ABSCO SHEDS 23232GK User manual

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23232GK
2.26mW x 2.26mD x 2.10mH
Model: 23232GK 1.20 1
17/06/19
Download the Absco
Sheds Assembly App
for instructional videos
MANU FACTURED
IN AUSTRALIA
SNAPTiTE
Assembly
AU: 1800 029 701
NZ: 0800 466 444
[email protected]
www.abscosheds.com.au
CONCRETESLAB
2360mm (7’9”)
2360mm (7’9”)
When laying concrete slab, ensure there
is a rebated edge 25mm deep around
the perimeter. This will help water egress
from the base of the shed.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: 23151GK 21-11-2017
CONCRETE SLAB
2360mm
1620mm
FRONT: 2.26m
SIDE: 1.52m
HEIGHT: 1.95m
We thank you for choosing an Australian made
shed. For further assistance please visit our detailed
instructional video library at
Http://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be
number ONE, so please let us know what you think
of our instructions. Feedback makes us better.
[email protected]
CONCRETE
REBATED EDGE
BOTTOM CHANNEL
CONCRETE SLAB
75mm WIDE REBATE
100mm
WHEN LAYING YOUR CONCRETE
SLAB, ENSURE THERE IS A
REBATED EDGE 25mm DEEP
AROUND THE PERIMETER
THIS WILL HELP WATER EGRESS
FROM THE BASE OF THE SHED
Absco Industries
Premier Shed Model: 23151GK
PAGE 01
For construction in non-cyclonic areas
Wind rating: N2 as per AS4055-2012.
If you require a higher wind rating please contact
us: [email protected] or 1800 029 701
NOTE: This shed can be upgraded to wind
rating: C1 as per AS4055-2012 with the additional
purchase of a Cyclone Kit.
日本改定日2021/4/30

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23232GK
2.26mW x 2.26mD x 2.10mH
Model: 23232GK 1.20 2
17/06/19
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough
understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described
and illustrated on "COMPONENTS PACKING LIST" pages.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately
illustrated on “FINAL CONSTRUCTION” page.
TOOLS REQUIRED
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and
safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored to a solid foundation immediately after construction is
completed.
• It is highly recommended to erect the shed with two or more people.
RECOMMENDED
3mm drill bit 10mm drill bits metal & masonry

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23232GK
2.26mW x 2.26mD x 2.10mH
Model: 23232GK 1.20 3
17/06/19
COMPONENT PACKING LIST
Check off all components.
QTY
MAIN PACK CARTON (1 OF 1)
DESCRIPTION PART # HKDESCRIPTION PART #
2 2
SNAPTiTE SHEET
STRAIGHT
1785x773mm
SNAPTiTE SHEET
STRAIGHT
1785x773mm
SNAPTiTE SHEET
STRAIGHT
1725x773mm
SNAPTiTE SHEET
STRAIGHT
1725x773mm
SNAPTiTE SHEET
STRAIGHT
1170x773mm
SNAPTiTE SHEET
LEFT ANGLE
1915x773mm
SNAPTiTE SHEET
RIGHT ANGLE
1915x773mm
SNAPTiTE SHEET
PEAK
1980x773mm
SNAPTiTE SHEET
S
PERFORATED PAIR
1785x329mm
2
2
1
1
1
1
1
6
RIDGE BEAM
1152mm LONG
SPLICED
PEAK BRACE
450mm
LONG 22
RIDGE BEAM
JOINER
450mm LONG
11 23232G
CHANNEL PACK 23232GCP
123232G INSTRUCTIONS & FITTINGS PACK INSTP##23232G
30A 36R
31A 36L
DOORA 42D
DOORB
49A
ZACO15A RB97BL/R
ZARSP
39B

