Abocom UTA128 User manual

USB ISDN TA
Quick Installation Guide
Doc No.: 120501-03

Table of Contents
INTRODUCTION................................................ 1
THE USB ISDN TA ............................................ 1
SYSTEM REQUIREMENTS..................................... 1
PACKAGE CONTENTS .......................................... 1
GETTING TO KNOW THE USB ISDN TA ..... 2
THE ADAPTER’S PORTS....................................... 2
THE ADAPTER’S LEDS....................................... 2
INSTALLING THE USB ISDN TA .................... 3
INSTALLING THE USB ISDN TA & CABLING ..... 3
CONNECTING TO AN ISDN NETWORK ................ 3
WINDOWS 98 INSTALLATION ....................... 4
DIAL UP TO INTERNET ........................................ 5
WINDOWS 2000 INSTALLATION ................... 7
DIAL UP TO INTERNET ........................................ 8
WINDOWS ME INSTALLATION................... 10
DIAL UP TO INTERNET ...................................... 11
WINDOWS XP INSTALLATION.................... 13
DIAL UP TO INTERNET ...................................... 14
APPENDIX......................................................... 15
SPECIFICATIONS ................................................ 15

Introduction
The USB ISDN TA
ISDN (Integrated Service Digital Network) is the
most convenient and economical way to use the
existing copper wire for both voice and data
communication.
With the USB ISDN TA, data transmission rate can
reach up to 128K. It can not only provides 128K
transmission but also allows voice conversation and
fast Internet Access simultaneously.
The USB ISDN TA is a low cost USB ISDN
modem for applications like INTERNET ACCES
and FAX capabilities. EASY access due to plug and
play features via USB bus and low cost due to host
processing concept and remote powering via USB
bus features.
System Requirements
 An USB port
 A CD-ROM drive
 Microsoft Windows 98/2000/ME/XP
Package Contents
 One USB ISDN TA
 One Standard USB Cable
 One ISDN Cable
 One Compact Disc
- 1 -

Getting to Know the USB
ISDN TA
The Adapter’s Ports
 ISDN Port: connects to an ISDN cable
 USB Port: connects to an USB cable
The Adapter’s LEDs
 Power: glows green when the software driver
is well installed in your computer
 B1: glows green when transmitting / receiving
data in 64 Kbps speed mode
 B2: glows green when transmitting / receiving
data in 128 Kbps speed mode
- 2 -

Installing the USB ISDN TA
Installing the USB ISDN TA & Cabling
1. Insert the USB cable’s square end into the
adapter’s USB port.
2. Insert the rectangular end of the USB cable
into the USB host port on your PC.
Connecting to an ISDN Network
1. Connect one end of an ISDN cable into the
adapter’s ISDN port.
2. Connect the other end of the ISDN cable into
S/T port on NT1 ISDN device.
- 3 -

Windows 98 Installation
1. Connect the rectangular end of the USB cable
into the USB host port of your computer, and
the square end into the USB port of your
network adapter. Windows 98 will
automatically detect the device. Click Next
to continue.
2. Select Search for the best driver for your
device (Recommended) and click Next.
3. Insert the device driver into your CD-ROM
drive. Select Specify a location, direct
Windows 98 to the location where the driver
stored and click Next. Windows 98 will
search for the suitable driver for the software
installation need.
4. Click Next. Windows 98 will start copying
necessary files onto your system.
5. Click Next.
6. Select the switch protocol that your telephone
company uses and click Next.
7. Enter the telephone numbers that your ISP
provided and click Next.
8. Click Finish.
9. When asked to supply the original Windows
98 CD-ROM, you need to insert it into your
compact disc drive. Click OK.
10. Click Finish to complete the software
installation.
11. To verify if your network adapter exists in
your computer and well enabled, you can
perform the following steps.
- 4 -

12. Go to Start, Settings, Control Panel,
Systems and then Device Manager.
13. Click Intelligent ISDN Drivers and Network
adapters to expand. If Intelligent CAPI 2.0
driver, Intelligent USB adapter and
Intelligent ISDN WAN miniport are found,
that means your network adapter exists and
enabled. If not, consult your distributor for
technical support.
Dial Up to Internet
1. Go to My Computer, Dial-Up Networking.
Double-click the Make New Connection
icon.
- 5 -

2. Name your connection appropriately, select
your network adapter and click Next.
3. Enter the Telephone number that your ISP
provided and click Next.
4. Click Finish to complete the connection setup.
5. When the My Connection icon appears,
right-click the icon and select Properties.
6. Click to clear the Use area code…check box,
make appropriate settings as the following
figure and click OK.
7. Enter the User name and Password that your
ISP provided and click Connect, then you will
be able to surf the Internet.
- 6 -

Windows 2000 Installation
1. Connect the rectangular end of the USB cable
into the USB host port of your computer, and
the square end into the USB port of your
network adapter. Windows 2000 will
automatically detect the device. Click Next
to continue.
2. Select Search for a suitable driver for my
device (recommended) and click Next.
3. Select Specify a location and click Next.
4. Insert the device driver into your CD-ROM
drive. Click Browse, direct Windows 2000
to the location where the driver stored and
click OK.
5. Click Next. Windows 2000 will start
copying necessary files onto your system.
6. Click Finish to complete the software
installation.
7. To verify if your network adapter exists in
your computer and well enabled, you can
perform the following steps.
8. Go to Start, Settings, Control Panel,
Hardware and then Device Manager.
9. Click Intelligent ISDN Drivers and Network
adapters to expand. If Intelligent CAPI 2.0
driver, Intelligent USB adapter and
Intelligent ISDN WAN miniport are found,
that means your network adapter exists and
enabled. If not, consult your distributor for
technical support.
- 7 -

Dial Up to Internet
1. Go to Start, Settings, Control Panel,
Network and Dial-up Connections.
Double-click the Make New Connection icon.
When the following figure appears, click Next
to continue.
2. Select Dial-up to the Internet and click Next.
3. Select I want to set up…and click Next.
4. Select I connect through a phone line and a
modem and click Next.
5. Select your network adapter and click Next.
6. Click to clear the Use area code…check box,
enter the Telephone number that your ISP
provided and click Next.
7. Enter the User name and Password that your
ISP provided and click Next.
8. Click Next.
- 8 -