Abocom SW1600B User manual

M73-APO07-310
16-Port Fast Ethernet Switch
User’s Guide

FCC REGULATORY STATEMENTS
Part15, Class B
This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interface, and
2. This device must accept any interface received, including interface that may cause
undesired operation. This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Changes or modifications not expressly approved by party responsible for compliance
could void the user authority to operate the equipment.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.

- 1 -
INTRODUCTION
The 16-Port Fast Ethernet 10/100Mbps N-Way Switch provides you a flexible, reliable, and
affordable solution of the Ethernet network. It comes with sixteen 10BASE-T /100BASE-TX
ports. The 16-Port Fast Ethernet 10/100Mbps N-Way Switch is able to operate in both half
and full-duplex modes. Each port delivers up to 200Mbps throughput in full duplex mode.
The 16-Port Fast Ethernet 10/100Mbps N-Way Switch also processes a N-Way auto-
negotiation function, which automatically adjusts the device for optimum operation; “Store-
and-Forward” architecture filters to eliminate error packets and improve efficiency. Plus, the
auto-MDI/MDIX technology provides the convenience of using a straight through or a
crossover Ethernet cable and you will be connected with any other devices. Moreover, the
built-in Universal Power Supply allows you to install the switch easily without the external
power adapter.
Key Features
 Complies with IEEE 802.3 10Base-T and IEEE 802.3u 100Base-TX standards
 “Store and Forward” architecture filters
 IEEE 802.3x or Back Pressure (HDX) Flow Control
 16 x RJ45 STP/UTP Ethernet ports on front panel
 4K MAC Address table supported
 10/100Mbps auto-detection on Full or Half Duplex
 Each Ethernet port supports Auto-MDI/MDIX (auto-crossover) technology
 Provides non-blocking and Head-of-line blocking forwarding prevention
 256KB on-chip buffer
 Built in Universal Power Supply: 90~264V
 Emission certification: FCC Class B, CE mark

PARTS NAMES AND FUNCTIONS
Front Panel: LED Indicators
Status
LED Color
Solid Flashing
Power Green Power is on. N/A
LINK/ACT Green Connection is detected Sending or Receiving
packets
Speed Green ON for 100Mbps, OFF for 10Mbps N/A
Rear Panel: Power Port
- 2 -

- 3 -
HARDWARE INSTALLATION
The switch is considered as a “plug and play” network device and requires no special setup
procedures. Connect the power cord and cables correctly and you are ready to go.
Switch installation
1. Put the switch on the appropriate location. When you install the switch, there are two
things needed to be considered:
 Location: Your switch should be located in a place that is central to your
home/office space and allows all computers and networked devices connected to
your switch.
 Power: Remember to locate your switch near electrical outlet.
2. Power on the switch by connecting the power cord.
3. Verify if the power (POWER) LED is on. If the POWER LED does not light up,
check the power cord and power outlet to verify its connection. If it still remains unlit,
please contact your dealer for support.
Ethernet Port Connection
Connect user machines, servers, another switch, hub, or any other devices to the Ethernet
ports on this switch with either straight through or crossover Ethernet cables.

- 4 -
SPECIFICATION
Standards
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE802.3x Flow Control
Protocol CSMA/CD
Ports Sixteen 10/100Mbps RJ-45 ports support auto-MDI/MDIX
Switching Scheme Store-and-Forward
Flow control Full Duplex: IEEE802.3x
Half Duplex: Back Pressure
Cabling type UTP Category 3 or better (10Base-T)
UTP Category 5 or better (100Base-TX)
Speed per port 10Mbps or 100Mbps (Half Duplex)
20Mbps or 200Mbps (Full Duplex)
MAC Address 4K
Power Green Power is up.
LINK/ACT Green:
On for connection detected;
Flashing for sending/
receiving data
LED indicators
SPD Green On for 100Mbps, off for
10Mbps
Physical Dimension 273 x 161 x 45 ( mm) (Width x Depth x Height)
Weight 1.2 Kg
Input power specifications AC 90~264V
Power Consumption 13W
Agency and Regulatory FCC Class B, CE mark
Operating Temperature 0°C to 40°C
Operating Humidity 5~90% non-condensing