ABSCO SHEDS 30151SK User manual

CONCRETE SLAB
PAGE 1
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
We thank you for choosing an Australian made shed. For further assistance please
visit our detailed instructional video library at
Http://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be number ONE, so please let us
know what you think of our instructions. Feedback makes us better.
[email protected]
10mm
50mm
WHEN LAYING YOUR CONCRETE
SLAB, CHAMFER THE 50mm EDGES
DOWNWARDS BY 10mm.
50mm
THIS WILL ENSURE THAT
CLEAR FROM YOUR SHED
WATER RUN OFF IS KEPT
3100mm
1620mm
FRONT BASE
LENGTH: 3.0m
SIDE BASE
LENGTH: 1.52m
FRONT WALL
HEIGHT: 1.8m
REAR WALL
HEIGHT: 2.08m
Absco Space Saver Shed
Assembly Instructions
Model: 30151SK

PAGE 2
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
GENERAL INSTRUCTIONS
A NOTE ON SAFETY
·Some parts may have sharp edges. It is advisable to wear gloves when
handling these items and safety glasses if drilling holes. Sensible shoes
are highly recommended.
·Do not erect your shed in windy conditions, ensure that the shed is
securely anchored to a solid foundation immediately after construction is
completed.
·It is highly recommended to erect the shed with two or more people.
TOOLS REQUIRED
Normal: 4mm & 10mm
OPTIONAL
SITE PREPARATION
Masonry: 10mm
·The site for the shed must be level. An uneven surface may result in misalignment of
parts.
·It is recommended that the shed be set on a 100mm concrete slab and anchored down
appropriately (refer to last page for details).
·Anchor sets are not supplied as standard items with this product as some customers
wish to use their own anchoring systems.
·Before commencing any assembly, read through these instructions in
detail to gain a thorough understanding of assembly methods and
associated details.
·Unpack the carton and carefully identify and check off all the parts
against the parts described and illustrated on pages three and four.

COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS
PAGE 3
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
2
COMPONENT
DESCRIPTION PART
No. CHECK COMPONENT
DESCRIPTION PART
No. CHECK
QTY QTY
1
2045 X 773mm 262
STEEL SHEET
2
1
1
1
1
4
1
2045 X 773mm 263
STEEL SHEET
STEEL SHEET
1915mm X 773mm 260L
STEEL SHEET
1915mm X 773mm 260R
STEEL SHEET
2045mm X 773mm 261L
STEEL SHEET
2045mm X 773mm 261R
STEEL SHEET
1725mm X 773mm B
2
2
1
CHANNEL
L = 1513mm 81E
1
2
58A
CHANNEL WITH HINGES
L = 1725mm
58B
CHANNEL
L = 1725mm
58C
CHANNEL
L = 773mm
STEEL SHEET
1610mm X 773mm 43S
61D
CHANNEL
L = 1530mm
79B
CHANNEL
L = 788mm
1785 X 773mm 30A
STEEL SHEET
1
1785 X 731mm 32A
STEEL SHEET
1785 X 731mm 33A
STEEL SHEET
1
1

1
1
1
1
2
55BL
CHANNEL
L = 1496.5mm
81BL
CHANNEL
L = 1496.5mm
81AL
CHANNEL
L = 1496.5mm
56AL
CHANNEL
L = 1496.5mm
56BL
CHANNEL
L = 1496.5mm
COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS
PAGE 4
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
COMPONENT
DESCRIPTION PART
No. CHECK COMPONENT
DESCRIPTION PART
No. CHECK
QTY QTY
1
1
1
1
2
55BR
CHANNEL
L = 1496.5mm
81BR
CHANNEL
L = 1496.5mm
81AR
CHANNEL
L = 1496.5mm
56AR
CHANNEL
L = 1496.5mm
56BR
CHANNEL
L = 1496.5mm
CSJ
6
THESE COMPONENTS ARE TO BE
JOINED TO THESE COMPONENTS
CHANNEL JOINER
L= 200mm (7.9")

