service Feature........................................................................ 1
Unpacking your phone ................................................................................1
Key Descriptions ......................................................................................... 2
Basic Installation.......................................................................................... 4
Pre-installation information for the 9120 telephone..................................... 4
Special information...................................................................................... 5
Making and Answering Calls ...................................................................... 8
Making a call............................................................................................... 8
Answering a Call .........................................................................................8
Using the Hold Key...................................................................................... 8
Switching between two lines ...................................................................... 9
Using the Conference key...........................................................................9
Extension in Use......................................................................................... 9
Making a Handsfree call.............................................................................. 9
Muting a Handsfree call ............................................................................10
Using the Redial List................................................................................. 10
Call Waiting ID........................................................................................... 11
Turning the display of Call Waiting ID on or off.......................................... 12
Changing the display language................................................................. 12
Setting the date and time..........................................................................13
Turning the ringer on and off..................................................................... 13
Setting the ring tone and ringer volume.................................................... 13
Changing the Prime Line........................................................................... 14
Clear Message Lamp................................................................................ 14
Directory ..................................................................................................... 15
Directory names........................................................................................ 15
Saving numbers and names to the Directory............................................ 15
Saving an active call into the Directory .....................................................16
Saving a memory key entry to the Directory............................................. 16
Entering Names ........................................................................................ 16
Making a call from the Directory................................................................ 16
Finding items in the Directory.................................................................... 17
Editing in the Directory.............................................................................. 17
Deleting items from the Directory.............................................................. 17
Callers List.................................................................................................. 18
Using the Callers List................................................................................ 18
Setting up the Callers List......................................................................... 18
Finding an item in the Callers List............................................................. 19
Making a call from the Callers List............................................................ 19
Editing in the Callers List........................................................................... 19
Saving Callers List numbers to the Directory or a Memory key................ 20
Deleting from the Callers List.................................................................... 20
Memory keys .............................................................................................. 21
Saving numbers and names into memory keys ........................................21
Saving from the display into memory keys................................................21
Saving an active call into a memory key................................................... 22

ii
Table of Contents
Table of Contents
Saving numbers and names into shift memory keys.................................22
Labeling the memory keys ........................................................................22
Making calls from memory keys ...............................................................23
Editing memory keys.................................................................................23
Deleting memory keys...............................................................................23
Saving features in memory keys ...............................................................23
Using feature keys.....................................................................................24
Saving a feature and light in memory keys................................................24
Using Feature Light keys...........................................................................25
Advanced Options......................................................................................26
Turning the Call timer on or off..................................................................26
Selecting the dial pad mode......................................................................26
Entering area codes..................................................................................26
The Secure Numbers Feature...................................................................27
Using a headset with your telephone........................................................28
Extension in use........................................................................................28
Display Icons and Messages.....................................................................29
The Callers List screen..............................................................................29
Knowing when you have a message.........................................................29
Icon in the Callers List...............................................................................29
General display messages........................................................................30
Callers List display messages...................................................................31
Learning about the lights...........................................................................31
Set indicator light messages .....................................................................32
Line and Handsfree indicator light messages ...........................................32
Viewing multiple display and light messages ............................................32
Troubleshooting .........................................................................................33

1
Introduction
Introduction
Congratulations.... . on the purchase of your 9120 telephone.
This guide contains information on the 9120.
Emergency Service Feature
The Model 9120 will provide basic telephone service during a power failure. How-
ever, only the dial pad and handset will function. If on a handset call when a power
failure occurs, the Model 9120 will keep the call. Handsfree calls will not be re-estab-
lished during a power interruption.
Unpacking your phone
Along with this user guide the following items are included with your telephone.
The 9120 is an advanced two-line telephone, that offers the following features:
• Handsfree (speakerphone) with mute capa-
bilities
• Headset compatible
• 100 name and number Callers List
• Personal Directory for 100 name and num-
ber directory
• 14 speed dial positions for frequently called
numbers or feature access codes
• Last number redial
Telephone Memory key card
and plastic lens
Handset
Telephone line cord
Handset cord
Telephone stand Regulatory sheetPower adaptor
Number card
and plastic lens
The power adaptor is 16 VAC, 250mA - please see the regulatory sheet for safety instructions
regarding the power adaptor and operation of the telephone.

