ABSCO SHEDS 30152GK-PTX User manual

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 1 27/07/22
5’ 4”
10’ 2”
CONCRETE SLAB
4”
+
We highly recommend downloading the Absco Sheds
Assembly App to assist with your build.
ASSEMBLY APP AVAILABLE ON
Scan to
download
STEP BY STEP ASSEMBLY VIDEOS • PARTS CHECKLISTS • FAQ • 7 DAY
CUSTOMER SERVICE • WARRANTY INFORMATION • COUNCIL FORMS
AU: 1800 029 701
N Z: 0800 466 444
[email protected]
www.abscosheds.com.au
[phone] [email protected]
www.abscogardensheds.com
[phone] PLEASE LEAVE A REVIEW
www.abscosheds.com.au/review
When laying a concrete slab for your shed, it is
best practise to have a rebated edge to prevent
water ingress.
Rebated section is 1” high and inset 3” on all sides
from the overall slab base dimensions
Overall slab base
dimensions for this
model are as shown
above.
Illustration not to
scale.
1”
3”
RAISED FLOOR
INSIDE SHED
4”
3”
WALLS SIT
ON THIS LEVEL

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 2 27/07/22
2 - 3 people Approx. 6 hours
6
NUMBER OF HOURS REQUIRED
ASSEMBLY DIFFICULTY
NUMBER OF PEOPLE REQUIRED
Basic Complex
TOOLS REQUIRED
RECOMMENDED
Personal protective
equipment for tools
Hand
Protection
Enclosed
Shoes
Raised work surface. EG
Sawhorses and timbers
Heavy and/or bulky. Multi-
person lift or mechanical aid.
5/16” Hex driver bit
Ladder Hammer drill Shifter
metal & masonry drill bits
to suit anchor fasteners
Pop riveterTinsnipsCordless drill
GENERAL INSTRUCTIONS
• Before commencing any assembly, read
through these instructions in detail to gain
a thorough understanding of assembly
methods and associated details.
• Unpack the carton and carefully identify
and check off all the parts against the
parts described and illustrated on
"COMPONENTS PACKING LIST" pages.
SITE PREPARATION
• The site for the shed must be level. An
uneven surface may result in misalignment
of parts.
• The shed shall be erected on top of a
reinforced concrete slab and anchored
down appropriately illustrated on “FINAL
CONSTRUCTION” page.
SAFETY NOTES
• Some parts may have sharp edges. It is
advisable to wear gloves when handling these
items and safety glasses if drilling holes.
Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored
to a solid foundation immediately after
construction is completed.
• It is highly recommended to erect the shed
with two or more people.
• Do not sit, stand or walk on the roof of your
shed.

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 3 27/07/22
COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS
PAGE 3
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS
30A
2
31A
2
36L
2
36R
2
15A
2PEAK BRACE
58C
4CHANNEL
2CHANNEL 82L
2CHANNEL 81E
58B
1CHANNEL
58A
2CHANNEL WITH HINGES
79A
1CHANNEL
COMPONENT
DESCRIPTION PART
No. CHECK COMPONENT
DESCRIPTION PART
No. CHECK
QTY QTY
34A
2
A
1
52A
8
B
1
2CHANNEL 82R
82R
82L
79A
81E
58C
58B
58A
STEEL SHEET
5' 10 9⁄32" Long
2' 6 7⁄16" Wide
STEEL SHEET
5' 10 9⁄32" Long
2' 6 7⁄16" Wide
STEEL SHEET
5' 7 29⁄32" Long
2' 6 7⁄16" Wide
STEEL SHEET
5' 7 29⁄32" Long
2' 6 7⁄16" Wide
STEEL SHEET
5' 10 9⁄32" Long
2' 3 63⁄64" Wide
STEEL SHEET
6' 3 25⁄64" Long
2' 6 7⁄16" Wide
STEEL SHEET
2' 7 5⁄16" Long
2' 6 7⁄16" Wide
STEEL SHEET
6' 3 25⁄64" Long
2' 6 7⁄16" Wide
L = 5' 7 29⁄32"
L = 5' 7 29⁄32"
L = 2' 6 7⁄16"
L = 5' 1 47⁄64"
L = 4' 11 9/16"
L = 2' 6 3/16"
L = 2' 6 3/16"

