ABB Relion 620 Series User manual

Relion® 620 series
Transformer Protection and Control
RET620
DNP3 Point List Manual

Document ID: 1MRS757660
Issued: 2013-05-07
Revision: A
Product version: 2.0
© Copyright 2013 ABB. All rights reserved

Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third
party, nor used for any unauthorized purpose.
The software or hardware described in this document is furnished under a license
and may be used, copied, or disclosed only in accordance with the terms of such
license.
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or
product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
http://www.abb.com/substationautomation

Disclaimer
The data, examples and diagrams in this manual are included solely for the concept
or product description and are not to be deemed as a statement of guaranteed
properties. All persons responsible for applying the equipment addressed in this
manual must satisfy themselves that each intended application is suitable and
acceptable, including that any applicable safety or other operational requirements
are complied with. In particular, any risks in applications where a system failure and/
or product failure would create a risk for harm to property or persons (including but
not limited to personal injuries or death) shall be the sole responsibility of the
person or entity applying the equipment, and those so responsible are hereby
requested to ensure that all measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested
to notify the manufacturer. Other than under explicit contractual commitments, in
no event shall ABB be responsible or liable for any loss or damage resulting from
the use of this manual or the application of the equipment.

Conformity
This product complies with the directive of the Council of the European
Communities on the approximation of the laws of the Member States relating to
electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning
electrical equipment for use within specified voltage limits (Low-voltage directive
2006/95/EC). This conformity is the result of tests conducted by ABB in
accordance with the product standards EN 50263 and EN 60255-26 for the EMC
directive, and with the product standards EN 60255-1 and EN 60255-27 for the low
voltage directive. The product is designed in accordance with the international
standards of the IEC 60255 series.

Table of contents
Section 1 Introduction.......................................................................9
This manual........................................................................................9
Intended audience..............................................................................9
Product documentation.......................................................................9
Product documentation set............................................................9
Document revision history...........................................................10
Related documentation................................................................10
Symbols and conventions.................................................................10
Symbols.......................................................................................10
Document conventions................................................................11
Functions, codes and symbols....................................................12
Section 2 DNP3 data mappings.....................................................19
Overview...........................................................................................19
Supported functions..........................................................................19
Binary inputs.....................................................................................22
System functions.........................................................................22
CTRL.LLN0 Local/remote state (also present in DNP IIN-
bits).........................................................................................22
LD0.LLN0 Settings supervision..............................................22
Switchgear functions...................................................................23
CTRL.Cxxxxx1 Circuit breaker (1) CB object and failure
protection................................................................................23
CTRL.Cxxxxx2 Circuit breaker (2) CB object and failure
protection................................................................................23
CTRL.Dxxxxx1 Controllable disconnector (1)........................24
CTRL.Dxxxxx2 Controllable disconnector (2)........................24
CTRL.Dxxxxx3 Controllable disconnector (3)........................24
CTRL.Dxxxxx4 Controllable disconnector (4)........................25
CTRL.Exxxxx1 Controllable earth switch (1)..........................25
CTRL.Exxxxx2 Controllable earth switch (2)..........................25
Sensors and monitoring functions...............................................26
LD0.ARCSARC1 Fault arc protection stage 1........................26
LD0.ARCSARC2 Fault arc protection stage 2........................26
LD0.ARCSARC3 Fault arc protection stage 3........................26
LD0.SSCBR1 Circuit-breaker condition monitoring................26
LD0.SSCBR2 Circuit-breaker condition monitoring................27
LD0.TCSSCBR1 Trip circuit supervision (1)..........................27
LD0.TCSSCBR2 Trip circuit supervision (2)..........................27
Automatic control functions.........................................................28
Table of contents
RET620 1
Point List Manual

