ABSCO SHEDS Premier 23231GK User manual

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23231GK
2.26mW x 2.26mD x 2.00mH
Model: 23231GK 06/09/18 1.2 1
Download the Absco
Sheds Assembly App
for instructional videos
MANU FA CT URED
IN A US TR ALIA
SNAPTiTE
Assemb ly
AU: 1800 029 701
N Z: 0800 466 444
[email protected]
www.abscosheds.com.au
When laying concrete slab, ensure there
is a rebated edge 25mm deep around the
perimeter. This will help water egress from
the base of the shed.
For construction in non-cyclonic areas
Wind rating: N2 as per AS4055-2012
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: 23151GK 21-11-2017
CONCRETE SLAB
2360mm
1620mm
FRONT: 2.26m
SIDE: 1.52m
HEIGHT: 1.95m
We thank you for choosing an Australian made
shed. For further assistance please visit our detailed
instructional video library at
Http://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be
number ONE, so please let us know what you think
of our instructions. Feedback makes us better.
[email protected]
CONCRETE
REBATED EDGE
BOTTOM CHANNEL
CONCRETE SLAB
75mm WIDE REBATE
100mm
WHEN LAYING YOUR CONCRETE
SLAB, ENSURE THERE IS A
REBATED EDGE 25mm DEEP
AROUND THE PERIMETER
THIS WILL HELP WATER EGRESS
FROM THE BASE OF THE SHED
Absco Industries
Premier Shed Model: 23151GK
PAGE 01
CONCRETE SLAB
2360mm
2360mm

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23231GK
2.26mW x 2.26mD x 2.00mH
Model: 23231GK 06/09/18 1.2 2
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough
understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described
and illustrated on "COMPONENTS PACKING LIST" pages.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately
illustrated on “FINAL CONSTRUCTION” page.
TOOLS REQUIRED
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and
safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored to a solid foundation immediately after construction is
completed.
• It is highly recommended to erect the shed with two or more people.
RECOMMENDED
3mm drill bit 10mm drill bit metal/masonry

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23231GK
2.26mW x 2.26mD x 2.00mH
Model: 23231GK 06/09/18 1.2 3
COMPONENT PACKING LIST
Check off all components.
2
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT DESCRIPTION
PART
No. CHECK
QTY QTY
2
1
2
2
2
6
2
1
STEEL SHEET
1785mm X 773mm 31A
1785mm X 773mm 30A
STEEL SHEET
STEEL SHEET
1915mm X 773mm 36L
STEEL SHEET
1915mm X 773mm 36R
STEEL SHEET
1785mm X 731mm 32A
STEEL SHEET
1725mm X 773mm B
15A
PEAK BRACE
2
STEEL SHEET
1980mm X 773mm 42D
STEEL SHEET
1170mm X 773mm 49A
CHANNEL
L = 1143mm
83R
97BL
1
ZARSP
RIDGE
BEAM
1
1
L = 1152mm (45.3")
RIDGE BEAM JOINER
L: 450mm (17.7")
97BR
RIDGE
BEAM
L = 1152mm (45.3")

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23231GK
2.26mW x 2.26mD x 2.00mH
Model: 23231GK 06/09/18 1.2 4
COMPONENT PACKING LIST
2
11
1
11
79B
CHANNEL
L = 788mm
58B
CHANNEL
L = 1725mm
58A
CHANNEL WITH HINGES
L = 1725mm
58C
CHANNEL
L = 773mm
89A
JAMB L= 1785mm
89B
JAMB L= 1785mm
90B
JAMB L= 788mm
1CHANNEL
L = 1143mm
83L
2
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT DESCRIPTION
PART
No. CHECK
QTY
54AL
54CL
54BL
81DL
81CL
60BL
QTY
54CR
1
1
1
1
4
2
1
1
1
1
4
2
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1126.5 (44.3")
54BR
81DR
81CR
60BR
54AR
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1126.5 (44.3")
CHANNEL
L = 1126.5 (44.3")

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23231GK
2.26mW x 2.26mD x 2.00mH
Model: 23231GK 06/09/18 1.2 5
COMPONENT PACKING LIST
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY QTY
1
2
1
91A
JAMB L= 1120mm
12A
DOOR
STRAP
L: 165mm
14A
CAP GABLE
L: 170mm
ASSEMBLY
INSTRUCTIONS
86A
LIP TRIM L= 1170mm
CSJ
10 CHANNEL JOINER
L= 200mm (7.9")
INSTRUCTIONS & FITTINGS PACKET
DOOR
PADBOLT
HASP
1
1
SELF TAPPING SCREWS
PACKET CONTAINING 220
1
DOOR
PADBOLT
FAST006
3/16 COUNTERSUNK
SCREWS & NUTS
63.2 x 8mm
BLIND POP RIVETS
6
PSTKSGL - SINGLE DOOR FITTINGS PACK
PACK 6P - SCREW PACK 6
PACK 6P
SCREW PACK 6
1
PHILLIPS DRIVER BIT
3mm DRILL BIT DRILL
FAST007
FAST038
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT DESCRIPTION
PART
No. CHECK
QTY QTY
10 16mm TEK
SCREWS FAST014
2
1 1
4
1
1
SELF TAPPING SCREWS
PACKET CONTAINING 100
PSTKSGL
SINGLE DOOR FITTINGS PACK

