ABSCO SHEDS ABSCO PREMIER SHED User manual

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 1 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
CONCRETE SLAB
PAGE 1
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14
10' 2 3⁄64"
10' 2 3⁄64"
FRONT: 9' 10 7⁄64"
SIDE: 9' 10 7⁄64"
HEIGHT: 6' 10 43⁄64"
Absco Premier Garden Shed
Assembly Instructions
Model: J30302G
We thank you for choosing an Australian Made Shed. For further assistance please
visit our detailed instructional video library at
www.abscosheds.com.au/USA
At ABSCO Industries we are always looking to be number ONE, so please let us
know what you think of our instructions. Feedback makes us better.
[email protected]
WHEN LAYING YOUR CONCRETE
SLAB, ENSURE THERE IS A REBATED
EDGE 1" DEEP AROUND THE PERIMETER
CONCRETE
SLAB
REBATED EDGE
CHANNEL
CONCRETE SLAB
3" WIDE
REBATE
THIS WILL HELP
WATER EGRESS FROM
THE BASE OF THE SHED
4”
10’ 2”
10’ 2”
AU: 1800 029 701
N Z: 0800 466 444
[email protected]
www.abscosheds.com.au
[phone]

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 2 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
Premier Garden Shed - Model: J30232G
PAGE 2
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30232G 26/02/14
GENERAL INSTRUCTIONS
A NOTE ON SAFETY
The site for the shed must be level.
It is recommended that the shed be set on a 4" concrete slab and
anchored down appropriately (refer last page for details).
Anchor sets are not supplied as standard items with this product.
Before commencing any assembly, read through these instructions in
detail to gain a thorough understanding of assembly methods and
associated details.
Unpack the carton and carefully identify and check off all the parts
against the parts described and illustrated on pages three and four.
Some parts may have sharp edges. It is advisable to wear gloves when
handling these items and safety glasses if drilling holes. Sensible shoes
are highly recommended.
Do not erect your shed in windy conditions, ensure that the shed is
securely anchored to a solid foundation immediately after construction is
completed.
It is highly recommended to erect the shed with two or more people.
TOOLS REQUIRED
SITE PREPARATION
Normal 1/8", 11/64"
Masonry 25/64"
Normal 25/64"
OPTIONAL
Standard 1/8”
and 11/69” Standard 25/64”
Masonary 25/64”
80+ lbs

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 3 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
STEEL SHEET
5' 10 9⁄32" Long
2' 6 7⁄16" Wide
30A
2
STEEL SHEET
5' 10 9⁄32" Long
2' 6 7⁄16" Wide 31A
2
STEEL SHEET
6' 3 25⁄64" Long
2' 6 7⁄16" Wide
36L
2
STEEL SHEET
6' 3 25⁄64"
2' 6 7⁄16" Wide
36R
2
90A
JAMB L= 5' 1 47⁄64"
1
91A
JAMB L= 3' 8 3⁄32"
4
87A
LIP TRIM L= 5' 55⁄64"
4
15A
2PEAK BRACE
2CHANNEL
L = 4' 11 49⁄64"
84L
58B
1CHANNEL
L = 5' 7 29⁄32"
58A
2CHANNEL WITH HINGES
L = 5' 7 29⁄32"
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY QTY
STEEL SHEET
5' 10 9⁄32" Long
2' 3 63⁄64" Wide
34A
2
STEEL SHEET
5' 7 29⁄32" Long
2' 6 7⁄16" Wide
A
1
89C
JAMB L= 5' 7 29⁄32"
1
89A
JAMB L= 5' 10 9⁄32"
2
STEEL SHEET
6' 8 33⁄64" Long
2' 6 7⁄16" Wide
38R
2
STEEL SHEET
5' 55⁄64" Long
2' 6 7⁄16" Wide
45A
8
STEEL SHEET
6' 8 33⁄64" Long
2' 6 7⁄16" Wide 38L
2
STEEL SHEET A
5' 7 29⁄32" Long
2' 6 7⁄16" Wide
B
1
Part No. Here
Part No. Here
Part No. Here
Part No. Here
COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 4 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
58C
4CHANNEL
L = 2' 6 7⁄16"
2CHANNEL
L = 14' 11 49⁄64"
84R
79A
1CHANNEL
L = 5' 1 47⁄64"
14A
2CAP GABLE
L: 6 11/16"
8
5/32" NUT & BOLT SET
SECURE TWO
PADBOLTS TO DOOR
SHEET
220 SELF TAPPING
SCREWS 3DOOR
PADBOLT
2
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY QTY
CONTENTS OF FITTINGS PACKET
COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS
12A
2
DOOR
STRAP
L: 6 1/2"
22A
81
1
1
SELF DRILLING HEX
HEAD TEK SCREWS (NO
HOLE REQUIRED) 1/8" DRILL BIT
HEX TEK SCREW
DRIVER BIT
RIVET GUN
12 POP RIVETS SECURE
HINGES TO DOOR 12
11/64" CSK SCREW &
NUT SECURE HINGES
TO DOOR
(ALTERNATE METHOD)
DOOR
PADBOLT
HASP

