ABSCO SHEDS 15081SK User manual

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 1
Download the Absco
Sheds Assembly App
for instructional videos
MANU FACTURED
IN AUSTRALIA
SNAPTiTE
Assembly
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: 23151GK 21-11-2017
CONCRETE SLAB
2360mm
1620mm
FRONT: 2.26m
SIDE: 1.52m
HEIGHT: 1.95m
We thank you for choosing an Australian made
shed. For further assistance please visit our detailed
instructional video library at
Http://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be
number ONE, so please let us know what you think
of our instructions. Feedback makes us better.
[email protected]
CONCRETE
REBATED EDGE
BOTTOM CHANNEL
CONCRETE SLAB
75mm WIDE REBATE
100mm
WHEN LAYING YOUR CONCRETE
SLAB, ENSURE THERE IS A
REBATED EDGE 25mm DEEP
AROUND THE PERIMETER
THIS WILL HELP WATER EGRESS
FROM THE BASE OF THE SHED
Absco Industries
Premier Shed Model: 23151GK
PAGE 01
When laying concrete slab, ensure there
is a rebated edge 25mm deep around the
perimeter. This will help water egress from
the base of the shed.
AU: 1800 029 701
NZ: 0800 466 444
[email protected]
www.abscosheds.com.au
CONCRETE
SLAB
1620mm
880mm
日本更新日：2021/4/28

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 2
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough
understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described
and illustrated on "COMPONENTS PACKING LIST" pages.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately
illustrated on “FINAL CONSTRUCTION” page.
TOOLS REQUIRED
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and
safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored to a solid foundation immediately after construction is
completed.
• It is highly recommended to erect the shed with two or more people.
RECOMMENDED
3mm drill bit 10mm drill bits metal & masonry

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 3
COMPONENT PACKING LIST
Check off all components.
2
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT DESCRIPTION
PART
No. CHECK
QTY QTY
1915 X 773mm 43B
STEEL SHEET
1
1
2
1
STEEL SHEET
1915mm X 773mm X4L
STEEL SHEET
1915mm X 773mm X2R
STEEL SHEET
865mm X 773mm 43D
STEEL SHEET
1725mm X 773mm B
1
2
1
2
2
1
61B
CHANNEL
L = 786mm
CHANNEL
L = 773mm
81J
STEEL SHEET
1785mm X 711mm 34A
1
1
153A
CHANNEL
L = 1513mm
153B
CHANNEL
L = 1513mm
53C
CHANNEL
L = 1513mm
CHANNEL
L = 1513mm
81F
1
CHANNEL
L = 1513mm
81E
80A
CHANNEL
L = 1785mm
79C
CHANNEL
L = 783mm

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 4
COMPONENT PACKING LIST
Check off all components.
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT DESCRIPTION
PART
No. CHECK
QTY QTY
INSTRUCTIONS & FITTINGS PACKET
1
1
2
89A
JAMB L= 1785mm
1
1
2
2
91A
JAMB L= 1120mm
88B
LIP TRIM L= 865mm
58A
CHANNEL WITH HINGES
L = 1725mm
58B
CHANNEL
L = 1725mm
58C
CHANNEL
L = 773mm
89B
JAMB L= 1785mm
1
1ASSEMBLY
INSTRUCTIONS
12A
1DOOR
STRAP
L: 165mm
90C
JAMB L= 783mm
6SELF TAPPING
SCREW S
(20mm)
1PSTKSGL
SINGLE DOOR
FITTINGS PACK

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 5
SNAPTiTE ASSEMBLY GUIDE
The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for
tools and fasteners.
To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.
Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet.
Each perimeter channel must finish flush with the edges of the sheets. Simply tap the channel along
the sheets until each end is neatly flush. If you need to remove channels from the panels, slide it off
from the side.
Channel locks the shed panel into
position without the need for screws!
FASTENING SYMBOLS
Secure channel to sheeting by SNAPTiTE
fastening method.
Join components together with one
screw at this location only, as some
channels have extra holes that are not
required for this model of shed.
Do not join components together at
this location yet, as the screws may
obstruct further assembly of the other
components.
Join components together by pre-drill-
ing the holes first. Use one component as
template to mark where the holes are and
drill with a 3mm drill bit.
3mm pop rivet
4mm nut and bolt set.
D
SNAP
T TE
i

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 6
81E 88B
43D
43D
81E
88B
X2R
34A
B
X4L
43B
43B
22A
53B
79C
91A
89B
89A
81J
81F
61B
53C
61B
81J
53A
80A
90C
WALL AND ROOF COMPONENT OVERVIEW

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 7
REAR PANEL ASSEMBLY
1x required
43B
43B
SNAP
T TE
i
53C
SNAP
T TE
i
81F

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 8
SIDE PANEL ASSEMBLY
2x required.
X4L
X2R
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
61B
81J
80A