LD0.OLATCC1 On-load tap changer controller......................28
Metering and measurand functions.............................................28
LD0.CMMXU1 Phase currents (1) limit supervision...............28
LD0.CMMXU2 Phase currents (2) limit supervision...............29
LD0.RESCMMXU1 Residual current limit supervision...........29
LD0.RESCMMXU2 Residual current limit supervision...........29
LD0.VMMXU1 Three-phase voltage limit supervision............29
LD0.RESVMMXU1 Residual voltage limit supervision...........30
Protection functions.....................................................................30
LD0.LEDPTRC1 Global protection signals.............................30
LD0.TRPPTRC1 Global conditioning (1)................................30
LD0.TRPPTRC2 Global conditioning (2)................................30
LD0.DEFLPDEF1 Directional earth-fault protection - low
stage 1....................................................................................31
LD0.DEFLPDEF2 Directional earth-fault protection - low
stage 2....................................................................................31
LD0.DEFHPDEF1 Directional earth-fault protection -
high stage 1............................................................................31
LD0.DPHLPDOC1 Three-phase directional overcurrent
protection - low stage (1)........................................................31
LD0.DPHHPDOC1 Three-phase directional overcurrent
protection - high stage (1)......................................................31
LD0.EFLPTOC1 Non-directional earth-fault and
sensitive earth-fault protection - low stage 1..........................32
LD0.EFLPTOC2 Non-directional earth-fault and
sensitive earth-fault protection - low stage 2..........................32
LD0.EFHPTOC1 Non-directional earth-fault and
sensitive earth-fault protection - high stage 1.........................32
LD0.EFHPTOC2 Non-directional earth-fault and
sensitive earth-fault protection - high stage 2.........................32
LD0.PHHPTOC1 Phase overcurrent protection - high
stage 1 ...................................................................................33
LD0.PHHPTOC2 Phase overcurrent protection - high
stage 2 ...................................................................................33
LD0.PHIPTOC1 Phase overcurrent protection -
instantaneous stage 1 ...........................................................33
LD0.PHIPTOC2 Phase overcurrent protection -
instantaneous stage 2 ...........................................................33
LD0.PHLPTOC1 Phase overcurrent protection - low
stage 1 ...................................................................................33
LD0.PHLPTOC2 Phase overcurrent protection - low
stage 2 ...................................................................................34
LD0.PHPTUC1 Loss of phase (undercurrent) protection
(1)...........................................................................................34
LD0.PHPTUC2 Loss of phase (undercurrent) protection
(2)...........................................................................................34
Table of contents
2RET620
Point List Manual

LD0.PHPTOV1 Phase overvoltage protection - stage 1........34
LD0.PHPTOV2 Phase overvoltage protection - stage 2........34
LD0.PHPTOV3 Phase overvoltage protection - stage 3........35
LD0.ROVPTOV1 Residual overvoltage protection (1)...........35
LD0.ROVPTOV2 Residual overvoltage protection (2)...........35
LD0.ROVPTOV3 Residual overvoltage protection (3)...........35
LD0.NSPTOC1 Negative-sequence overcurrent
protection (1)..........................................................................35
LD0.NSPTOC2 Negative-sequence overcurrent
protection (2)..........................................................................36
LD0.NSPTOV1 Negative-sequence overvoltage
protection - stage 1.................................................................36
LD0.NSPTOV2 Negative-sequence overvoltage
protection - stage 2.................................................................36
LD0.PHPTUV1 Phase undervoltage protection - stage
1.............................................................................................36
LD0.PHPTUV2 Phase undervoltage protection - stage
2.............................................................................................36
LD0.PHPTUV3 Phase undervoltage protection - stage
3.............................................................................................37
LD0.PSPTUV1 Positive-sequence undervoltage
protection - stage 1.................................................................37
LD0.PSPTUV2 Positive-sequence undervoltage
protection - stage 2.................................................................37
LD0.INPHAR1 Three-phase inrush detection........................37
LD0.FRPFRQ1 Frequency protection (1)...............................37
LD0.FRPFRQ2 Frequency protection (2)...............................38
LD0.FRPFRQ3 Frequency protection (3)...............................38
LD0.HREFPDIF1 High-impedance restricted earth-fault
protection (1)..........................................................................38
LD0.HREFPDIF2 High-impedance restricted earth-fault
protection (2)..........................................................................39
LD0.LREFPDIF1 Low-impedance restricted earth-fault
protection (1)..........................................................................39
LD0.LREFPDIF2 Low-impedance restricted earth-fault
protection (2)..........................................................................39
LD0.OEPVPH1 Voltage per hertz protection (1)....................39
LD0.OEPVPH2 Voltage per hertz protection (2)....................39
LD0.TR2PDIF1 Transformer differential protection................40
LD0.T2PTTR1 Thermal protection (2)....................................40
Power quality functions................................................................40
LD0.LSHDPFRQ1 Load-shedding - instance 1......................40
LD0.LSHDPFRQ2 Load-shedding - instance 2......................40
LD0.LSHDPFRQ3 Load-shedding - instance 3......................41
LD0.LSHDPFRQ4 Load-shedding - instance 4......................41
Table of contents
RET620 3
Point List Manual