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23232GK
2.26mW x 2.26mD x 2.10mH
Model: 23232GK 1.20 4
17/06/19
COMPONENT PACKING LIST
23232GCP CHANNEL PACK
QTY QTY
DESCRIPTION PART # CHK CHKDESCRIPTION PART #
CHANNEL
1126.5mm
NOTCHED
ONE END
CHANNEL
1126.5mm
NOTCHED
ONE END
CHANNEL
NOTCHED
ONE END
CHANNEL
NOTCHED
ONE END
CHANNEL
NOTCHED
ONE END
CHANNEL
NOTCHED
ONE END
CHANNEL
1126.5mm
NOTCHED
ONE END
CHANNEL
1126.5mm
NOTCHED
ONE END
CHANNEL
1126.5mm
STRAIGHT
CHANNEL
1126.5mm
STRAIGHT
CHANNEL
1126.5mm
NOTCHED
ONE END
CHANNEL
1126.5mm
NOTCHED
ONE END
CHANNEL
1725mm
STRAIGHT - HINGES
CHANNEL
773mm
STRAIGHT
CHANNEL
1143mm
STRAIGHT
CHANNEL
1143mm
STRAIGHT
CHANNEL
STRAIGHT
JAMB
1785mm
NOTCHED
BOTH ENDS
JAMB
1725mm
STRAIGHT
JAMB
NOTCHED
BOTH ENDS
JAMB
1120mm
STRAIGHT
11
11
1
1
2
22
2
4
4
1
STRAIGHT
CHANNEL
1
44
1
1
1 1
2 2
Check off all components.
79E 58B
1568mm 1725mm
1568mm
1120mm1120mm
1120mm1120mm
89A
83L
58A 58C
81DL
54LL
81CL
54KL
81DR
54LR
81CR
54KR
83R
89C 90F
91A
60BL
54BL
60BR
54BR
LIP
1170mm
486A

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23232GK
2.26mW x 2.26mD x 2.10mH
Model: 23232GK 1.20 5
17/06/19
COMPONENT PACKING LIST
PSTKDBL - DOUBLE DOOR FITTINGS PACK
3PADBOLT
115mm LONG FAST006 2PADBOLT HASP FAST007
13mm
DRILL BIT DRILL
1SCREW
PACK 12 PACK12P
1PHILLIPS HEAD
DRIVER BIT
S2 PH2
FAST038
18G x 3/8 SELF
TAPPING SCREWS
x 220
PACK220
PACK12P - SCREW PACK 12
12 SBS43E
POP RIVET FAST009 12 3/16" x 1/2"
COUNTERSUN K
SCREW & NUT
FAST004
FAST005
83/16 x 1/2
PAN HEAD SCREW FAST002 83/16 NYLOCK NUT FAST003
Check off all components.
INSTRUCTIONS & FITTINGS PACK
CHANNEL
JOINER
200mm LONG
ZACSJ
DOOR PLATE
165mm CO12A
WAFER TEK SCREW
CL3 10-16x16mm FAST014
1010
2GABLE CA P
170mm CO14A
2
1DOUBLE DOOR
FITTINGS PACK PTSKDBL IM
1INSTRUCTION MANUAL

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23232GK
2.26mW x 2.26mD x 2.10mH
Model: 23232GK 1.20 6
17/06/19
Guide on Splitting Sheets
• This product comes with a perforated sheet that is designed to be split into two smaller sheets.
• These sheets have sharp edges. Once separated please use appropriate foot and hand
protection when handling.
• In order to split the sheet lay it on the ground and lift and fold one end until the perforations have
cleanly snapped.
• Discard the middle piece as scrap when convenient. Fold the scrap piece in half two or three
times and throw in garbage.
Check sheet for
perforations
Fold first side of
sheet until free
Fold middle section
of sheet until free
Discard middle piece
SCRAP
SCRAP
SCRAP
SCR AP
SCRAP
SCRAP
SCRAP
SCRAP
SPLITTING SHEET 39B
COMPONENT
DESCRIPTION
PART
No.
COMPONENT
DESCRIPTION
PART
No.
QTY QTY
1STEEL SHEET
1785mm X 773mm 2STEEL SHEET
1785mm X 329mm 39B
=
39B