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 4 27/07/22
55BL
1CHANNEL
81BL
1CHANNEL
81AL
2CHANNEL
60AL
2CHANNEL
97AL
1RIDGE
BEAM
55AL
1CHANNEL
55CL
1CHANNEL
81B
55A
55C
55B
60A
81A
COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS
PAGE 4
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS
COMPONENT
DESCRIPTION PART
No. CHECK COMPONENT
DESCRIPTION PART
No. CHECK
QTY QTY
55BR
1CHANNEL
81BR
1CHANNEL
81AR
2CHANNEL
60AR
2CHANNEL
97AR
1RIDGE
BEAM
55AR
1CHANNEL
55CR
1CHANNEL
81B
55A
55C
55B
60A
81A
CSJ
8ZARSP
THESE COMPONENTS ARE TO BE
JOINED TO THESE COMPONENTS
1
CHANNEL JOINER RIDGE BEAM JOINER
L= 1' 5 23⁄32"
L= 7 7⁄8"
L = 4' 10 59⁄64" L = 4' 10 59⁄64"
L = 4' 10 59⁄64"
L = 4' 10 59⁄64"
L = 4' 10 59⁄64"
L = 3' 811⁄32"
L = 4' 10 59⁄64"
L = 4' 10 59⁄64"
L = 4' 10 59⁄64"
L = 4' 10 59⁄64"
L = 4' 10 59⁄64"
L = 3' 811⁄32"
L = 4' 11 7⁄8" L = 4' 11 7⁄8"

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 5 27/07/22
PAGE 5
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS
14A
2CAP GABLE
L: 6 11/16"
12 11/64” CSK SCREW &
NUT SECURE HINGES
TO DOOR
(ALTERNATE METHOD)
85/32” NUT & BOLT SET
SECURE TWO
PADBOLTS TO DOOR
SHEET
220 SELF TAPPING
SCREWS
3DOOR
PADBOLT 2DOOR
PADBOLT
HASP
12 POP RIVETS SECURE
HINGES TO DOOR
1
COMPONENT
DESCRIPTION PART
No. CHECK COMPONENT
DESCRIPTION PART
No. CHECK
QTY QTY
CONTENTS OF FITTINGS PACKET
COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS
12A
2DOOR
STRAP
L: 6 1/2"
22A
90A
JAMB L= 5' 1 3/4"
1
91A
JAMB L= 3' 8 1/8"
4
85A
LIP TRIM L= 2' 7 5/16"
4
89C
JAMB L= 5' 7 15/16"
1
89A
JAMB L= 5' 10 1/4"
2Part No. Here
Part No. Here
Part No. Here
Part No. Here
85A
8SELF DRILLING HEX
HEAD TEK SCREWS (NO
HOLE REQUIRED) 1/8" DRILL BIT
HEX TEK SCREW
DRIVER BIT
1
1
RIVET GUN

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 6 27/07/22
20mm 15mm
QTY = 10pcs.
CHANNEL
(0.79") (0.59")
PUSH PUSH
CHANNEL
CSJ
PAGE 6
INSTRUCTIONS FOR JOINING SPLICED CHANNELS
CSJ
CSJ
HIGH-SIDE
CHANNEL
LOW-SIDE
CHANNEL
CSJ
CSJ
CSJ
= =
= =
==
=
=
STEP 1.
Position the channels and the CSJ
joiner channel so the center of the
CSJ is in line with the end of each
channel to be joined together.
STEP 2.
Join the first channel to the CSJ by inserting the center
of the CSJ (on an angle) to the end of the channel
where the JOIN>> text is marked. Push down one side
of the CSJ until you hear a 'click'.
STEP 3.
Join the second channel to the CSJ
by positioning the <<JOIN end of the
channel at the center of the CSJ
(on an angle). Push the CSJ into
the channel until you here a 'click'.
=
The joined channels should now
look like the picture above with the
CSJ positioned equally inside of the
joined channels.
FINISHED CHANNEL
=
NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER.
JOIN>> <<JOIN JOIN>>
JOIN>> SJ
JOIN>>
<<JOIN
JOIN>> <<JOIN
J
CSJ
DRILL 4mm (0.16") x 3mm (0.12")
(2 PER A SIDE) HOLES TO
SECURE SECTIONS TOGETHER.
(THESE SCREWS MAY HAVE TO
BE TEMPORARILY REMOVED
AND REPLACED DURING LATER
ASSEMBLY)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 7 27/07/22
PAGE 7
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
=
=
=
=
=
=
2 X 60AR
9' 9 13/16"
STEP 1. PRE-ASSEMBLY OF SPLICED CHANNELS
2 x 81A
2 x 60A
1 x 55A
1 x 55C
1 x 55B
1 x 81B
NOTE: JOIN TOGETHER 16 X CHANNEL SECTIONS USING 8 X CHANNEL JOINERS (PART CSJ)
81BR
81BL
55BL
55BR
55CR
55CL
55AL
55AR
60AR
60AL
81AL
81AR
2 X 81AR
2 X 81AL
2 X 60AL
1 X 55AR
1 X 55AL
1 X 55CR
1 X 55CL
1 X 55BR
1 X 55BL
1 X 81BR
1 X 81BL
NOTE: SOME CHANNELS HAVE
HOLES IN THEM - YOU WILL NEED
TO RE-DRILL HOLES ON ANY
CHANNEL WHERE THE CSJ
JOINING CHANNEL COVERS
HOLES ON THE CHANNELS
YOU ARE CONNECTING
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS
IMPORTANT:
SOME CHANNELS HAVE