2
Introduction
Key Descriptions
Keys Key Description
Set Indicator
Light
Flashes when the telephone rings, or when a call is on hold; lights up
when a message is waiting or when a feature or extension is in use. See
Set indicator light messages on page 31 for more information.
14 Programma-
ble Keys
Stores a name and number or feature for easy access.
Internal Head-
set Jack
Allows you to plug a headset with a standard 2.5mm jack. See Using a
headset with your telephone
on page 28.
Options
Save
Delete
Directory
Shift
Callers
Flash
Redial
Dial
Conference
Line 2
Line 1
Mute
Callers
Set Indicator Light
Options Key
Backlit Display
Navigational Keys
Handset
Volume Bar
Dial Pad
Line1 & Line2 Keys
14 Memory Keys
Headset Jack

3
Introduction
I
Access a list of 11 basic options to customize the features of your tele-
phone.
J
Stores up to 100 names and phone numbers (stored in alphabetical
order). See
Directory on page 15 for more information.
K
Use to store numbers and names in Directory, in memory keys and to
save Option feature settings.
L
Removes individual entries in the Directory, or Callers List. Erases
memory key information.
H
Use to access the seven two-touch memory positions.
SVW
allows you to move up or down in the Directory, Callers List,
Options List and the Redial List. When you are editing entries on the
display, T
allows you to backspace and erase characters and U allows
you to view multiple messages on the telephone display or adds a space
between characters.
N
Ends an active call. Goodbye exits an open list, such as the Directory
Options or Callers List. It will not hang up a call that is on hold.
O
Places calls on or off hold. See Using the Hold Key on page 8 for more
information.
R
Sets the ringer volume when the telephone is idle; sets the handset and
speaker volume while on call. See
Setting the ring tone and ringer vol-
ume
on page 13 for more information.
P Activates the speaker and microphone so you can listen and talk without
using the handset; also mutes the microphone so that your caller cannot hear
you (the light indicator will ßash when the microphone is muted) .
G
F
Select either line key to answer ringing calls (line indicator light will
ßash for ringing calls). Press either line key to place outgoing calls.
E
Joins the calls on the two lines together. See Using the Conference key on
page 9 for more information.
A
Access a list of the last 100 calls received. The list begins with the new-
est call and ends with the oldest. The oldest call is automically deleted
to make room for the new calls when the list becomes full. See
Callers
List
on page 18 for more information
B
Use with the network features such as Call Waiting and Three Way Call-
ing (ßash is also referred to as link).
C
Displays the last ten phone numbers dialed out on the telephone. See
Using the Redial List on page 10 for more information.
D
Dials the displayed telephone number, automatically activates the
handsfree mode if the handset is not picked up.
Y
To indicate G or F in this user guide.
M
Memory keys store numbers, names and features. See Memory keys on
page 21.
Keys Key Description

4
Basic Installation
Basic Installation
Pre-installation information for the 9120 telephone
The 9120 telephone is a two-line telephone. Before you begin installing it, you need to
know how the telephone lines are connected to the phone jacks at your home or ofÞce.
When two telephone lines are installed on the same phone jack, one tele-
phone cord is required to connect both lines to your 9120 telephone.
When two telephone lines are installed on separate phone jacks, two tele-
phone cords are required to connect both lines to your 9120 telephone. A
second telephone cord will be required to connect both lines to your 9120
telephone.
If you want to combine two telephone lines onto one phone jack, contact
your telephone company.
1. Connect the Handset 2.Connect the Cords
Attach one end of the coiled handset cord
to the handset and the other end to the
handset port
jon the back of the tele-
phone.
Route the handset cord along the groove
leading off the side of the telephone as
shown in the illustration.
Plug one end of the telephone cord into
1 lon the back of the telephone and the
other end to the phone jack.
Connect the small end of the power
adaptor to the kport on the back of the
telephone, and plug the other end into
an electrical outlet.
3. Attach the Stand for Desk Mount
If you plan to mount the telephone on the wall, you do not need to attach the stand.
Lower the stand as shown below into
the slots on the back of the telephone.
Slide the stand in the direction shown
below until it clicks into the locked position.
1

5
Basic Installation
Special information
You must conÞrm if the two telephone lines are installed on the same phone jack, or on
two separate phone jacks.
Read your 9120 telephone display. If it prompts you to select a language, follow the
directions on the telephone display to choose your language of choice.
When both lines are installed on the same phone jack, the
telephone display shows the time and date.
When only one line is installed on a phone jack, the tele-
phone display shows a Check line cord message.
4. Connect the second telephone cord 5. Connect optional equipment to the telephone
You must use the second telephone cord
that was provided with your 9120 tele-
phone to complete installation step 4.
Plug one end of the telephone cord into
2 lon the back of the telephone and
the other end to the phone jack.
Both telephone lines on the 9120 telephone
must be connected to 1 lon the back of
the telephone to connect a fax or modem
peripheral. Plug one end of the telephone
cord into 2 lon the back of the telephone
and the other end to a fax machine or
modem.


