ABSCO SHEDS CYCRK Installation guide

Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 1
DOWNLOAD
OUR APP FOR
ASSEMBLY
VIDEOS
LEAVE A REVIEW
Tell us about your experience and
receive a $20 Coles Gift Card.
Visit www.abscosheds.com.au/review
AU: 1800 029 701
NZ: 0800 466 444
[email protected]
www.abscosheds.com.au
This kit is applicable to the following sheds:
The addition of this frame kit will increase the
wind rating of the specified sheds to
Wind rating: N3/C1 as per AS4055-2012.
Suitable for specific cyclonic regions
30372RK
30292RK
30222RK
30142RK
23221RK
23141RK
WARNING: This shed must be anchored to a
100mm thick concrete slab with the concrete
anchors supplied.
Failure to do so will result in the shed not
having the structural integrity required to
endure a severe storms or cyclonic event.
WARNING: Doors must remain closed with
all padbolts properly secured during severe
storms or cyclonic event.
Where information conflicts with the original
instruction manual, this document is to be
referenced.
View of frame kit applied to
30372RK
This instruction manual is to be used during
the initial construction of the structure.

Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 2
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough
understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described
and illustrated on "COMPONENTS PACKING LIST" pages.
• Local authority approval must be obtained prior to construction of the shed. Once you have
selected your site you will need to lodge a site plan to your local council.
• The bracing material supplied is 80 x 40 mm galvanised steel channel, similar to that used in steel
house framing. Some channels are required to be cut to specific lengths using a hacksaw.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately.
• If using a rebated slab ensure that all frame uprights are trimmed 25mm.
TOOLS REQUIRED
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and
safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• It is highly recommended to erect the shed with two or more people.
RECOMMENDED
3mm drill bit 6mm drill bit 10mm drill bits metal & masonry

Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 3
COMPONENT PACKING LIST
FRAME PACK
QTY COMPONENT
DESCRIPTION
PART
No. CHK QTY COMPONENT DESCRIPTION
PART
No. CHK
2BACK
WALL C2750 4 VERTICAL DOOR BRACE C1555
12
ROOF &
SIDE WALL
BRACE
C2100 6 HORIZONTAL
DOOR BRACE K0640
6BOXING C0100 16 FRONT FR
CROSS BRACE K0285
2FRONT FR
HEADER C2300 4 FRONT FR UPRIGHT C1785
2FRONT FR
UPRIGHT N1820 2 FRONT FR RAFTER M1484
2FRONT FR
WEB C0240 2 PORTAL RAFTER C1482
2PORTAL
COLUMN C1704
C Straight cut to both ends.
J20mm Tab notch on one end only
K20mm Tab notch on both ends
L45mm Lip notch on one end only
M45mm Lip notch on both ends
N20mm Tab notch + 45mm Lip notch
P20mm Tab notch + 45mm Lip notch on both ends
ROne end: 20mm Tab notch + 45mm Lip notch
SSPECIAL NOTCHING, not noted above.
FRAME SECTION IDENTIFICATION GUIDE
The first letter of the part number is used to identify the notching
type. EG. K2940, see below for reference list.
The following digits represent the overall length of the item.
EG. K2940
Part K2940 is a channel that is 2940mm long with a 20mm Tab notch
at each end.
20mm Tab
notch
45mm Lip
notch
20mm Tab
notch
+
45mm Lip
notch
4
5
4
5
2
0
2
0
2
0
C C
C
C
M
C
C
C
N
C
C
K
K

Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 4
COMPONENT PACKING LIST
FITTINGS AND ACCESSORIES
QTY COMPONENT
DESCRIPTION
PART
No. CHK QTY COMPONENT DESCRIPTION
PART
No. CHK
1INSTRUCTION
MANUAL IM 1
8G x 3/8” SELF
TAPPING SCREW
(220 PACK)
FAST001
2HINGE
6 HOLE FAST012A 8
3/16” x 1/2”
PAN HD
BOLT
FAST002
1
3mm POP
RIVET PACK
(50 PACK)
FAST009 83/16”
NYLOC NUT FAST003
24 MULTIPURPOSE
BRACKET (MPB) BKT17 3
10G x 5/8” WAFER
TEK SCREW
(300 PACK)
FAST014
1
DOUBLE DOOR
ANCHOR
BRACKET
BKT12 4PADBOLT FAST006
4CORNER
BRACKET BKT10 2PADBOLT HASP FAST007
2
M10 DYNABOLT
M10 NUT & BOLT
BRACKET (8 PACK)
ANCHOR
KIT 4
DOOR
PLATE
2 CO + 2 ZINC
12A
1
SMALL
TRIANGULAR
PLATE
ZACO190 1PHILLIPS HEAD
DRIVER BIT FAST038
3
RIDGE
CONNECTOR
PLATE
ZACO9A 13MM DRILL
BIT DRILL
2KNEE
PLATE ZACO193 12 M10 DYNABOLT FAST015
2APEX
PLATE ZACO194 50 FAST033
HEX HD
TEK SCREW W/ NEO
WASHER 10-16x16mm

Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 5
Single portal frame layout for REGENT models.
30372RK
30292RK
FRAMING OVERVIEW
• For ease of assembly front and portal frame shall be erected during initial construction of the
structure.
• Refer to FRONT FRAME ASSEMBLY for front frame specification.
*Portal frame dimension is taken from edge
of slab to centreline of portal frame.
Slab dimension specified in original manual.
Horizontal wall
framing is boxed.
Front frame is to be aligned with edge of slab rebate.
If there is no slab rebate inset it 75mm from edge of
slab.
1830mm* for 30372RK
1460mm* for 30292RK
C2750
FRONT FRAME
PORTAL FRAME
C2100
C2100
K0640
C1555