Abocom ISM560 User manual

M73-APO02-460
Internal
Fax Modem 56K
Quick Installation Guide

FCC Part 68 Registration
This device complies with FCC Part 68 rules, and the use
of this device is subject to the following restrictions:
1. The FCC has established rules which permit this device to
be directly connected to the telephone network.
Standardized jacks are used for these connections. This
equipment should not be used on party lines or coin
phones.
2. If this device is malfunctioning, it may also be causing
harm to the telephone network; this device should be
disconnected until the source of the problem can be
determined and until repair has been made. If this is not
done, the telephone company may temporarily
disconnect service.
3. The telephone company may make changes in it's facilities,
equipment, operation and procedures; if such changes
affect the compatibility or use of this device, the
telephone company is required to give adequate notice
of the situation with the FCC.
4. If the telephone company requests information on what
equipment is connected to their lines, inform them of:
a. The telephone number to which this unit is connected.
b. The Ringer Equivalence Number (REN).
c. The USOC jack required.
d. The FCC Registration number.
Items (b) and (d) are indicated on the label. The Ringer
Equivalence Number (REN) is used to determine how many
devices can be connected to your telephone line. In most
areas, the sum of the REN's of all the devices on any one line
should not exceed 5.0. If too many devices are attached, they
may not ring properly.
FCC Part 15 Registration
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interface, and
2. This device must accept any interface received including
interface that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the distance between the equipment and
receiver
 Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
 Consult an experienced radio/TV technician for help.
CTR 21 pan-European Certification
This equipment has been approved in accordance with
Council Decision 98/482/EC for pan-European single
terminal connection to the public switched telephone network
(PSTN). However, due to differences between the individual
PSTNs provided in different countries, the approval does not,
of itself, give an unconditional assurance of successful
operation on every PSTN network termination point. In the
event of problems, you should contact your equipment
supplier in the first instance.
This device is designed to work with the notified networks in
all EC member states. Nevertheless, some of the network
services in invidual countries might not be supported, but
they will not affect the normal data and fax applications. For
example, the metering charge service in Germany. Besides
you may encounter difficulty of using PULSE dialing
function in some of the countries, such as Nordic countries.
This kind of network compatibility is dependent on the
physical and software settings of this device. If the users
are desired to use this device on those networks, they should
contact the vendor or supplier first.

HARDWARE INSTALLATION
Precautions:
Please be sure you take adequate anti-static
precautions when handling this product. The
simplest way to achieve this is; touch a
non-painted surface of the computer’s chassis
during the hardware installation.
1. Make sure the computer is turned off before
installing the device.
2. Remove the expansion slot cover from the
computer.
3. Carefully slide the PCI modem card into an
available PCI slot, applying even pressure to
the card. Secure the card to the computer
with the screw. (PCI slots are 85mm long and
positioned 40mm from the PC’s rear panel.
Generally there are several PCI slots side by
side).
4. Plug one end of the telephone cable into the
Modem line jack and another end into the
telephone jack in wall.
5. Replace the cover.
6. You are now ready to continue the software
installation.
- 1 -

- 2 -
SOFTWARE INSTALLATION
Windows 98 Installation
1. Reboot the computer system after the modem
is well inserted into the PCI slot of your
computer. Windows 98 will automatically
detect the device. Click Next to continue.
2. Insert the device driver compact disc into
your CD-ROM drive when the following
dialog box appears. Click Next to continue.

- 3 -
3. Select Specify a location and press Browse
to choose the Dirver\Win98 folder in your
CD-ROM drive. Then click Next.
4. Click Next to continue.
5. When the following figure appears, click
Finish to complete software installation.

Windows 2000 Installation
1. Reboot the computer system after the
modem is well inserted into the PCI slot of
your computer. Windows 2000 will
automatically detect the new hardware
device and prompt the following message.
Click Next to continue
2. Select Search for a suitable driver for my
device (recommended) and click Next.
3. Select Specify a location and click Next.
4. Insert the device driver compact disc into
your CD-ROM drive. Click Browse to
the location where the driver is stored
(Driver\Win2000) and click OK.
- 4 -

- 5 -
5. Click Next. Windows 2000 will start
copying necessary files onto your system.
6. Click Yes to continue.
7. Click Finish to complete the software
installation.
Windows ME Installation
1. Reboot the computer system after the
modem is well inserted into the PCI slot of
your computer. Windows ME will
automatically detect the hardware device

- 6 -
and prompt the following message. Select
Specify the location of the driver
(Advanced) and click Next.
2. Insert the device driver compact disc you’re
your CD-ROM drive. Select Specify a
location and click browse to the location
where the driver is stored (Driver\Winme).
And then click Next.
3. Click Next to continue.