PAGE 5
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
64mm CSK SCREW &
NUT SECURE HINGES
TO DOOR
220 SELF TAPPING
SCREWS 1DOOR
PADBOLT
1DOOR
PADBOLT
HASP
63mm POP RIVETS SECURE
HINGES TO DOOR
(ALTERNATIVE FIXING
METHOD)
1ASSEMBLY
INSTRUCTIONS
COMPONENT
DESCRIPTION PART
No. CHECK COMPONENT
DESCRIPTION PART
No. CHECK
QTY QTY
CONTENTS OF FITTINGS PACKET
COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS
12A
1DOOR
STRAP
L: 165mm
22A
89A
JAMB L= 1785mm
1
1
2
2
91A
JAMB L= 1120mm
88J
LIP TRIM L= 1610mm
90B
JAMB L= 788mm
89B
JAMB L= 1785mm
1

20mm 15mm
QTY = 10pcs.
CHANNEL
(0.79") (0.59")
PUSH PUSH
CHANNEL
CSJ
PAGE 6
INSTRUCTIONS FOR JOINING SPLICED CHANNELS
CSJ
CSJ
HIGH-SIDE
CHANNEL
LOW-SIDE
CHANNEL
CSJ
CSJ
CSJ
= =
= =
==
=
=
STEP 1.
Position the channels and the CSJ
joiner channel so the center of the
CSJ is in line with the end of each
channel to be joined together.
STEP 2.
Join the first channel to the CSJ by inserting the center
of the CSJ (on an angle) to the end of the channel
where the JOIN>> text is marked. Push down one side
of the CSJ until you hear a 'click'.
STEP 3.
Join the second channel to the CSJ
by positioning the <<JOIN end of the
channel at the center of the CSJ
(on an angle). Push the CSJ into
the channel until you here a 'click'.
=
The joined channels should now
look like the picture above with the
CSJ positioned equally inside of the
joined channels.
FINISHED CHANNEL
=
NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER.
JOIN>> <<JOIN JOIN>> JOIN>> SJ
JOIN>>
<<JOIN
JOIN>> <<JOIN
J
CSJ
DRILL 4mm (0.16") x 3mm (0.12")
(2 PER A SIDE) HOLES TO
SECURE SECTIONS TOGETHER.
(THESE SCREWS MAY HAVE TO
BE TEMPORARILY REMOVED
AND REPLACED DURING LATER
ASSEMBLY)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK

PAGE 7
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
=
=
=
=
=
2993mm (117.8")
STEP 1. PRE-ASSEMBLY OF SPLICED CHANNELS
2 x 81A
1 x 56A
1 x 56B
1 x 55B
1 x 81B
NOTE: JOIN TOGETHER 12 X CHANNEL SECTIONS USING 6 X CHANNEL JOINERS (PART CSJ)
81BR
81BL
55BL
55BR
56BR
56BL
56AL
56AR
81AL
81AR
2 X 81AR
2 X 81AL
1 X 56AR
1 X 56AL
1 X 56BR
1 X 56BL
1 X 55BR
1 X 55BL
1 X 81BR
1 X 81BL
NOTE: SOME CHANNELS HAVE
HOLES IN THEM - YOU WILL NEED
TO RE-DRILL HOLES ON ANY
CHANNEL WHERE THE CSJ
JOINING CHANNEL COVERS
HOLES ON THE CHANNELS
YOU ARE CONNECTING
Absco Space Saver Shed
Model: 30151SK

VIEW OF ROOF COMPONENTS
NO. PAGE 8
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
43S
43S
43S
43S
88J
81A
88J 81A
Absco Space Saver Shed Model: 30151SK

VIEW OF WALL COMPONENTS
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
PAGE 9
81E
81B
55B
61D
260L
261L
260R
261R
262
263
263
262
61D 32A
22A
56A
90B
30A
56B
89A
79B
33A
91A
91A
89B
81E
B