LD0.LSHDPFRQ5 Load-shedding - instance 5......................41
LD0.LSHDPFRQ6 Load-shedding - instance 6......................41
Protection related functions.........................................................42
DR.RDRE1 Disturbance recorder..........................................42
LD0.SECRSYN1 Synchrocheck ............................................42
LD0.CCRDIF1 Current circuit failure protection.....................42
LD0.CCRDIF2 Current circuit failure protection.....................42
LD0.CTSRCTF1 Current circuit supervision for
transformers (1)......................................................................42
LD0.SEQRFUF1 Fuse failure protection................................43
Generic functions.........................................................................43
LD0.MAPGAPC1 Multipurpose analog protection
function (1).............................................................................43
LD0.MAPGAPC2 Multipurpose analog protection
function (2).............................................................................43
LD0.MAPGAPC3 Multipurpose analog protection
function (3).............................................................................43
LD0.MAPGAPC4 Multipurpose analog protection
function (4).............................................................................43
LD0.MAPGAPC5 Multipurpose analog protection
function (5).............................................................................44
LD0.MAPGAPC6 Multipurpose analog protection
function (6).............................................................................44
LD0.MAPGAPC7 Multipurpose analog protection
function (7).............................................................................44
LD0.MAPGAPC8 Multipurpose analog protection
function (8).............................................................................44
LD0.MAPGAPC9 Multipurpose analog protection
function (9).............................................................................44
LD0.MAPGAPC10 Multipurpose analog protection
function (10)...........................................................................45
LD0.MAPGAPC11 Multipurpose analog protection
function (11)...........................................................................45
LD0.MAPGAPC12 Multipurpose analog protection
function (12)...........................................................................45
LD0.MVGAPC1 Multipurpose binary inputs (1)......................45
LD0.MVGAPC2 Multipurpose binary inputs (2)......................46
LD0.MVGAPC3 Multipurpose binary inputs (3)......................46
LD0.MVGAPC4 Multipurpose binary inputs (4)......................46
LD0.SPCGGIO1 Multipurpose binary outputs - status
(1)...........................................................................................47
LD0.SPCGGIO2 Multipurpose binary outputs - status
(2)...........................................................................................47
LD0.SPCGGIO3 Multipurpose binary outputs - status
(3)...........................................................................................48
Table of contents
4RET620
Point List Manual

LD0.SPCRGGIO1 Multipurpose binary outputs - status
(1)...........................................................................................48
LD0.FKEYGGIO1 LED states................................................49
Physical and raw I/O data............................................................50
LD0.XGGIO105 Physical I/O..................................................50
LD0.XHBGGIO105 Physical I/O.............................................50
LD0.XRGGIO105 Alarm/warning...........................................51
LD0.XBRGGIO130 Alarm/warning - physical outputs............51
LD0.XGGIO100 Physical I/O..................................................51
LD0.XGGIO110 Physical I/O..................................................51
Binary outputs...................................................................................52
System functions.........................................................................52
LD0.LLN0/LPHD1 Reset indications and LEDs, reset
device.....................................................................................52
LD0.DNPGGIO1 Parameter setting group control.................53
Switchgear functions...................................................................53
CTRL.CBCSWI1 Circuit breaker control ...............................53
CTRL.CBCSWI2 Circuit breaker control ...............................53
CTRL.DCCSWI1 Controllable disconnector (1) control .........53
CTRL.DCCSWI2 Controllable disconnector (2) control..........53
CTRL.DCCSWI3 Controllable disconnector (3) control..........54
CTRL.DCCSWI4 Controllable disconnector (4) control..........54
CTRL.ESCSWI1 Controllable earth switch (1) control ..........54
CTRL.ESCSWI2 Controllable earth switch (2) control ..........54
Sensors and monitoring functions...............................................54
LD0.SSCBR1 Reset signals of CB condition monitoring........54
LD0.SSCBR2 Reset signals of CB condition monitoring........55
Metering and measurand functions.............................................55
LD0.PEMMXU1 Reset accumulated energy values...............55
Protection functions.....................................................................55
LD0.LSHDPFRQ1 Loadshedding controls (1)........................55
LD0.LSHDPFRQ2 Loadshedding controls (2)........................55
LD0.LSHDPFRQ3 Loadshedding controls (3)........................56
LD0.LSHDPFRQ4 Load shedding controls (4).......................56
LD0.LSHDPFRQ5 Load shedding controls (5).......................56
LD0.LSHDPFRQ6 Load shedding controls (6).......................56
Protection related functions.........................................................56
DR.RDRE1 Disturbance recorder..........................................56
Generic functions.........................................................................57
LD0.SPCGGIO1 Multipurpose binary outputs (1)..................57
LD0.SPCGGIO2 Multipurpose binary outputs (2)..................57
LD0.SPCGGIO3 Multipurpose binary outputs (3)..................58
LD0.SPCRGGIO1 Multipurpose binary outputs (1)................59
Table of contents
RET620 5
Point List Manual

