ABB Welcome M2300 User manual

—
VER: 1.3 | 02.20.2017
ABB Welcome®
M2300
System controller

ABB Welcome®
— 2 —
Pos: 4 /Busch-Jaege r (Neustrukt ur)/Modul-Struktu r/Online-Doku mentation/Inhaltsve rzeichnis ( --> Für alle Dokumente <--)/In haltsverzeichnis @ 19\mod_13 20649044386_1 5.docx @ 109 653 @ @ 1
1 Safety ......................................................................................................... 3
2 Intended use ............................................................................................... 3
3 Environment ................................................................................................ 3
3.1 ABB devices ..................................................................................... 3
4 Operation .................................................................................................... 4
4.1 Control elements .............................................................................. 4
4.2 Operating modes .............................................................................. 5
5 Technical data ............................................................................................. 6
6 Mounting and installation ............................................................................. 7
6.1 Requirements for the electrician ........................................................ 7
6.2 General installation instructions ......................................................... 7
6.3 Mounting .......................................................................................... 8

ABB Welcome®
— 3 —
1 Safety
Warning
Electric voltage!
Direct or indirect contact with live components can cause dangerous
currents to flow through the body, which may result in electric shock,
burns or even death.
- Always disconnect the main power supply prior to installation and/or
disassembly.
- Work on the 110 V - 240 V supply system must be performed only
by qualified personnel.
2 Intended use
This device is an integral part of the ABB Welcome door communication system and operates exclusively with components from this
system.The device must only be installed on mounting rails according to DIN EN 500022.
3 Environment
Consider the protection of the environment!
Used electric and electronic devices must not be disposed of with
household waste.
– The device contains valuable raw materials that can be recycled
and should be disposed of at an appropriate recycling facility.
3.1 ABB devices
All packaging materials and devices from ABB bear the markings and test seals for proper disposal. Always dispose of the packaging
material, electric devices and their components via authorized recycling facilities or disposal companies.

ABB Welcome®
— 4 —
4 Operation
4.1 Control elements
Fig.
1
: Overview of control buttons
No.
Functions
1
Bus in or out
2
Operating mode settings
See chapter "Operating modes" for details.
3
Operating status indicating LED
- Ready for operation - Fault
4
Power supply
1
2
4
N
L
100~240V
3

ABB Welcome®
— 5 —
4.2 Operating modes
Fig.
2
:
“One on” mode:
When there is an incoming call, all indoor stations in the same apartment ring together,
but only the master indoor station switches on the screen.
“All on” mode:
When there is an incoming call, all indoor stations in the same apartment ring and switch
on their screens at the same time.
One on:
All on:

ABB Welcome®
— 6 —
5 Technical data
Designation
Value
Operating temperature
-13 °F to +131 °F
Storage temperature
-40 °F to +158 °F
Protection
IP 20
Single-wire clamps
2 x 22 AWG - 2 x 18 AWG
Fine-wire clamps
2 x 22 AWG - 2 x 18 AWG
Mains voltage
100 V - 240 V, 50/60 Hz, 1.0 A
Bus voltage
28 V ± 2 V DC, 1.2 A
Size
8 U

ABB Welcome®
— 7 —
6 Mounting and installation
Warning
Electric voltage!
Direct or indirect contact with live components can cause dangerous
currents to flow through the body, which may result in electric shock,
burns or even death.
- Always disconnect the main power supply prior to installation and/or
disassembly.
- Work on the 110 V - 240 V supply system must be performed only
by qualified personnel.
6.1 Requirements for the electrician
Warning
Electric voltage!
Install the device only if you have the necessary qualifications.
- Incorrect installation endangers your life and that of the user of the
electrical system.
- Incorrect installation can cause serious damage to property, e.g.,
due to fire.
The minimum necessary expert knowledge and requirements for the
installation are as follows:
- Apply the "five safety rules" (DIN VDE 0105, EN 50110):
1. Disconnect from power.
2. Secure against being re-connected.
3. Ensure there is no voltage.
4. Connect to earth.
5. Cover or barricade adjacent live parts.
- Wear suitable personal protective clothing.
- Use only suitable tools and measuring devices.
- Check the type of supply network (TN system, IT system, TT
system) to secure the following power supply conditions (classic
connection to ground, protective earthing, necessary additional
measures, etc.).
6.2 General installation instructions
- Terminate all branches of the wiring system via a connected bus device (e.g., indoor station, outdoor station, system device).
- Do not install the system controller directly next to the bell transformer or other power supplies (to avoid interference).
- Do not install the wires of the system bus together with 100 V - 240 V wires.
- Do not use common cables for the connecting wires of the door openers and wires
of the system bus.
- Avoid bridges between different cable types.
- Use only two wires for the system bus in a four-core or multi-core cable.
- When looping, never install the incoming and outgoing bus inside the same cable.
- Never install the internal and external bus inside the same cable.

ABB Welcome®
— 8 —
6.3 Mounting
The device M2300 must only be installed on mounting rails according to DIN EN 500022.

1SXU460062M0201, June 2018
—
ABB Inc.
Electrification Products
860 Ridge Lake Blvd.
Memphis, TN 38120
www.abb.com/door-entry-system-us
abbwelc[email protected].com
Customer Service: 800-816-7809
7:00 a.m. - 5:30 p.m., CST, Monday-Friday
[e-mail]
Technical Support: 888-385-1221, Option 1
7:00 a.m. - 5:00 p.m., CST, Monday-Friday
[email protected]m
—
We reserve the right to make technical
changes or modify the contents of this
document without prior notice. With regard
to purchase orders and/or contracts, the
agreed particulars shall prevail. ABB Inc.
does not accept any responsibility what-
soever for potential errors or possible lack
of information in this document.
We reserve all rights in this document and in
the subject matter and illustrations contained
therein. Any reproduction, disclosure to third
parties or utilization of its contents - in whole
or in parts - is forbidden without prior written
consent of ABB Inc.
© Copyright 2018 ABB. All rights reserved.