Jan 1 12:00 PM


Jan 1 12:00 PM
Check line cord
Line 2
22

6
Basic Installation
6. Attach the cords to the telephone stand 7. Mount the telephone on the wall
Route the cords along the groove on the
telephone stand as shown in the illustra-
tion.
It is recommended that you use a wall-
mounting plate which is available
through your telephone company or a
local retailer. You will Þnd it easier to
wall-mount the telephone if you pur-
chase one or two short 20 cm (8”) tele-
phone cords and use them in place of the
long telephone cord(s).
Coil the telephone cord(s) into the space
provided on the back of the telephone.
Line up the keys on the wall mounting
plate with the key holes on the back of
the telephone. Place the telephone onto
the wall mounting plate, and then push
down to secure the telephone into place.
8. Insert the number card on your
telephone
9. Insert the Memory key card on your telephone
Write your telephone number on
the number card.
Place the number card into the
slot underneath the handset cra-
dle on the on the telephone.
Gently bend the clear plastic lens
and place it on top of the number
card in the slot.
This card contains the feature names for the dedi-
cated keys and label identiÞcation spaces for the
eight programmable memory keys.
Place the card into the memory key card slot on
the telephone.
Gently bend the clear plastic lens and place it on
top of the memory key card in the slot.
For more information on programming memory
keys, refer to Memory keys on page 21

7
Basic Installation
To avoid potential electrical shock hazard to personnel or damage
to the telephone, use onlythe manufacturer-supplied equipment
and installation procedures. SpeciÞcally, use only 4 conductor
modular teledapt plug/cords with this product, and an AC trans-
former that is CSA/UL or CSA-NRTL/C approved Class 2 level
C, rated as follows:
For North American Markets AC voltage 110-120V,Input: 120VAC,
60Hz, 10W and Output: 16V AC, 250mA.
Substitution of non-approved equipment will void the Aastra
Telecom Inc., warranty. For more information about installation
and safety concerns, call 1-800-574-1611.

8
Making and Answering Calls
Making and Answering Calls
Making a call
With your telephone you can make and answer calls using your handset or Pfor
speakerphone capabilities. A headset attachment can also be used with your tele-
phone, refer to page 28 . You can use the 9120 to simply make a regular call, or you can
predial a telephone number to ensure it is correct before it is dialed out. Follow the
procedures below to make a regular or predialed call.
Note: If you have turned on the live dial pad option, you will not have to lift the
handset or press any buttons after entering the number. Refer to Selecting the
dial pad mode on page 26.
When you use P, Dor lift the handset rather than using a line key to make
a call, the prime line is automatically selected. The default prime line is Line 1. If you
want to change the prime line to Line 2, see Changing the Prime Line on page 14.
Answering a Call
When you subscribe to the Caller ID service from your telephone company, Caller ID
information is sent from the telephone company to your 9120 telephone between the
Þrst and second ring. Therefore, if you want the telephone number of the incoming
call to appear on the display and in the Callers List, you must wait until the informa-
tion appears on the display before answering the telephone.
If you lift the handset or press Pwhen both lines are ringing, the line that was
ringing Þrst is automatically answered.
Using the Hold Key
Note: The 9120 automatically releases a call on hold when a person on an extension
telephone on the same line picks up the call. If you don’t hang up the handset
after you have put a call on hold and that call is picked up by someone at
To make a regular call: To make a predialed call:
1. Lift the handset or press either
Por Y.
1. Enter the number using the dial pad.
2. Enter the number using the dial pad. 2. Lift the handset or press either
P,Dor Y.
To answer a call:
1. Lift the handset, press P or press the key for the line you want to answer .
To put a call on hold and take a call off hold:
1. Make or answer a call.
2. Press O. Line 1 held or Line 2 held appears on the display and the line indi-
cator light ßashes.
Note: You won’t lose the call if you hang up the handset.
3. To retrieve the call, press O,Por Y. If you don’t retrieve the call
within 15 minutes, the call is automatically dropped.