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
ABSCO ASSEMBLY INTRODUCTION
FASTENING SYMBOLS
The snaptite assembly system locks most perimeter channels to all roof and wall
sheets without the need for tools and fasteners.
To pre-assemble the four wall panels
and two roof panels, the perimeter
channels are secured to the top and
bottom of each panel using the
snaptite system, as detailed on the
following pages wherever you see
the symbol.
Position sheets on timbers,
trestles or partly over edge of
concrete slab.
Each perimeter channel must finish flush with the
edges of the sheets.The snaptite system allows
adjustment for this process by simply tapping the
channel along the sheets until each end is neatly flush.
If you need to remove channels from the panels, pull
the channel along the panel from opposing ends. You
may need someone to help with this.
Join components together with one screw at this
location only, as some channel sections have extra
holes that are not required for this model of garden
shed
Do not join components together at this location yet,
as the screw may obstruct further assembly of other
components
4mm NUT & BOLT SET
3mm POP RIVETS
PUSH
PUSH
HIGH SIDE
HIGH SIDE
PUSH
HIGH SIDE
HIGH SIDE
After joining sheets together, position channel over one end of the sheets, gently
tapping it over the snaptite lugs, working along the sheets to the other end.
HIGH SIDE
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
Join components together by pre-drilling the holes
first. Use one component as a template to mark where
the holes are. Drill with 3mm drill bit.
D
PAGE 10

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16 PAGE 11
Absco Space Saver Shed
Model: 30151SK
6. DOOR PANEL ASSEMBLY
20mm FLANGE
58C
58C
58A
15mm FLANGE
B
B
SNAP
T TE
i
SNAP
T TE
i
58B
12A
ALL VERTICAL DOOR CHANNELS ARE INSTALLED IN THE REVERSE
DIRECTION IN COMPARISON TO HORIZONTAL DOOR CHANNELS

REAR PANEL ASSEMBLY
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
PAGE 12
262
263
263
262
SNAP
T TE
i
SNAP
T TE
i
55B
81B

PAGE 13
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
260L
261L
261R
260R
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
SIDE PANEL ASSEMBLY
1 x LEFT SIDE PANEL
1 x RIGHT SIDE PANEL
61D
81E
81E
61D

ROOF PANEL ASSEMBLY
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
PAGE 14
43S
43S
43S
43S
SNAP
T TE
i
SNAP
T TE
i
81A
88J
81A
88J

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
PAGE 15
FRONT PANEL ASSEMBLY
89B
89A
32A
33A
30A
56A
79B
56B
90B
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
DOOR PANEL ASSEMBLY
NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for
proper alignment. position each hasp centrally over the padbolt shaft, and drill 3mm holes and secure with screws
NOTE: Nuts and bolts (supplied) may be used instead of
pop rivets (supplied) by simply enlarging the hinge hole
sets in the jamb using a 4mm drill bit
91A
91A
B
PAGE 16

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
PANEL CONSTRUCTION
NOTE: Take care to ensure that both front
and rear wall panels are not positioned
upside down. The top channel of each
panel is pre-punched for attaching roof
sheet. The base channels are not
pre-punched.
SIDE WALL PANEL CHANNELS FIT
INTO THE NOTCHED FRONT AND
REAR WALL PANEL CHANNELS
PAGE 17

FINAL CONSTRUCTION ANCHORING OF SHED
LOCATION OF 12
CONCRETE ANCHORS
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30151SK 15/04/16
Absco Space Saver Shed
Model: 30151SK
DYNABOLT
BOLT & NUT
STEEL
ANGLE
SLAB
WALL
SHEET
- EACH ANCHOR CONSISTS OF ONE NUT, BOLT,
DYNABOLT AND STEEL ANGLE
- DRILL A 10mm HOLE INTO THE WALL SHEET
- DRILL A 10mm HOLE INTO THE CONCRETE
PAGE 18