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 9
ROOF PANEL ASSEMBLY
43D
43D
SNAP
T TE
i
81E
88B
81E
88B
SNAP
T TE
i

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 10
FRONT PANEL ASSEMBLY
SNAP
T
TE
i
SNAP
T TE
i
34A
89A
53B
53A
79C
89B
90C
90C
53A
89A
89A
53A
90C
89A
53A
90C
89B
89B
53A
90C
79C
53B
89B
89B
53B
79C
79C
53B
89B

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 11
DOOR PANEL ASSEMBLY
Vertical door channels are
installed in the opposite
orientation compared to the
horizontal door channels.
Short flange
of channel
Long
flange of
channel
SINGLE DOOR
58C
58C
SNAP
T
TE
i
SNAP
T TE
i
12A
B
B
58B
58A

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 12
SINGLE DOOR PANEL
NOTE: Nuts and bolts are also
supplied and may be used instead of
rivets. Use a 4mm drill bit to enlarge
these holes in the jamb
NOTE: The holes to fasten the padbolt hasp are not
pre-punched to allow for proper alignment. Position
the hasp centrally over the padbolt shaft and drill 3mm
holes and secure with screws.
91A
91A
DOOR PANEL ASSEMBLY
B

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 13
PANEL CONSTRUCTION
NOTE: Take care to ensure that all wall panels are not upside down. The top channels of each panel
are pre-punched for attaching roof sheeting. The base channels are not pre-punched.
Side wall channels fit into the
notched rear wall channels.
Connect door mullion sections with six
20mm screws
Replace padbolt hasp 10mm screws
with 20mm screws
X2R
80A
89B

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 14
FINAL CONSTRUCTION
Each anchor consists of one nut, bolt, M10
dynabolt and steel angle.
Drill a 10mm hole into the wall sheet.
Drill a 10mm hole into the concrete.
Bolt and Nut*
M10 4.6/S
Steel Angle*
35 x 35 x 3
M10 Dynabolt*
* Denotes hot dip galvanised finish
Wall Sheet
Slab
Location of 8
concrete anchors
ANCHORING OF SHED

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 15
Absco Skillion Roof Shed Notes
• 1.G This instruction manual shall be read in conjunction with other consultants drawings, specifications and
written instructions provided by Absco and/or their representatives.
• 2.G The drawings provided herein are for installation and structural engineering purposes only. If discrepancies
are discovered within the documentation provided, these shall be brought to the attention of Absco and
written approvals obtained prior to commencing the affected section of work.
• 3.G If in doubt ask.
• 4.G Until approvals from the local authorities are obtained, commencement of construction from these
drawings shall not commence.
• 5.G Unless varied by the project specification, all materials and workmanship shall be undertaken in
accordance with the relevant Australian standards and the by-laws and ordinances of the relevant building
authorities.
• 6.G All dimensions indicated in these drawings shall be verified on site by the installation contractor. Scaling
of drawings shall not be undertaken.
• 7.G Prior to commencing works on site, the contractor shall verify the position of all services in the area to
ensure that the construction does not interfere with any of those services.
• 8.G During installation on site the shed structures shall be maintained in a stable condition with no part
becoming overstressed or permanently deformed.
• 9.G In circumstances where the shed has been installed in a manner which is inconsistent with the installation
manual, structural certification shall be void.
• 10.G The structural components detailed within this installation manual have been designed for the following
loads in accordance with AS/NZS1170 based on a Class 10a, Type 2 structure:
• Roof Live Load: 0.25 kPa uniformly distributed or 1.1 kN concentrated as per AS/NZS1170.1
• Wind Load: Classification N2, Non-Cyclonic to AS4055 where Vu = 40 m/s, Vs = 26 m/s
Windward wall Cpe = 0.7
Leeward Wall Cp,e = -0.3 to -0.5 as applicable based on shed geometry
Side Wall Cp,e = -0.5 to -0.65 as applicable based on shed geometry
Roof Cp,e = -0.5 to -1.3 depending on wind direction
6-12 Activity St, Acacia Ridge QLD 4110
PO Box 119, Acacia Ridge QLD 4110
AU: 1800 029 701
NZ: 0800 466 444
[email protected]
www.abscosheds.com.au
General