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 5 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS
55AL
55CL
55BL
81BL
81AL
60AL
97AL
55CR
1
1
1
1
4
2
1RIDGE
BEAM
THESE COMPONENTS ARE TO BE
JOINED
TO THESE COMPONENTS
1
1
1
1
4
2
1
CHANNEL
L = 4' 10 59⁄64"
55BR
81BR
81AR
60AR
97AR
55AR
RIDGE
BEAM
L = 4' 11 7⁄8"
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY
CSJ
QTY
10 ZARSP 1
CHANNEL JOINER
L= 7 7/8"
RIDGE BEAM JOINER
L: 1' 5 23⁄32"
CHANNEL
L = 4' 10 59⁄64"
CHANNEL
L = 4' 10 59⁄64"
CHANNEL
L = 4' 10 59⁄64"
CHANNEL
L = 4' 10 59⁄64"
CHANNEL
L = 4' 10 59⁄64"
CHANNEL
L = 4' 10 59⁄64"
CHANNEL
L = 4' 10 59⁄64"
CHANNEL
L = 4' 10 59⁄64"
CHANNEL
L = 4' 10 59⁄64"
CHANNEL
L = 4' 10 59⁄64"
CHANNEL
L = 4' 10 59⁄64"
L = 4' 11 7⁄8"
81BR
JOIN >>
81BL
JOIN >>
55BR
JOIN >>
55BL
JOIN >>
55CR
JOIN >>
55CL
JOIN >>
55AR
JOIN >>
55AL
JOIN >>

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 6 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
PUSH PUSH
Premier Garden Shed - Model: J30232G
PAGE 6
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30232G 26/02/14
INSTRUCTIONS FOR JOINING SPLICED CHANNELS
CSJ
HIGH-SIDE
CHANNEL
LOW-SIDE
CHANNEL
CSJ
CSJ
CSJ
= =
= =
==
=
=
STEP 1.
Position the channels and the CSJ
joiner channel so the center of the
CSJ is in line with the end of each
channel to be joined together.
STEP 2.
Join the first channel to the CSJ by inserting the center
of the CSJ (on an angle) to the end of the channel
where the JOIN>> text is marked. Push down one side
of the CSJ until you hear a 'click'.
STEP 3.
Join the second channel to the CSJ
by positioning the <<JOIN end of the
channel at the center of the CSJ
(on an angle). Push the CSJ into
the channel until you here a 'click'.
=
The joined channels should now
look like the picture above with the
CSJ positioned equally inside of the
joined channels.
FINISHED CHANNEL
=
NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER.
JOIN>> <<JOIN JOIN>>
JOIN>> SJ
JOIN>>
<<JOIN
JOIN>> <<JOIN
J
CSJ
DRILL 4 x 1/8" (2 PER SIDE)
HOLES TO SECURE SECTIONS
TOGETHER. (THESE SCREWS
MAY HAVE TO BE TEMPORARILY
REMOVED AND REPLACED
DURING LATER ASSEMBLY)
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 7 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
Premier Garden Shed - Model: J30302G
PAGE 7
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14
=
=
=
=
=
=
2 X 60AR
9' 9 53⁄64"
4 x 81A
2 x 60A
1 x 55A
1 x 55C
1 x 55B
1 x 81B
NOTE: JOIN TOGETHER 20 X CHANNEL SECTIONS USING 10 X CHANNEL JOINERS (PART CSJ)
81BL
81BR
55BR
55BL
55CL
55CR
55AR
55AL
60AL
60AR
81AR
81AL
4 X 81AR
4 X 81AL
2 X 60AL
1 X 55AR
1 X 55AL
1 X 55CR
1 X 55CL
1 X 55BR
1 X 55BL
1 X 81BR
1 X 81BL
NOTE: SOME CHANNELS HAVE
HOLES IN THEM - YOU WILL NEED
TO RE-DRILL HOLES ON ANY
CHANNEL WHERE THE CSJ
JOINING CHANNEL COVERS
HOLES ON THE CHANNELS
YOU ARE CONNECTING
STEP 1. PRE-ASSEMBLY OF SPLICED CHANNELS
INSTRUCTIONAL
VIDEOS
IMPORTANT:
SOME CHANNELS HAVE