9
Making and Answering Calls
another extension, the call is taken off hold but remains connected to your tele-
phone. If this happens, any background noise from your area will be heard by
the caller and the person at the other extension.
Switching between two lines
Using the Conference key
Note: You can speak privately with one particular caller by pressing that caller’s line
key. This automatically puts the other caller on hold. You can re-establish the
conference by pressing E.
Extension in Use
When you are on a call and someone on an extension telephone picks up the handset,
the set indicator light comes on if the person on the extension is using your line. The
light remains on and the message Extension in use appears until the person at the
other extension hangs up.
When another extension is using a line, the line indicator light for that line (located
beside the line key) is illuminated. Line indicator lights let you know if a line is avail-
able for you to use. Also see Extension in Use on page 28.
Making a Handsfree call
You don’t have to use the handset to use your telephone. Instead, you can use Hands-
free mode to place a call, or you can switch to Handsfree mode while a call is in
progress.
To put a call on hold and make or answer a second call:
1. Make or answer a call on one line.
2. To make or answer a second call on the other line, press the second line key. This
automatically puts the original line on hold.
3. To hold one line automatically and speak on the other, press the line keys alter-
nately.
4. To end a call which is not on hold, press Nor hang up.
To join two calls in a Conference:
1. Make or answer a call on one of the lines.
2. Press Oto place the Þrst call on hold.
3. Make or answer a call on the second line.
4. Once you have callers on both lines, press E.
To dial without picking up the handset: To switch to a Handsfree call:
1. Press Por Y.1. Lift the handset.
2. Enter the number using the dial pad. 2. Dial a number using the dial pad.
3. When the call is over, press N.4.3. When the call is answered, press
P.

10
Making and Answering Calls
Muting a Handsfree call
You can turn off the microphone so that the caller can’t hear you but you can still hear
the caller. Muting a call only works when you are in Handsfree mode.
Using the Redial List
The Redial List stores the last ten numbers you dialed. When you press Cthe
last number you called appears on the screen. If you are off hook and press C,
the telephone will automatically dial the last number called.
You can scroll through the list to view the other numbers.
4. Hang up the handset.
5. When the call is over, press N.
To mute a handsfree call:
1. Press P.
2. Without lifting the handset, make a call.
3. To turn off the microphone, press P. You can hear your caller but your
caller cannot hear you. The light beside Pßashes. The display shows
Microphone muted.
4. To speak to your caller, press Pagain. Each time you press P, you
turn the microphone on or off.
5. When the call is over, press N.
To mute headset call:
1. Press P.
2. Without lifting the handset, make a call.
3. To turn off the microphone, press P. You can hear your caller but your
caller cannot hear you. The display shows Microphone muted.
4. To speak to your caller, press Pagain. Each time you press P, you
turn the microphone on or off.
5. When the call is over, press N.
To make a call from the Redial List:
1. Press C. The display shows the last number you dialed.
2. Use Vor Wto scroll through the list to view the other numbers.
3. When the number is displayed, lift the handset or press either D, P
or Y.
To dial without picking up the handset: To switch to a Handsfree call:

11
Making and Answering Calls
There may be times when you want to delete the contents of the Redial List. For exam-
ple, if you have dialed a personal number such as a password or your calling card
number, you may not want it to appear in the list where anyone can see it.
Note: You cannot delete individual entries in the Redial List.
Call Waiting ID†
The 9120 is capable of displaying Caller ID information of a second incoming call
while you have a call in progress. When you are on a call and you hear the Call Wait-
ing tone, the Call Waiting information is displayed as shown below.
If you decide you want to speak to the new caller, simply press B. Your Þrst call
will not be disconnected. You may switch between callers as often as you like by press-
ing B. When you press Band see a caller’s IdentiÞcation information but
only hear a dial tone, it means that the caller has hung up. Your second call will be
stored in the Callers List even if it is not answered. For more information about stored
calls, see Callers List on page 18.
Note: The Call Waiting ID display option must be enabled in order to see the Call
Waiting ID information on the display.
To delete the Redial List:
1. Press C.
2. Press Ltwice. The entire Redial List is deleted.
† You must subscribe to your telephone company for the Call Waiting with Calling ID service.
Incoming caller's information
(Caller One) is displayed.
CALLER NE
555-1234
CALLER NE
555-1234
When you hear the Call Waiting tone,
Caller Two's information is displayed.
CALLER NE
555-1234
CALLER TW 
555-5678