LD0.SRGAPC1 Multipurpose binary outputs - flip-flop
resets (1)................................................................................59
LD0.SRGAPC2 Multipurpose binary outputs - flip-flop
resets (2)................................................................................60
Analog inputs....................................................................................60
System functions.........................................................................60
CTRL.LLN0 Local remote station off......................................60
LD0.LPHD1 System values....................................................61
LD0.LEDGGIO1 LHMI LED indications (3 states)..................61
LD0.DNPGGIO1 Active parameter setting group...................61
Switchgear functions...................................................................62
CTRL.CBCSWI1 CB 4-pole (2 bit) position value..................62
CTRL.CBCSWI2 CB 4-pole (2 bit) position value..................62
CTRL.DCSXSWI1 Disconnector 1, 4-pole (2 bit)
position values........................................................................62
CTRL.DCSXSWI2 Disconnector 2, 4-pole (2 bit)
position values........................................................................62
CTRL.DCSXSWI3 Disconnector 3, 4-pole (2 bit)
position values........................................................................62
CTRL.DCSXSWI4 Disconnector 4, 4-pole (2 bit)
position values........................................................................63
CTRL.DCXSWI1 Controllable disconnector 1, 4-pole (2
bit) position values..................................................................63
CTRL.DCXSWI2 Controllable disconnector 2, 4-pole (2
bit) position values..................................................................63
CTRL.DCXSWI3 Controllable disconnector 3, 4-pole (2
bit) position values..................................................................63
CTRL.DCXSWI4 Controllable disconnector 4, 4-pole (2
bit) position values..................................................................63
CTRL.ESSXSWI1 Earth switch 1, 4-pole (2 bit) position
values.....................................................................................64
CTRL.ESSXSWI2 Earth switch 2, 4-pole (2 bit) position
values.....................................................................................64
CTRL.ESXSWI1 Controllable earth switch 1, 4-pole (2
bit) position values..................................................................64
CTRL.ESXSWI2 Controllable earth switch 2, 4-pole (2
bit) position values..................................................................64
Sensors and monitoring functions...............................................65
LD0.SSCBR1 Circuit-breaker condition monitoring
values.....................................................................................65
LD0.SSCBR2 Circuit-breaker condition monitoring
values.....................................................................................65
LD0.TPOSSLTC1 Tap changer position value.......................66
Metering and measurand functions.............................................66
LD0.CMMXU1 Phase currents (1)..........................................66
Table of contents
6RET620
Point List Manual

LD0.CMMXU2 Phase currents (2)..........................................66
LD0.CSMSQI1 Sequence of currents....................................66
LD0.RESCMMXU1 Residual current (1)................................67
LD0.RESCMMXU2 Residual current (2)................................67
LD0.VMMXU1 Voltage measurement ...................................67
LD0.RESVMMXU1 Residual voltage (1)................................67
LD0.VSMSQI1 Sequence of voltage measurement...............68
LD0.PEMMTR1 Power measurement and accumulated
power values..........................................................................68
Protection functions.....................................................................68
LD0.T2PTTR1 Temperature protection values (2).................68
Protected related functions..........................................................69
DR.RDRE1 Disturbance recorder values...............................69
LD0.SECRSYN1 Synchrocheck line and bus state................69
Physical and raw I/O data............................................................69
LD0.XRGGIO105 RTD inputs................................................69
LD0.XBRGGIO130 RTD inputs..............................................70
Section 3 DNP3 protocol implementation.......................................71
DNP3 device profile..........................................................................71
DNP3 implementation table..............................................................73
Section 4 Glossary.........................................................................77
Table of contents
RET620 7
Point List Manual