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 16
Absco Skillion Roof Shed Notes
• 1.S All structural steelwork shall have a corrosion protection system applied consistent with AS/NZS 2312-
2002.
• 2.S All structural steelwork detailed within this installation manual shall be minimum Grade 550 for roll formed
sections (including roof and wall sheeting) and Grade 250 for angle sections.
• 3.S All roof, and wall sheeting shall be minimum base metal thickness of 0.3mm
• 4.S All snaptite channels and jambs shall be minimum base metal thickness of 0.42mm
• 5.S All top hats shall be minimum base metal thickness of 1.0mm
• 6.S All screw fasteners shall be Phil Pan Head Zinc Plated #8 x 3/4” (STP0820)
• 7.S All bolt fasteners for anchoring shall be M10 minimum grade 4.6/S
• 8.S Installation of screw fasteners shall generally be undertaken in accordance with the relevant provisions
of AS1562.
Steelwork
• 1.F The supporting slab foundation for the garden shed shall be of a minimum size indicated on the installation
manual. The top surface of the formed slab shall be level and free of any irregularities which would inhibit
the installation of the shed.
• 2.F The structural engineering design for the supporting slab foundation shall be undertaken by a suitably
qualified structural engineer. The design shall consider all relevent provision of AS3600 and AS2870.
• 3.F Between adjacent footings or excavations, the contractor installing the slab foundation shall not exceed
a rise of 1 in a run of 2 in line of slope.
• 4.F Unless approved in writing by the slab foundation engineer, the limits of excavations near existing
footings shall be in accordance with that indicated below.
Supporting Slab and Foundations
The contactor shall undertake investigatory
localised excavations near existing
footings to ascertain their depth prior to
excavating adjacent to them. It is noted that
excavating to a depth below that indicated
above shall not be undertaken without
the written approval from the engineer.

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 17
Absco Sheds Storage Guidelines
• Absco Sheds are designed to be weatherproof for normal weather conditions. In the event of extreme
weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins,
screw fixings etc., may exhibit minor deformations which may allow some water entry. These areas should be
checked regularly to ensure that maximum strength and protection is maintained.
• Other weather conditions such as extreme heat and extreme cold, moist or dry air can influence the effects
of concrete floor moisture and/or condensation on the underside of the roof sheets.
• Absco Sheds and storage units are primarily used for storage of garden equipment such as lawnmowers,
wheelbarrows, garden tools etc. Storage items that might be adversely affected by any of the above conditions
may require additional protection such as being sealed or covered by plastic sheets and/or stacked above
the concrete floor on timber slats.
• Waterproof sealants may be used to offer further protection where required around joins and screw fixings,
as can rubber door seals and other products which are available from most hardware outlets.
• Placement of waterproof sealants (silicone) between the base of the shed and concrete slab is not
recommended, as this process can have a reverse effect, preventing excess water from escaping, resulting
with water accumulating and being trapped inside the shed.
• Absco accepts no responsibility for water entry, floor moisture, condensation or the condition of the Contents
inside your Absco steel building arising from any of the pre-mentioned weather conditions.
6-12 Activity St, Acacia Ridge QLD 4110
PO Box 119, Acacia Ridge QLD 4110
AU: 1800 029 701
NZ: 0800 466 444
[email protected]
www.abscosheds.com.au

Absco Industries Assembly Instruction Manual
ABSCO SPACESAVER SHED
MODEL: 15081SK
1.52mW x 0.78mD x 1.80mH, 1.95mH
Model: 15081SK 11/11/19 1.1 18
Australia Product Warranty Against Defects
• Absco Sheds, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports
are made using high quality Australian made steel.
• We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for20
yearsfrom date of purchase, when installed within Australia.
• This warranty does not apply to surface deterioration of panels caused by ‘Swarf” (Tiny particles of
steel debris left from cutting, grinding or drilling operations) that has not been removed after building
construction, or as a result of contact with damp soil, chemicals, fertilisers or other corrosive substances.
• This warranty covers any Absco product used for normal domestic use and installed in accordance with the
installation instructions.
• The warranty does NOT cover Damage caused by storms, wind, rain snow or poor foundations.
• This warranty does NOT cover ABSCO products installed in severe coastal, industrial or other highly
corrosive environments. The warranty does not cover fasteners (screws, nuts, bolts, rivets, hasps or sliding
padbolts).
• The warranty is limited to replacement and delivery of components and does not include any labour or
installation costs. The benefits given by the warranty are in addition to your other rights and remedies
under a law in relation to the goods or services to which the warranty relates.
• The warranty applies to the exclusion of all other representations, guarantees or warranties express or
implied, our goods come with guarantees that cannot be excluded under the Australian consumer law and
is not transferable. You are entitled to a replacement or refund for a major failure and for compensation
for any other foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of an acceptable quality and the failure does not amount to a major failure. For further
information go to http://www.consumerlaw.gov.au
• Please retain a proof of purchase (sales docket or invoice) or register your warranty within 30 days of
purchase here: www.absco.com.au/register_warranty.php
• In the unlikely event a warranty claim is made, it must be supported by photographic evidence and details
of the defect, including component part numbers, together with proof of purchase documentation (or
on-line registration of purchase) and forwarded to the address below. Upon receipt of the warranty claim,
the Customer Service Manager will contact you within three business days to advise you of the assessment
outcome of the claim, which may include your expenses incurred in making the claim.
THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 119 ACACIA RIDGE QLD AUSTRALIA 4110
PHONE: [phone]FAX: [phone]EMAIL: [email protected]
Issued 01 January 2018