1 | P a g e
AUSTRALIA PRODUCT WARRANTY
AGAINST
DEFECTS
Congratulations on your purc ase of an ABSCO SHED
ABSCO SHEDS, including garden s eds, garden beds, aviaries, storage units, garages,
awnings and carports are made using ig quality Australian made steel.
We are pleased to advise we warrant t at t e steel coating will not rust, crack, flake peel or
blister for 20 years from date of purc ase, w en installed wit in Australia.
T is warranty does not apply to surface deterioration of panels caused by ‘Swarf” (Tiny
particles of steel debris left from cutting, grinding or drilling operations) t at as not been
removed after building construction, or as a result of contact wit damp soil, c emicals,
fertilisers or ot er corrosive substances.
T is warranty covers any Absco product used for normal domestic use and installed in
accordance wit t e installation instructions. T e warranty does NOT cover Damage caused
by storms, wind, rain snow or poor foundations.
T is warranty does NOT cover ABSCO products installed in severe coastal, industrial or ot er
ig ly corrosive environments. T e warranty does not cover fasteners (screws, nuts, bolts,
rivets, asps or bolts).
T e warranty is limited to replacement and delivery of components and does not include any
labour or installation costs. T e benefits given by t e warranty are in addition to your ot er
rig ts and remedies under a law in relation to t e goods or services to w ic t e warranty
relates.
T e warranty applies to t e exclusion of all ot er representations, guarantees or warranties
express or implied, our goods come wit guarantees t at cannot be excluded under t e
Australian consumer law and is not transferable. You are entitled to a replacement or refund
for a major failure and for compensation for any ot er foreseeable loss or damage. You are
also entitled to ave t e goods repaired or replaced if t e goods fail to be of an acceptable
quality and t e failure does not amount to a major failure. For furt er information go to
ttp://www.consumerlaw.gov.au.
Please retain a proof of purc ase (sales docket or invoice) or register your warranty wit in 30
days of purc ase ere: www.absco.com.au/register_warranty.p p
In t e unlikely event a warranty claim is made, it must be supported by p otograp ic evidence
and details of t e defect, including component part numbers, toget er wit proof of purc ase
documentation (or on-line registration of purc ase) and forwarded to t e address below.
Upon receipt of t e warranty claim, t e Customer Service Manager will contact you wit in
t ree business days to advise you of t e assessment outcome of t e claim, w ic may include
your expenses incurred in making t e claim.
THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 119 ACACIA RIDGE QLD AUSTRALIA 4110
PHONE: [phone] FAX: [phone] EMAIL: warr[email protected]
Issued 01 January 2012

2 | P a g e
ABSCO SHEDS - STORAGE GUIDELINES
ABSCO SHEDS include garden s eds, garden beds, storage units, aviaries,
garages, awnings and carports.
ABSCO SHEDS are designed to be weat erproof for normal weat er
conditions. In t e event of extreme weat er conditions suc as eavy rain,
combined wit ig wind gusts, t e ridge capping, s eeting joins, screw
fixings etc., may ex ibit minor deformations w ic may allow some water
entry. T ese areas s ould be c ecked regularly to ensure t at maximum
strengt and protection is maintained.
Ot er weat er conditions suc as extreme eat and extreme cold, moist or
dry air can influence t e effects of concrete floor moisture and/or
condensation on t e underside of t e roof s eets.
ABSCO SHEDS and storage units are primarily used for storage of garden
equipment suc as lawnmowers, w eelbarrows, garden tools etc. Storage
items t at mig t be adversely affected by any of t e above conditions may
require additional protection suc as being sealed or covered by plastic
s eets and/or stacked above t e concrete floor on timber slats.
Waterproof sealants may be used to offer furt er protection w ere required
around joins and screw fixings, as can rubber door seals and ot er products
w ic are available from most ardware outlets.
Placement of waterproof sealants (silicone) between t e base of t e s ed
and concrete slab is not recommended, as t is process can ave a reverse
effect, preventing excess water from escaping, resulting wit water
accumulating and being trapped inside t e s ed.
Absco accepts no responsibility for water entry, floor moisture,
condensation or t e condition of t e Contents inside your Absco steel
building arising from any of t e pre-mentioned weat er conditions.