ABSCO SHEDS 30232GK User manual

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30232GK
3.00mW x 2.26mD x 2.00mH
Model: 30232GK 1.22 1 28/04/2022
DOWNLOAD
OUR APP FOR
ASSEMBLY
VIDEOS
PLEASE LEAVE A REVIEW
Tell us about your experience!
Visit www.abscosheds.com.au/review
AU: 1800 029 701
N Z: 0800 466 444
[email protected]
www.abscosheds.com.au
CONCRETE SLAB
3100mm (10.17'')
2360mm (7.7")
When laying concrete slab, ensure there
is a rebated edge 25mm deep around
the perimeter. This will help water egress
from the base of the shed.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: 23151GK 21-11-2017
CONCRETE SLAB
2360mm
1620mm
FRONT: 2.26m
SIDE: 1.52m
HEIGHT: 1.95m
We thank you for choosing an Australian made
shed. For further assistance please visit our detailed
instructional video library at
Http://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be
number ONE, so please let us know what you think
of our instructions. Feedback makes us better.
[email protected]
CONCRETE
REBATED EDGE
BOTTOM CHANNEL
CONCRETE SLAB
75mm WIDE REBATE
100mm
WHEN LAYING YOUR CONCRETE
SLAB, ENSURE THERE IS A
REBATED EDGE 25mm DEEP
AROUND THE PERIMETER
THIS WILL HELP WATER EGRESS
FROM THE BASE OF THE SHED
Absco Industries
Premier Shed Model: 23151GK
PAGE 01
For construction in non-cyclonic areas
Wind rating: N2 as per AS4055-2021.
If you require a higher wind rating please contact
us: [email protected] or 1800 029 701
NOTE: This shed can be upgraded to wind
rating: C1 as per AS4055-2021 with the additional
purchase of a Cyclone Kit.

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30232GK
3.00mW x 2.26mD x 2.00mH
Model: 30232GK 1.22 2 28/04/2022
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough
understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described
and illustrated on "COMPONENTS PACKING LIST" pages.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately
illustrated on “FINAL CONSTRUCTION” page.
TOOLS REQUIRED
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and
safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored to a solid foundation immediately after construction is
completed.
• It is highly recommended to erect the shed with two or more people.
• Do not sit, stand or walk on the roof of your shed.
RECOMMENDED
5/16” Hex driver bit
Ladder Hammer drill Shifter
10mm metal drill bit
10mm masonry drill bit
Pop riveterCordless drill

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30232GK
3.00mW x 2.26mD x 2.00mH
Model: 30232GK 1.22 3 28/04/2022
COMPONENT PACKING LIST
Check off all components.
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY
STEEL SHEET
1785mm X 773mm
(70.3" X 30.4")
STEEL SHEET
1785mm X 773mm
(70.3" X 30.4")
STEEL SHEET
1725mm X 773mm
(67.9" X 30.4")
STEEL SHEET
1725mm X 773mm
(67.9" X 30.4")
STEEL SHEET
1170mm X 773mm
(40.1" X 30.4")
STEEL SHEET
STEEL SHEET
STEEL SHEET
1980mm X 773mm
(77.9" X 30.4")
STEEL SHEET
1785mm X 711mm
(70.3" X 28.0")
30A
31A
A
B
49A
36L
36R
42D
34A
QTY
15A
2
2
2
1
1
8
2
2
2
2
PEAK BRACE
490mm (19.3")
97AL
1
ZARSP
RIDGE
BEAM
1
1
L = 1521mm (59.9")
RIDGE BEAM JOINER
L: 450mm (17.7")
97AR
RIDGE
BEAM
L = 1521mm (59.9")
1852mm TO MIDPOINT
X 773mm
MIDPOINT
1852mm TO MIDPOINT
X 773mm
MIDPOINT
Nominal sheet widths are shown. +/- 2mm is within tolerance.

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30232GK
3.00mW x 2.26mD x 2.00mH
Model: 30232GK 1.22 4 28/04/2022
COMPONENT PACKING LIST
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY
55AL
55CL
55BL
81BL
81AL
81CL
60AL
QTY
55CR
1
1
1
1
2
2
2
1
1
1
1
2
2
2
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1496.5mm (58.9")
55BR
81BR
81AR
81CR
60AR
55AR
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
CHANNEL
L = 1496.5mm (58.9")
79A
1CHANNEL
L = 1568mm (61.7")
83L
2CHANNEL
L = 1143mm (45.0")
58A
283R 2CHANNEL
L = 1143mm (45.0")
58B
1CHANNEL
L = 1725mm (67.9")
58C
4CHANNEL
L = 773mm (30.4")
CHANNEL WITH HINGES
L = 1725mm (67.9")
CHANNEL
L = 1126.5 (44.3")