12
Making and Answering Calls
Turning the display of Call Waiting ID on or off
You can choose whether or not Call Waiting ID is displayed on your telephone for Line
1 and Line 2 .
Note: Turning the display of Call Waiting ID on or off does not turn the feature itself
on or off. When the Call Waiting display is turned off, you will still hear the Call
Waiting tone when a Call Waiting call comes in, but the identiÞcation informa-
tion for the Call Waiting caller will not appear on your display screen. Contact
your local telephone company to subscribe or unsubscribe to Caller ID or Call
Waiting ID services.
Changing the display language
For changing business requirements, you may wish to change the language of your
display messages and prompts. There are three language choices available for your
telephone (English, French and Spanish).
Setting the date and time
If you subscribe to the Caller ID service from your telephone company, the date and
time are set automatically after you receive your Þrst incoming call. If you do not sub-
scribe, you must set the date and time manually.
To turn Call Waiting on or off:
1. Press I.
2. Press 11 or use Vor Wto scroll to Setup Option 11.
3. Press •to enter Call Waiting ID.
4. Press Y.
5. Press •to turn the Call Waiting ID feature on or press £to turn the feature off.
6. Press N.
7. Repeat these steps for the other telephone line.
To change the display language:
1. Press I.
2. Press 01or use Vto scroll to Option 01.
3. Press *to enter Language choice.
4. Use Vto scroll to the desired language.
5. Press •to select the displayed language.
6. Press N.
To set the date and time:
1. Press I.
2. Press 09or use Vor Wto scroll to Option 09.
3. Press *to enter the time/date.
4. Follow the instructions on the display.
5. Press N.

13
Making and Answering Calls
To resume the automatic date and time setting (if the date and time has been set man-
ually), disconnect the power supply, then re-connect it. After your Þrst incoming call,
the date and time are automatically set if you subscribe to the Caller ID service from
your telephone company.
Turning the ringer on and off
Note: Do not lift the handset while you are turning the ringer on or off.
Setting the ring tone and ringer volume
You can choose one of four different ring tones and set the ringer volume for each line.
Controlling the ringer volume
While the telephone is ringing on one line, you can press the left or right side of the
volume bar Rto adjust the ringer volume for that line.
Controlling the handset volume
While you are on the telephone, you can press the left or right side of the volume bar
Rto adjust the handset volume. The handset volume returns to normal after
you have completed your call.
Controlling the speaker volume
While you are listening through the speaker, you can press the left or right side of the
volume bar Rto adjust the speaker volume. The speaker volume remains at the
volume you last selected until the next time you change it.
To turn the ringer on: To turn the ringer off:
1. Press R. 1. Press R.
2. Press Y.2.Press Y.
3. Press the right side of R. Con-
tinue pressing the right hand side until
you reach the desired ring volume.
3. Press the left side of R. Con-
tinue pressing the left hand side
until the ringer is off.
To set the ring tone and volume:
1. Make sure that the ringer is turned on.
2. Press I.
3. Press 04 or use Vor WTo scroll to Option 04.
4. Press *to enter Select ring tone.
5. Select a Y.
6. Press Vand follow the instructions on the display.
When picking the ring tone, press Rto adjust the volume.
7. Press Kto end only when you are satisÞed with ring tone and ringer volume.
8. If required, repeat these instructions for the other line.
9. Press N.

14
Making and Answering Calls
Changing the Prime Line
The prime line is the line that is automatically selected when you lift the handset or
press or Por D. The default setting for prime line is Line 1. You can select
either line as your prime line.
Clear Message Lamp
There may be times when Message Waiting appears on the display when there are no
more Voice Mail messages. You can turn the display message off using the Clear Mes-
sage Waiting feature.
Note: This only applies when you subscribe to Voice Mail services from your tele-
phone company.
To change the prime line:
1. Press I.
2. Press 10 or use Vor Wto scroll to option 10.
3. Press *to change the prime line. Pressing *allows you to toggle between the
two lines.
4. Press N.
To clear message waiting:
1. Press I.
2. Press 02or use Vor Wto scroll to Option 02.
3. Press *to enter Clear msg. lamp.
4. Select Y.
5. If required, repeat these instructions for the other line.