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 8 27/07/22
PAGE 9
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
TEK SCREW DRIVER BIT
QTY. = 1
QTY. = 8
QTY. = 2
QTY. = 1
SELF DRILLING TEK SCREW
PART ZARSP - 1' 5 11/16" LONG
ZARSP
RIDGE BEAM 4' 11 7/8"
PARTS 97AL & 97AR
STEP 2. PRE-ASSEMBLY OF SPLICED RIDGE BEAM
PUSH PUSH
97AL
97AR
5/8"
7 7/8"
9 13/16"
9' 9 13/16" OVERALL LENGTH
(PART 97A)
5/8"
THE TOP SECTIONS OF
CAPPING WILL OVERLAP
EACH OTHER AT THE
JOIN BY 2”.
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 9 27/07/22
PAGE 8
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: J30232G 26/02/14
STAGE 1: PUSH RIDGE BEAMS TOGETHER, MAKE SURE THERE IS A 2" OVERLAP
OF THE RIDGE CAP
STAGE 2: INSERT RIDGE CAP JOINER INTO CONNECTED RIDGE CAPS.
MAKE SURE JOINER HAS 8 55/64" IN EACH RIDGE CAP.
STAGE 3: TURN RIDGE CAP OVER AND MEASURE 9 27⁄32" FROM THE END
OF EACH RIDGE CAP.
PLACE TEK SCREWS IN 2" INCREMENTS FROM SAID END.
REPEAT THIS PROCESS FOR THE OPPOSING HALF OF RIDGE BEAM
INSTRUCTIONS FOR JOINING SPLICED RIDGE BEAM
2"
8 55⁄64"
2"
2"
Premier Garden Shed - Model: J30232G
INSTRUCTIONAL
VIDEOS

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 10 27/07/22
Premier Garden Shed - Model: 30152GK
85A
60A
14A
85A
81A
85A
85A
VIEW OF ROOF COMPONENTS
14A 81A
97A
52A
52A
52A
52A
NO.
PAGE 10
ABSCO INDUSTRIES
ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
52A
52A
52A
52A
INSTRUCTIONS
AND VIDEOS

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 11 27/07/22
VIEW OF WALL COMPONENTS
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
Premier Garden Shed
Model: 30152GK
36L
36R
82R
31A
30A
31A
30A 36R
36L
34A
34A
A
B
22A
81E
81B
55B
15A
82R
82L
55A
82L
55C
91A
81E
90A
91A
89A
89A
79A
PAGE 11
INSTRUCTIONS
AND VIDEOS

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 12 27/07/22
PAGE 12
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS
ABSCO ASSEMBLY INTRODUCTION
FASTENING SYMBOLS
The snaptite assembly system locks most perimeter channels to all roof and wall
sheets without the need for tools and fasteners.
To pre-assemble the four wall panels
and two roof panels, the perimeter
channels are secured to the top and
bottom of each panel using the
snaptite system, as detailed on the
following pages wherever you see
the symbol.
Position sheets on timbers,
trestles or partly over edge of
concrete slab.
Each perimeter channel must finish flush with the
edges of the sheets.The snaptite system allows
adjustment for this process by simply tapping the
channel along the sheets until each end is neatly
flush. If you need to remove channels from the
panels, pull the channel along the panel from
opposing ends. You may need someone to help
with this.
Join components together with one screw at this
location only, as some channel sections have extra
holes that are not required for this model of garden
shed
Do not join components together at this location yet,
as the screw may obstruct further assembly of other
components
4mm NUT & BOLT SET
3mm POP RIVETS
PUSH
PUSH
HIGH SIDE
HIGH SIDE
PUSH
HIGH SIDE
HIGH SIDE
After joining sheets together, position channel over one end of the sheets, gently
tapping it over the snaptite lugs, working along the sheets to the other end.
HIGH SIDE
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
Join components together by pre-drilling the holes
first. Use one component as a template to mark where
the holes are. Drill with 3mm drill bit.
D

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 13 27/07/22
Part numbers are found on
the inside of the sheeting
near the corner.
Shown as grey box on left
1. Overlap specified sheets as
shown. Make sure ends are flush.
Where possible, have sheets
orientated so printed part
numbers are as shown.
edge holes to outside
edge holes to outside
2. Fasten with self tapping
screws through prepunched
sheet-to-sheet holes on overlap.
If you can’t see bottom hole twist
the sheet left or right.
Make a new hole with supplied
drill bit if bottom hole is too far
up or down the sheet or not
found.
3. Attach the top and bottom
channels using the SNAP-TiTE
method.
Make sure you have the short
side of the channel to the
outside of the sheeting
31A
31A
30A
30A
81B
55B
REAR PANEL
ASSEMBLY
START HERE