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 8 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
Premier Garden Shed - Model: J30302G
PAGE 9
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14
TEK SCREW DRIVER BIT
QTY. = 1
QTY. = 8
QTY. = 2
QTY. = 1
SELF DRILLING TEK SCREW
PART ZARSP - 1' 5 23⁄32"
ZARSP
RIDGE BEAM 4' 11 7⁄8"
PARTS 97AL & 97AR
STEP 2. PRE-ASSEMBLY OF SPLICED RIDGE BEAM
97AL
97AR
5/8"
7 7/8"
9 27⁄32"
9' 9 53⁄64" OVERALL LENGTH
(PART 97A)
5/8"
THE TOP SECTIONS OF
CAPPING WILL OVERLAP
EACH OTHER AT THE
JOIN BY 2.0".
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 9 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
PAGE 8
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30232G 26/02/14
STAGE 1: PUSH RIDGE BEAMS TOGETHER, MAKE SURE THERE IS A 2" OVERLAP
OF THE RIDGE CAP
STAGE 2: INSERT RIDGE CAP JOINER INTO CONNECTED RIDGE CAPS.
MAKE SURE JOINER HAS 8 55/64" IN EACH RIDGE CAP.
STAGE 3: TURN RIDGE CAP OVER AND MEASURE 9 27⁄32" FROM THE END
OF EACH RIDGE CAP.
PLACE TEK SCREWS IN 2" INCREMENTS FROM SAID END.
REPEAT THIS PROCESS FOR THE OPPOSING HALF OF RIDGE BEAM
INSTRUCTIONS FOR JOINING SPLICED RIDGE BEAM
2"
8 55⁄64"
2"
2"
Premier Garden Shed - Model: J30232G
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 10 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
Premier Garden Shed - Model: J30302G
87A
60A
14A
87A
81A
87A
87A
VIEW OF ROOF COMPONENTS
14A
81A
97A
45A
45A
45A
45A
45A
45A
45A
45A
PAGE 10
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 11 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
VIEW OF WALL COMPONENTS
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14 PAGE 11
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 12 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
PAGE 12
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
Premier Garden Shed
Model: 30152GK
INSTRUCTIONS
AND VIDEOS
ABSCO ASSEMBLY INTRODUCTION
FASTENING SYMBOLS
The snaptite assembly system locks most perimeter channels to all roof and wall
sheets without the need for tools and fasteners.
To pre-assemble the four wall panels
and two roof panels, the perimeter
channels are secured to the top and
bottom of each panel using the
snaptite system, as detailed on the
following pages wherever you see
the symbol.
Position sheets on timbers,
trestles or partly over edge of
concrete slab.
Each perimeter channel must finish flush with the
edges of the sheets.The snaptite system allows
adjustment for this process by simply tapping the
channel along the sheets until each end is neatly
flush. If you need to remove channels from the
panels, pull the channel along the panel from
opposing ends. You may need someone to help
with this.
Join components together with one screw at this
location only, as some channel sections have extra
holes that are not required for this model of garden
shed
Do not join components together at this location yet,
as the screw may obstruct further assembly of other
components
4mm NUT & BOLT SET
3mm POP RIVETS
PUSH
PUSH
HIGH SIDE
HIGH SIDE
PUSH
HIGH SIDE
HIGH SIDE
After joining sheets together, position channel over one end of the sheets, gently
tapping it over the snaptite lugs, working along the sheets to the other end.
HIGH SIDE
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
Join components together by pre-drilling the holes
first. Use one component as a template to mark where
the holes are. Drill with 3mm drill bit.
D