15
Directory
Directory
The 9120 telephone directory can store the names and telephone numbers of your
business associates, clients, contacts, friends and relatives.
Directory names
There is a maximum of 100 entries in your Directory. Names are sorted alphabetically
starting with their Þrst character. If you want your Directory sorted by the last name,
enter the last name Þrst. If you do not enter a name, the Directory record is sorted by
telephone number. The Directory records with only a telephone number are numeri-
cally sorted at the beginning of the Directory.
Saving numbers and names to the Directory
To save a new number and name: To save from the display:
1. Press K.1. Ensure that a number is on the dis-
play.(For example, access the
Redial List or the Callers List).
2. Press J.2. Press K.
3. Enter the number using the dial pad.
You can enter a maximum of 24 digits.
Note: If you require a pause (for
example, between a telephone num-
ber and an access code), press O
where you want the pause.
3. Press J. If the name is dis-
played with the number, both are
now saved in the Directory.
4. Press K. Only the number is stored
at this point.
4. If no name is displayed, you are
prompted to enter one. If you do
not want a name, go to step 5. To
enter a name, use the dial pad. (See
Entering Names on page 16.)
5. Use the dialpad to enter a name. (See
Entering Names on page 16.)
5. Press K.
6. Press K.
7. Press N.

16
Directory
Saving an active call into the Directory
Saving a memory key entry to the Directory
Entering Names
You can program names to correspond with numbers you have entered into the Direc-
tory or a memory key. The following paragraphs explain how to enter letters using the
dial pad. Before you can use the dial pad to enter names, you must Þrst save or edit a
number in the Directory or memory key.
To program a name, Þnd the dial pad key that has the Þrst character of the name. Keep
watching the display as you press the key until that character appears on the display.
Press a different dial pad key for the next character. If the next character is on the same
key, press U to move to the next space or wait a few seconds and it will automatically
advance to the next space. To insert a space, press U. To backspace and erase a mis-
take, press Tand L. For example, to enter the name RUTH press these keys:
‡‡‡, °°, U, °, ››.
If you wish to change a digit or letter after you have entered it, press Tto erase it .
⁄, - . 1 ¤A B C 2 ‹D E F 3
›G H I 4 fiJ K L 5 flM N O 6
‡P Q R S 7 °T U V 8 ·W XY Z
•* ‚0£#
Making a call from the Directory
Note: To leave the Directory at any time, press Jor N.
To save an active call:
1. Answer or make a call.
2. Press K.
3. Press J. If the name was displayed with the number, both are now saved
in the Directory.
4. If no name is displayed, you are prompted to enter one. If you do not want to
enter a name, go to step 5. To enter a name, use the dial pad.
5. Press K.
6. Press N.
To save a memory key entry into the Directory:
1. Press the desired memory key. Ensure the live dial pad option is turned off.
2. Press K.
3. Press J. If the name was displayed with the number, both are now saved in
the Directory. If no name was displayed, only the number is saved to the directory.
To make a call from the Directory:
1. Press J.
2. Press Vor Wor use the dial pad to Þnd the item you want to dial out.
3. Lift the handset or press either P, Dor Y.
4. To end the call, press Nor hang up.

17
Directory
Finding items in the Directory
Editing in the Directory
Deleting items from the Directory
To find items in the Directory:
1. To see the Directory List heading, press J.
2. Use the Wand Vto look at each individual directory entry one at a time.
3. To leave the Directory at any time, press Jor N.
To edit a number and/or name in the Directory:
1. Press J.
2. Press Vor Wto Þnd the item you want to edit.
3. To begin editing, press T.
4. If you do not want to change the number, go to step 5. To backspace and erase
digits, press T. To add digits, use the dial pad.
5. Press K.
6. If you do not want to change the name, go to step 7. To change or add to the
name, use Tand the dial pad. (See Entering Names on page 16.)
Note: If you edit the wrong item or want to quit without saving changes, press
Jor N.
7. Press K.
8. Press N.
To delete individual items:
1. Press J.
2. Press VWto Þnd the item you want to delete.
3. Press Ltwice. You are still in the Directory.
4. Press Nor Jto exit the Directory at any time.
To delete all items:
1. Press J.
2. Press L.
3. Press Lagain to conÞrm deletion of the entire Directory.
4. Press N.