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30232GK
3.00mW x 2.26mD x 2.00mH
Model: 30232GK 1.22 5 28/04/2022
COMPONENT PACKING LIST
89A
90A
89C
91A
86A
JAMB L= 1785mm (70.3")
JAMB L= 1568mm (61.7")
JAMB L= 1725mm (67.9")
JAMB L= 1120mm (44.1")
LIP TRIM
1170mm (46.1")
2
1
1
4
4
CSJ
10 CHANNEL JOINER
L= 200mm (7.9")
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY QTY
14A
2
12A
2
CAP GABLE
L: 170mm
(6.7")
DOOR
STRAP
L: 165mm
(6.5")
DOOR
PADBOLT
HASP
2
3
SELF TAPPING SCREWS
PACKET CONTAINING 220
1
DOOR
PADBOLT
3/16 COUNTERSUNK
SCREWS & NUTS
12
3/16 ROUND HEAD
BOLTS & NYLOCK NUTS
83.2 x 8mm
BLIND POP RIVETS
12
PSTKDBL - DOUBLE DOOR FITTINGS PACK
PACK12P - SCREW PACK 12
PACK12P
SCREW PACK 12
1
PHILLIPS DRIVER BIT
3mm DRILL BIT DRILL FAST038
FAST007FAST006
INSTRUCTIONS & FITTINGS PACKET
ASSEMBLY INSTRUCTION
MANUAL
1
10
1 1
1
1
SELF TAPPING SCREWS
PACKET CONTAINING 100
PSTKDBL
DOUBLE DOOR FITTINGS PACK
HEX HD
TEK SCREW W/ NEO
WASHER 10-16x16mm
FAST033

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30232GK
3.00mW x 2.26mD x 2.00mH
Model: 30232GK 1.22 6 28/04/2022
SNAPTiTE ASSEMBLY GUIDE
The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for
tools and fasteners.
To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.
Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet.
Each perimeter channel must finish flush with the edges of the sheets. Simply tap the channel along
the sheets until each end is neatly flush. If you need to remove channels from the panels, slide it off
from the side.
Channel locks the shed panel into
position without the need for screws!
FASTENING SYMBOLS
Secure channel to sheeting by SNAPTiTE
fastening method.
Join components together with one
screw at this location only, as some
channels have extra holes that are not
required for this model of shed.
Do not join components together at
this location yet, as the screws may
obstruct further assembly of the other
components.
Join components together by pre-drill-
ing the holes first. Use one component as
template to mark where the holes are and
drill with a 3mm drill bit.
3mm pop rivet
4mm nut and bolt set.
D
SNAP
T TE
i

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30232GK
3.00mW x 2.26mD x 2.00mH
Model: 30232GK 1.22 7 28/04/2022
Guide on Joining Spliced Channels
The text marked on all parts must be shown on the same side as each other
Step 1.
Position the channels and the
CSJ joiner so the centre of
the CSJ is in line with the end
of each channel to be joiner
together.
Step 2.
Join the first channel to the CSJ
by inserting the centre of the
CSJ, on an angle, to the end of
the channel where the JOIN>>
text is marked.
Push down one side of the CSJ
until you hear a ‘click’.
Step 3.
Join the second channel to the
CSJ by positioning the <<JOIN
of the channel at the centre of
the CSJ, on an angle. Push the
CSJ into the channel until you
hear a ‘click’.
Finished Channel.
The joined channels should
now look like the picture with
the CSJ positioned equally
inside of the joined channels.
Drill out holes with 3mm drill
bit in CSJ to match the holes
in channel. Drilling of screws
on the joined channels is being
done after sheets are locked on
the spliced channels.
= =
JOIN>> <<JOIN
CSJ
==
JOIN>>
J
==
JOIN>> SJ
= =
JOIN>>
<<JOIN
= =
JOIN>> <<JOIN
Finished Spliced
Channel
Channel
Push
20mm 15mm
CSJ
.
...

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30232GK
3.00mW x 2.26mD x 2.00mH
Model: 30232GK 1.22 8 28/04/2022
PRE-ASSEMBLY OF SPLICED CHANNELS
NOTE: Some channels may have holes in them - You will
need to redrill holes where CSJ joining channel covers
them.
Join together 20 x channel sections using 10 x channel joiners (Part CSJ)
2x 81AR
2x 81AL
2x 60AR
2x 60AL
1x 55AR
1x 55AL
1x 55CR
1x 55CL
1x 55BR
1x 55BL
1x 81BR
1x 81BL
2x 81CR
2x 81CL
2993mm (117.8”)
2253mm (88.7”)
81BL
55BL
55CL
55AL
60AL
81AL
81BR
55BR
55CR
55AR
60AR
81AR
= 2x 81A
= 2x 60A
= 1x 55A
= 1x 55C
= 1x 55B
= 1x 81B
= 2x 81C
81CL 81CR

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30232GK
3.00mW x 2.26mD x 2.00mH
Model: 30232GK 1.22 9 28/04/2022
Guide on Joining a Spliced Ridge Beam
Follow these three steps to assemble a ridge beam.
Step 1.
Place two ridge beams as
shown and push them together.
Slide the cap of one under the
other.
NOTE.
There is a 50mm overlap of the
ridge caps when the beams are
in position.
Step 2.
Use the ZARSP to connect at
the centre of the two ridge
beams. Be sure it is pushed in
fully.
Step 3.
Turn over the ridge beam.
Measure 250mm from the
middle along the centre of one
ridge beam, mark spacings of
50mm. Fasten with a Tek screw
at each marking.
Repeat to the other side of the
ridge beam assembly.
TIP: Predrilling each hole with
the 3mm drill bit makes it easier
to fasten.
50mm
225mm
ZARSP
Finished Spliced Ridge Beam
Finished
Joined Ridge Beams
Hex Hd Self-drilling tek screw
with neoprene washer
ZARSP
Push
Hex Driver Bit

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 30232GK
3.00mW x 2.26mD x 2.00mH
Model: 30232GK 1.22 10 28/04/2022
PRE-ASSEMBLY OF SPLICED RIDGE BEAM
.
.
1x 97AL
1x 97AR
= 1x 97A
2993mm Overall length
ZARSP
225mm
97AL 97AR
16mm
16mm