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 14 27/07/22
START HERE
ROOF PANEL ASSEMBLY
2 completed panels are required.
60A
81A
SNAP
T TE
i
SNAP
T TE
i
85A
85A
52A
52A
52A
52A
Fit 81A channel to
edge of sheet with
these holes.
This is the edge
that will be screwed
down on top of
the wall in the final
stage.
Orientate all sheets
so the short ends
with the holes are
on the same side
and are lined up.
Edge for ridge beam
Edge with holes for wall

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 15 27/07/22
START HERE
SIDE PANEL ASSEMBLY
2 completed panels are required.
Trim the tip of each sheet to
allow channels to fit hard up
to the edge of the sheet.
36L
36R
82R
81E
15A
82L
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
Overlap both sheets as shown.
Make bottom edges flush.

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 16 27/07/22
4. FRONT PANEL ASSEMBLY
PAGE 15
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS
89A
89A
55A
90A
79A
55C
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
34A
34A
55A
90A
89A
55A
55A
55A
55C
89A
90A
89A
79A
55C
89A
79A
START HERE
FRONT PANEL ASSEMBLY

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 17 27/07/22
PAGE 16
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS
DOOR PANEL ASSEMBLY
13/16”
58C
58C
FOUR HOLE SET
FOR PADBOLT
CONNECTION
58C
12A
58C
58A
58A
9/16” FLANGE
A
B
89C
58B
A
B
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
ALL VERTICAL DOOR CHANNELS
ARE INSTALLED IN THE REVERSE
DIRECTION IN COMPARISON TO
HORIZONTAL DOOR CHANNELS
FLANGE
5.
START HERE
DOOR PANEL ASSEMBLY

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 18 27/07/22
DOOR PANEL ASSEMBLY
NOTE: Nuts and bolts (supplied) may be
used instead of pop rivets (supplied) by
simply enlarging the hinge hole sets in the
jamb using a 5/32" drill bit
PAGE 17
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
91A
91A
A
B
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS
NOTE: The two holes required to connect the padbolt hasp for ea
NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for ch door have not been pre-punched, to allow for
proper alignment. position each hasp centrally over the padbolt
proper alignment. position each hasp centrally over the padbolt shaft, and secure with screws. The sheet metal shaft, and secure with screws. The sheet metal
screws supplied have the ability to self drill through the chanscrews supplied have the ability to self drill through the channel, use a continuous firm pressure and high drillnel, use a continuous firm pressure and high drill
speed and the screws will penetrate the sheet metal. If necessaspeed and the screws will penetrate the sheet metal. If necessary a 3mm drill bit can be used.ry a 3mm drill bit can be used (1/8")
padbolt shaft and drill 1/8” holes and secure with screws.
Flip the door panel over and attach
the 91A braces to the inside, screw
up from beneath.

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 19 27/07/22
Side wall channels
fit into the
notched rear wall
channels.
PANEL CONSTRUCTION
NOTE: Take care to ensure that all wall panels
are not upside down. The top channels
of each panel are pre-punched for
attaching roof sheeting.
Suggested
assembly order
- Front
- Sides
- Rear
Next, prepare a single roof panel as shown.
Slide ridge beam down onto roof panel. Align
shared holes and secure the panel with self
tapping screws from underside
Make sure roof panel is
orientated with holes for the
wall away from ridge beam
Roof panel channel should be
flush with end of ridge beam
Roof panel with ridge beam
ready for assembly.
Ridge beam
Roof panel underside

ABSCO PREMIER SHED
MODEL: 30152GK-PTX
10’ W x 5’ D x 6.5’ H Australian Made
ASSEMBLY INSTRUCTION - MODEL: 30152GK-PTXABSCO INDUSTRIES PAGE 20 27/07/22
SLIDE THE ROOF PANEL INTO
POSITION, AND SECURE WITH
ONE SCREW AT EACH CORNER
ONLY AT THIS STAGE
SECURE PEAK
BRACE TO RIDGE
BEAM AND ROOF
PANEL WITH ONE
SCREW AT EACH
END
MOVE THE OTHER
ROOF PANEL INTO
POSITION AND SECURE
PEAK BRACE TO RIDGE
BEAM AND ROOF
PANEL WITH ONE
SCREW AT EACH END
8. ROOF CONSTRUCTION
PAGE 19
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30152GK 13/04/16
Premier Garden Shed
Model: 30152GK INSTRUCTIONS
AND VIDEOS
INSIDE VIEW OF FIXING