- 7 -
4. Click Finish when the following screen
prompts. The installation program will
continue.
5. Repeat the step 1as described above.
6. Follow the on-screen instruction to
continue.
7. Click Next to continue.

- 8 -
8. Press Finish to complete the software
installation.
9. Go to StartSettingsControl Panel
SystemsDevice Manager. Click Modem
and WDM Modem Enumerator to expand.
If Agere System Soft Modem is listed as
below, the software installation will truly be
completed. If not, please consult your
distributor for the technical support.

- 9 -
Windows XP Installation
1. Reboot the computer system after the
modem is well inserted into the PCI slot of
your computer. Windows XP will
automatically detect the new hardware
device and prompt the following message.
Select Install from a list or specific
location and click Next.
2. Insert the device driver compact disc into
your CD-ROM drive. Select Include this
location in the search and click Browse to
direct Windows XP to the location where
the driver stored (\Driver\xp). Then click
Next.

- 10 -
3. When the following window appears, click
Continue Anyway.
4. Please wait a while for windows to copy a
number of files onto your PC.
5. Click finish to complete the software
installation.

- 11 -
Windows NT Installation
1. Reboot the computer system after the modem
is well inserted into your PCI slot of your
computer.
2. Load the device driver compact disk in your
CD-ROM drive.
3. Start Windows NT.
4. Go to My Computer.
5. Click the CD-ROM drive. Click the
driver\Winnt4 folder. Or you may click the
Browse button to select the CD-ROM drive
and the driver\Winnt4 folder.
6. Double-click Setup.exe. The installation
program will proceed automatically.

CHECKING COUNTRY/REGION
Perform the following steps to check the
country/region settings for the modem before
using the Internal Fax Modem 56K. For the best
performance, make sure the country/region is
selected to the country where you are using the
device, e.g., United States of America.
Windows 98/ 98SE/ 2000/ Millennium
1. Go to
Start→Settings→Control Panel→Modems.
2. Specify the country/region where you are
when the Location Information dialog box
appears. And then click Close.
Windows XP
1. Go to Start→Control Panel→Phone and
Modem Options.
2. In the Dialing Rules tab, click edit to
configure.
- 12 -
3. In the General tab, specify the
country/region where you are. Click OK to
enable your settings.

- 13 -
UNINSTALL
If you want to uninstall the driver of the Internal
Fax Modem 56K after installation, perform the
following steps.
1. Go to My Computer.
2. Select the CD-ROM drive which contains the
Internal FaxModem 56K device driver.
3. Choose and double-click the Win98, WinME
or Winnt4, Win2000, XP folder depending
on the system you are working on.
4. Click
Agrsmdel.exe. The Internal Fax Modem
56K device driver will automatically
removed.
Windows NT4.0
1. Go to

- 14 -
Start→Settings→Control Panel→Modems.
2. When the Modems Properties dialog box
appears, click the Dialing Properties button.
3. When the Dialing Properties dialog box
appears, specify the country/region that you
are in and click OK.
UNINSTALL
If you want to uninstall the driver of the Internal
Fax Modem 56K after installation, perform the
following steps.
1. Go to My Computer.
2. Select the CD-ROM drive which contains the
Internal FaxModem 56K device driver.
3. Choose and double-click the Win98,
Win2000, WinME or Winnt4 folder
depending on the system you are working on.
4. Click
Agrsmdel.exe. The Internal Fax Modem
56K device driver will automatically
removed.
APPLICATIONS
To manage the Internal Fax Modem 56K for data
communication, e.g., faxes sending/receiving or
the Internet navigation, you can use any
application programs you are familiar with. See
the examples as described below.
Internet Access
1. Go to My Computer.
2. Select Dial-Up Networking.
3. Double-click Make a New Connection. A
dialogue box will appear and allow you to
name the new connection and select the

- 15 -
device. Name the new connection
appropriately and click Next.
4. Enter the area code and phone number
provided by your Internet Service Provider
(ISP). Follow the on-screen instruction to
proceed.
5. When finished, from the Dial-Up
Networking window, right-click your newly
built connection. Select Properties. On
the Server Types tab, enter the proper
selections as shown below and click OK to
finish the settings.

- 16 -
.
You are now ready to connect to the Internet.