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23232GK
2.26mW x 2.26mD x 2.10mH
Model: 23232GK 1.20 7
17/06/19
SNAPTiTE ASSEMBLY GUIDE
The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for
tools and fasteners.
To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.
Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet.
Each perimeter channel must finish flush with the edges of the sheets. Simply tap the channel along
the sheets until each end is neatly flush. If you need to remove channels from the panels, slide it off
from the side.
Channel locks the shed panel into
position without the need for screws!
FASTENING SYMBOLS
Secure channel to sheeting by SNAPTiTE
fastening method.
Join components together with one
screw at this location only, as some
channels have extra holes that are not
required for this model of shed.
Do not join components together at
this location yet, as the screws may
obstruct further assembly of the other
components.
Join components together by pre-drill-
ing the holes first. Use one component as
template to mark where the holes are and
drill with a 3mm drill bit.
3mm pop rivet
4mm nut and bolt set.
D
SNAP
T TE
i

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23232GK
2.26mW x 2.26mD x 2.10mH
Model: 23232GK 1.20 8
17/06/19
Guide on Joining Spliced Channels
The text marked on all parts must be shown on the same side as each other
Step 1.
Position the channels and the
CSJ joiner so the centre of
the CSJ is in line with the end
of each channel to be joiner
together.
Step 2.
Join the first channel to the CSJ
by inserting the centre of the
CSJ, on an angle, to the end of
the channel where the JOIN>>
text is marked.
Push down one side of the CSJ
until you hear a ‘click’.
Step 3.
Join the second channel to the
CSJ by positioning the <<JOIN
of the channel at the centre of
the CSJ, on an angle. Push the
CSJ into the channel until you
hear a ‘click’.
Finished Channel.
The joined channels should
now look like the picture with
the CSJ positioned equally
inside of the joined channels.
Drill out holes with 3mm drill
bit in CSJ to match the holes
in channel and secure with the
screws supplied.
These may have to be
temporarily removed during
assembly.
= =
JOIN>> <<JOIN
CSJ
==
JOIN>>
J
==
JOIN>> SJ
= =
JOIN>>
<<JOIN
= =
JOIN>> <<JOIN
Finished Spliced
Channel
Channel
Push
20mm 15mm
CSJ
.
...

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23232GK
2.26mW x 2.26mD x 2.10mH
Model: 23232GK 1.20 9
17/06/19
PRE-ASSEMBLY OF SPLICED CHANNELS
NOTE: Some channels may have holes in them - You will
need to redrill holes where CSJ joining channel covers
them.
Join together 20 x channel sections using 10 x channel joiners (Part CSJ)
=
=
=
=
=
4 X 81CR
2253mm
2 x 60B
4 x 81C
1 x 54B
81CL
81CR
60BR
60BL
2 X 60BR
2 X 60BL
4 X 81CL
1 X 54BR
1 X 54BL
54BR
54BL
=
81DR
81DL
1 x 81D
1 X 81DR
1 X 81DL
1 X 54LR
1 X 54LL
1 X 54KR
1 X 54KL
54LR 54LL
54KR 54KL
1 x 54K
1 x 54L

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23232GK
2.26mW x 2.26mD x 2.10mH
Model: 23232GK 1.20 10
17/06/19
Tek screw driver bit
Push
Guide on Joining a Spliced Ridge Beam
Follow these three steps to assemble a ridge beam.
Step 1.
Place two ridge beams as
shown and push them together.
Slide the cap of one under the
other.
NOTE.
There is a 50mm overlap of the
ridge caps when the beams are
in position.
Step 2.
Use the ZARSP to connect at
the centre of the two ridge
beams. Be sure it is pushed in
fully.
Step 3.
Turn over the ridge beam.
Measure 250mm from the
middle along the centre of one
ridge beam, mark spacings of
50mm. Fasten with a Tek screw
at each marking.
Repeat to the other side of the
ridge beam assembly.
TIP: Predrilling each hole with
the 3mm drill bit makes it easier
to fasten.
50mm
225mm
ZARSP
Finished Spliced Ridge Beam
Finished
Spliced Ridge Beam
ZARSP
Ridge Beam
Self drilling Tek screw