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 13 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
DOOR PANEL ASSEMBLY
25/32" FLANGE
58C
58C
58C
12A
58C
Premier Garden Shed - Model: J30232G
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30232G 26/02/14
PAGE 13
58A
58A
19/32" FLANGE
A
B
89C
58B
A
B
FOUR HOLE SET
FOR PADBOLT
CONNECTION
ATTACH 58A AND 58B TO SHEET B SO THAT
THE 25/32" SIDE OF THE CHANNELS ARE ON
THE OUTSIDE OF SHEET B
ENSURE CHANNEL 58C
OUTER FLANGE SITS OVER
UPRIGHT CHANNEL FLANGE
ATTACH 58C CHANNELS
AS DESCRIBED ON PAGE 12
ATTACH 89C WITH COLORED
SIDE FACING OUT.
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 14 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
INSIDE
OF
SHED
REAR PANEL ASSEMBLY
SIDE PANEL ASSEMBLY
(2 Required)
PAGE 14
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14
55B
81B
Premier Garden Shed -
Model: J30302G
TRIM THE TIP OF EACH
SHEET OR BEND OUT OF THE
WAY TO ALLOW CHANNELS
TO FIT HARD UP TO THE
EDGE OF THE SHEET
30A
31A
31A
30A
36L
38L
38R
36R
84R
81A
84L
15A
LAY SHEETS OUT AS SHOWN
LAY SHEETS OUT AS SHOWN
INSTALL PEAK BRACE WITH OVERHANG FITTING INSIDE SHED
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 15 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
2 x PRE-PUNCHED
HOLES TO THIS
END OF EACH
SHEET WITH PART
NO. 81A FITTED
ROOF PANEL ASSEMBLY
(2 Required)
PAGE 15
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14
Premier Garden Shed -
Model: J30302G
45A
45A
45A
45A
87A
81A
87A
60A
LAY SHEETS OUT AS SHOWN
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 16 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
FRONT PANEL ASSEMBLY
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30232G 26/02/14
89A
89A
55A
90A
79A
55C
34A
34A
PAGE 16
Premier Garden Shed - Model: J30232G
NOTCH ON JAMB 90A FITS OVER JAMB 89A AND 89B
AND NOTCH ON 89B AND 89A FITS OVER 55A
NOTCH ON JAMB 89A AND 89B FITS
OVER CHANNEL 55C AND CHANNEL
79A INSERTS INTO 55C WITH
SHORTEST SIDE FACING OUT.
DO NOT INSTALL THIS SCREW
(OR THE TOP EQUIVALENT)
UNTIL CHANNELS 55A AND 55C
ARE INSTALLED
79A
55C
89A
LAY SHEETS OUT AS SHOWN
55A
55A
90A
89A
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 17 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
DOOR PANEL ASSEMBLY
NOTE: Nuts and bolts (supplied) may be
used instead of pop rivets (supplied) by
simply enlarging the hinge hole sets in the
jamb using a 5/32" drill bit
PAGE 17
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
91A
91A
A
B
Premier Garden Shed
Model: 30152GK
INSTRUCTIONS
AND VIDEOS
NOTE: The two holes required to connect the padbolt hasp for ea
NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for ch door have not been pre-punched, to allow for
proper alignment. position each hasp centrally over the padbolt
proper alignment. position each hasp centrally over the padbolt shaft, and secure with screws. The sheet metal shaft, and secure with screws. The sheet metal
screws supplied have the ability to self drill through the chanscrews supplied have the ability to self drill through the channel, use a continuous firm pressure and high drillnel, use a continuous firm pressure and high drill
speed and the screws will penetrate the sheet metal. If necessaspeed and the screws will penetrate the sheet metal. If necessary a 3mm drill bit can be used.ry a 3mm drill bit can be used (1/8")
padbolt shaft and drill 1/8” holes and secure with screws.

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 18 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
PAGE 18
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14
Premier Garden Shed -
Model: J30302G
PANEL CONSTRUCTION
NOTE: Take care to ensure that both front
and rear wall panels are not positioned
upside down. The top channel of each
panel is pre-punched for attaching roof
sheets, the bottom channels
are not.
SIDE WALL PANEL
CHANNELS FIT INTO THE
NOTCHED FRONT AND
REAR WALL PANEL
CHANNELS CHANNEL TYPE 60A
THIS END
CHANNEL TYPE
81A THIS END
97A
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 19 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
SLIDE THE ROOF PANEL INTO
POSITION, AND SECURE WITH
ONE SCREW AT EACH CORNER
ONLY AT THIS STAGE
SECURE PEAK
BRACE TO RIDGE
BEAM AND ROOF
PANEL WITH ONE
SCREW AT EACH
END
MOVE THE OTHER
ROOF PANEL INTO
POSITION AND SECURE
PEAK BRACE TO RIDGE
BEAM AND ROOF
PANEL WITH ONE
SCREW AT EACH END
ROOF CONSTRUCTION
PAGE 19
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14
Premier Garden Shed -
Model: J30302G
INSIDE VIEW OF FIXING
INSTRUCTIONAL
VIDEOS

ASSEMBLY INSTRUCTION - MODEL: 30302GK-PTXABSCO INDUSTRIES PAGE 20 23/09/19
ABSCO PREMIER SHED
MODEL: 30302GK-PTX
10’ W x 10’ D x 7’ H Australian Made
DYNABOLT
BOLT & NUT
STEEL
ANGLE
SLAB
WALL
SHEET
FINAL CONSTRUCTION
BEND THE TOP AND
BOTTOM FLANGES AS
SHOWN, THEN HOOK THE
BOTTOM FLANGES UNDER
THE TOP CHANNEL AND
SCREW THE TOP FLANGES
FOR BOTH AS SHOWN
GABLE CAPS
PAGE 20
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30302G 26/02/14
14A
Premier Garden Shed -
Model: J30302G
ANCHORING OF SHED
LOCATION OF 12
CONCRETE ANCHORS
- EACH ANCHOR CONSISTS OF ONE NUT, BOLT,
DYNABOLT AND STEEL ANGLE
- DRILL A 25/64" HOLE INTO THE WALL SHEET
- DRILL A 25/64" HOLE INTO THE CONCRETE
INSTRUCTIONAL
VIDEOS