8

Section 1 Introduction
1.1 This manual
The point list manual describes the outlook and properties of the data points
specific to the IED. The manual should be used in conjunction with the
corresponding communication protocol manual.
1.2 Intended audience
This manual addresses the communication system engineer or system integrator
responsible for pre-engineering and engineering for communication setup in a
substation from an IED perspective.
The system engineer or system integrator must have a basic knowledge of
communication in protection and control systems and thorough knowledge of the
specific communication protocol.
1.3 Product documentation
1.3.1 Product documentation set
The application manual contains application descriptions and setting guidelines
sorted per function. The manual can be used to find out when and for what purpose
a typical protection function can be used. The manual can also be used when
calculating settings.
The communication protocol manual describes a communication protocol
supported by the IED. The manual concentrates on vendor-specific implementations.
The engineering guide provides information for IEC 61850 engineering of the
protection IEDs with PCM600 and IET600. This guide concentrates especially on
the configuration of GOOSE communication with these tools. The guide can be
used as a technical reference during the engineering phase, installation and
commissioning phase, and during normal service. For more details on tool usage,
see the PCM600 documentation.
The engineering manual contains instructions on how to engineer the IEDs using
the different tools in PCM600. The manual provides instructions on how to set up a
PCM600 project and insert IEDs to the project structure. The manual also
1MRS757660 A Section 1
Introduction
RET620 9
Point List Manual

recommends a sequence for engineering of protection and control functions, LHMI
functions as well as communication engineering for IEC 61850 and other
supported protocols.
The installation manual contains instructions on how to install the IED. The
manual provides procedures for mechanical and electrical installation. The chapters
are organized in chronological order in which the IED should be installed.
The operation manual contains instructions on how to operate the IED once it has
been commissioned. The manual provides instructions for monitoring, controlling
and setting the IED. The manual also describes how to identify disturbances and
how to view calculated and measured power grid data to determine the cause of a
fault.
The point list manual describes the outlook and properties of the data points
specific to the IED. The manual should be used in conjunction with the
corresponding communication protocol manual.
The technical manual contains application and functionality descriptions and lists
function blocks, logic diagrams, input and output signals, setting parameters and
technical data sorted per function. The manual can be used as a technical reference
during the engineering phase, installation and commissioning phase, and during
normal service.
1.3.2 Document revision history
Document revision/date Product version History
A/2013-05-07 2.0 First release
Download the latest documents from the ABB Website
http://www.abb.com/substationautomation.
1.3.3 Related documentation
Name of the document Document ID
DNP3 Communication Protocol Manual 1MRS757646
1.4 Symbols and conventions
1.4.1 Symbols
The caution icon indicates important information or warning related
to the concept discussed in the text. It might indicate the presence
Section 1 1MRS757660 A
Introduction
10 RET620
Point List Manual

of a hazard which could result in corruption of software or damage
to equipment or property.
The information icon alerts the reader of important facts and
conditions.
The tip icon indicates advice on, for example, how to design your
project or how to use a certain function.
Although warning hazards are related to personal injury, it is necessary to
understand that under certain operational conditions, operation of damaged
equipment may result in degraded process performance leading to personal injury
or death. Therefore, comply fully with all warning and caution notices.
1.4.2 Document conventions
A particular convention may not be used in this manual.
• Abbreviations and acronyms in this manual are spelled out in the glossary. The
glossary also contains definitions of important terms.
• Push-button navigation in the LHMI menu structure is presented by using the
push-button icons.
To navigate between the options, use and .
• HMI menu paths are presented in bold.
Select Main menu/Settings.
• WHMI menu names are presented in bold.
Click Information in the WHMI menu structure.
• LHMI messages are shown in Courier font.
To save the changes in non-volatile memory, select Yes and press .
• Parameter names are shown in italics.
The function can be enabled and disabled with the Operation setting.
• Parameter values are indicated with quotation marks.
The corresponding parameter values are "On" and "Off".
• IED input/output messages and monitored data names are shown in Courier font.
When the function starts, the START output is set to TRUE.
1MRS757660 A Section 1
Introduction
RET620 11
Point List Manual

1.4.3 Functions, codes and symbols
Table 1: RET620 functions, codes and symbols
Function IEC 61850 IEC 60617 IEC-ANSI
Protection
Three-phase non-directional
overcurrent protection, low stage,
instance 1
PHLPTOC1 3I> (1) 51P-1 (1)
Three-phase non-directional
overcurrent protection, low stage,
instance 2
PHLPTOC2 3I> (2) 51P-1 (2)
Three-phase non-directional
overcurrent protection, high stage,
instance 1
PHHPTOC1 3I>> (1) 51P-2 (1)
Three-phase non-directional
overcurrent protection, high stage,
instance 2
PHHPTOC2 3I>> (2) 51P-2 (2)
Three-phase non-directional
overcurrent protection, instantaneous
stage, instance 1
PHIPTOC1 3I>>> (1) 50P/51P (1)
Three-phase non-directional
overcurrent protection, instantaneous
stage, instance 2
PHIPTOC2 3I>>> (2) 50P/51P (2)
Three-phase directional overcurrent
protection, low stage, instance 1 DPHLPDOC1 3I> -> (1) 67-1 (1)
Three-phase directional overcurrent
protection, high stage, instance 1 DPHHPDOC1 3I>> -> (1) 67-2 (1)
Non-directional earth-fault protection,
low stage, instance 1 EFLPTOC1 Io> (1) 51N-1 (1)
Non-directional earth-fault protection,
low stage, instance 2 EFLPTOC2 Io> (2) 51N-1 (2)
Non-directional earth-fault protection,
high stage, instance 1 EFHPTOC1 Io>> (1) 51N-2 (1)
Non-directional earth-fault protection,
high stage, instance 2 EFHPTOC2 Io>> (2) 51N-2 (2)
Directional earth-fault protection, low
stage, instance 1 DEFLPDEF1 Io> -> (1) 67N-1 (1)
Directional earth-fault protection, low
stage, instance 2 DEFLPDEF2 Io> -> (2) 67N-1 (2)
Directional earth-fault protection,
high stage DEFHPDEF1 Io>> -> (1) 67N-2 (1)
Negative-sequence overcurrent
protection, instance 1 NSPTOC1 I2> (1) 46 (1)
Negative-sequence overcurrent
protection, instance 2 NSPTOC2 I2> (2) 46 (2)
Residual overvoltage protection,
instance 1 ROVPTOV1 Uo> (1) 59G (1)
Residual overvoltage protection,
instance 2 ROVPTOV2 Uo> (2) 59G (2)
Residual overvoltage protection,
instance 3 ROVPTOV3 Uo> (3) 59G (3)
Table continues on next page
Section 1 1MRS757660 A
Introduction
12 RET620
Point List Manual

Function IEC 61850 IEC 60617 IEC-ANSI
Three-phase undervoltage
protection, instance 1 PHPTUV1 3U< (1) 27 (1)
Three-phase undervoltage
protection, instance 2 PHPTUV2 3U< (2) 27 (2)
Three-phase undervoltage
protection, instance 3 PHPTUV3 3U< (3) 27 (3)
Three-phase overvoltage protection,
instance 1 PHPTOV1 3U> (1) 59 (1)
Three-phase overvoltage protection,
instance 2 PHPTOV2 3U> (2) 59 (2)
Three-phase overvoltage protection,
instance 3 PHPTOV3 3U> (3) 59 (3)
Positive-sequence undervoltage
protection, instance 1 PSPTUV1 U1< (1) 47U+ (1)
Positive-sequence undervoltage
protection, instance 2 PSPTUV2 U1< (2) 47U+ (2)
Negative-sequence overvoltage
protection, instance 1 NSPTOV1 U2> (1) 47O- (1)
Negative-sequence overvoltage
protection, instance 2 NSPTOV2 U2> (2) 47O- (2)
Frequency protection, instance 1 FRPFRQ1 f>/f<,df/dt (1) 81 (1)
Frequency protection, instance 2 FRPFRQ2 f>/f<,df/dt (2) 81 (2)
Frequency protection, instance 3 FRPFRQ3 f>/f<,df/dt (3) 81 (3)
Voltage per hertz protection,
instance 1 OEPVPH1 U/f> (1) 24 (1)
Voltage per hertz protection,
instance 2 OEPVPH2 U/f> (2) 24 (2)
Three-phase thermal overload
protection for power transformers,
two time constants
T2PTTR1 3Ith>T (1) 49T (1)
Loss of phase (undercurrent),
instance 1 PHPTUC1 3I< (1) 37F (1)
Loss of phase (undercurrent),
instance 2 PHPTUC2 3I< (2) 37F (2)
Stabilized and instantaneous
differential protection for 2-winding
transformers
TR2PTDF1 3dI>T (1) 87T (1)
Numerical stabilized low impedance
restricted earth-fault protection,
instance 1
LREFPNDF1 dIoLo> (1) 87NL (1)
Numerical stabilized low impedance
restricted earth-fault protection,
instance 2
LREFPNDF2 dIoLo> (2) 87NL (2)
High impedance based restricted
earth-fault protection, instance 1 HREFPDIF1 dIoHi> (1) 87NH (1)
High impedance based restricted
earth-fault protection, instance 2 HREFPDIF2 dIoHi> (2) 87NH (2)
Circuit breaker failure protection,
instance 1 CCBRBRF1 3I>/Io>BF (1) 51BF/51NBF (1)
Table continues on next page
1MRS757660 A Section 1
Introduction
RET620 13
Point List Manual

Function IEC 61850 IEC 60617 IEC-ANSI
Circuit breaker failure protection,
instance 2 CCBRBRF2 3I>/Io>BF (2) 51BF/51NBF (2)
Three-phase inrush detector INRPHAR1 3I2f> (1) 68 (1)
Master trip, instance 1 TRPPTRC1 Master Trip (1) 94/86 (1)
Master trip, instance 2 TRPPTRC2 Master Trip (2) 94/86 (2)
Arc protection, instance 1 ARCSARC1 ARC (1) 50L/50NL (1)
Arc protection, instance 2 ARCSARC2 ARC (2) 50L/50NL (2)
Arc protection, instance 3 ARCSARC3 ARC (3) 50L/50NL (3)
Multipurpose analog protection,
instance 1 MAPGAPC1 MAP (1) MAP (1)
Multipurpose analog protection,
instance 2 MAPGAPC2 MAP (2) MAP (2)
Multipurpose analog protection,
instance 3 MAPGAPC3 MAP (3) MAP (3)
Multipurpose analog protection,
instance 4 MAPGAPC4 MAP (4) MAP (4)
Multipurpose analog protection,
instance 5 MAPGAPC5 MAP (5) MAP (5)
Multipurpose analog protection,
instance 6 MAPGAPC6 MAP (6) MAP (6)
Multipurpose analog protection,
instance 7 MAPGAPC7 MAP (7) MAP (7)
Multipurpose analog protection,
instance 8 MAPGAPC8 MAP (8) MAP (8)
Multipurpose analog protection,
instance 9 MAPGAPC9 MAP (9) MAP (9)
Multipurpose analog protection,
instance 10 MAPGAPC10 MAP (10) MAP (10)
Multipurpose analog protection,
instance 11 MAPGAPC11 MAP (11) MAP (11)
Multipurpose analog protection,
instance 12 MAPGAPC12 MAP (12) MAP (12)
Control
Circuit-breaker control, instance 1 CBXCBR1 I <-> O CB (1) I <-> O CB (1)
Circuit-breaker control, instance 2 CBXCBR2 I <-> O CB (2) I <-> O CB (2)
Disconnector control, instance 1 DCXSWI1 I <-> O DCC (1) I <-> O DCC (1)
Disconnector control, instance 2 DCXSWI2 I <-> O DCC (2) I <-> O DCC (2)
Earthing switch control, instance 1 ESXSWI1 I <-> O ESC (1) I <-> O ESC (1)
Disconnector control, instance 3 DCXSWI3 I <-> O DCC (3) I <-> O DCC (3)
Disconnector control, instance 4 DCXSWI4 I <-> O DCC (4) I <-> O DCC (4)
Earthing switch control, instance 2 ESXSWI2 I <-> O ESC (2) I <-> O ESC (2)
Disconnector position indication,
instance 1 DCSXSWI1 I <-> O DC (1) I <-> O DC (1)
Disconnector position indication,
instance 2 DCSXSWI2 I <-> O DC (2) I <-> O DC (2)
Table continues on next page
Section 1 1MRS757660 A
Introduction
14 RET620
Point List Manual