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23231GK
2.26mW x 2.26mD x 2.00mH
Model: 23231GK 06/09/18 1.2 6
SNAPTiTE ASSEMBLY GUIDE
The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for
tools and fasteners.
To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.
Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet.
Each perimeter channel must finish flush with the edges of the sheets. Simply tap the channel along
the sheets until each end is neatly flush. If you need to remove channels from the panels, slide it off
from the side.
Channel locks the shed panel into
position without the need for screws!
FASTENING SYMBOLS
Secure channel to sheeting by SNAPTiTE
fastening method.
Join components together with one
screw at this location only, as some
channels have extra holes that are not
required for this model of shed.
Do not join components together at
this location yet, as the screws may
obstruct further assembly of the other
components.
Join components together by pre-drill-
ing the holes first. Use one component as
template to mark where the holes are and
drill with a 3mm drill bit.
3mm pop rivet
4mm nut and bolt set.
D
SNAP
T TE
i

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23231GK
2.26mW x 2.26mD x 2.00mH
Model: 23231GK 06/09/18 1.2 7
Guide on Joining Spliced Channels
The text marked on all parts must be shown on the same side as each other
Step 1.
Position the channels and the
CSJ joiner so the centre of
the CSJ is in line with the end
of each channel to be joiner
together.
Step 2.
Join the first channel to the CSJ
by inserting the centre of the
CSJ, on an angle, to the end of
the channel where the JOIN>>
text is marked.
Push down one side of the CSJ
until you hear a ‘click’.
Step 3.
Join the second channel to the
CSJ by positioning the <<JOIN
of the channel at the centre of
the CSJ, on an angle. Push the
CSJ into the channel until you
hear a ‘click’.
Finished Channel.
The joined channels should
now look like the picture with
the CSJ positioned equally
inside of the joined channels.
Drill out holes with 3mm drill
bit in CSJ to match the holes
in channel and secure with the
screws supplied.
These may have to be
temporarily removed during
assembly.
= =
JOIN>> <<JOIN
CSJ
==
JOIN>>
J
==
JOIN>> SJ
= =
JOIN>>
<<JOIN
= =
JOIN>> <<JOIN
Finished Spliced
Channel
Channel
Push
20mm 15mm
CSJ
.
...

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23231GK
2.26mW x 2.26mD x 2.00mH
Model: 23231GK 06/09/18 1.2 8
PRE-ASSEMBLY OF SPLICED CHANNELS
NOTE: Some channels may have holes in them - You will
need to redrill holes where CSJ joining channel covers
them.
Join together 20 x channel sections using 10 x channel joiners (Part CSJ)
=
=
=
=
=
4 X 81CR
2253mm
2 x 60B
4 x 81C
1 x 54A
1 x 54B
1 x 54C
81CL
81CR
60BR
60BL
2 X 60BR
2 X 60BL
4 X 81CL
1 X 54AR
1 X 54AL
1 X 54BR
1 X 54BL
1 X 54CR
1 X 54CL
54CR
54BR
54AR
54CL
54BL
54AL
=2 x 81D
2 X 81DR
2 X 81DL
81DR
81DL

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23231GK
2.26mW x 2.26mD x 2.00mH
Model: 23231GK 06/09/18 1.2 9
Tek screw driver bit
Push
Guide on Joining a Spliced Ridge Beam
Follow these three steps to assemble a ridge beam.
Step 1.
Place two ridge beams as
shown and push them together.
Slide the cap of one under the
other.
NOTE.
There is a 50mm overlap of the
ridge caps when the beams are
in position.
Step 2.
Use the ZARSP to connect at
the centre of the two ridge
beams. Be sure it is pushed in
fully.
Step 3.
Turn over the ridge beam.
Measure 250mm from the
middle along the centre of one
ridge beam, mark spacings of
50mm. Fasten with a Tek screw
at each marking.
Repeat to the other side of the
ridge beam assembly.
TIP: Predrilling each hole with
the 3mm drill bit makes it easier
to fasten.
50mm
225mm
ZARSP
Finished Spliced Ridge Beam
Finished
Spliced Ridge Beam
ZARSP
Ridge Beam
Self drilling Tek screw

Absco Industries Assembly Instruction Manual
ABSCO PREMIER SHED
MODEL: 23231GK
2.26mW x 2.26mD x 2.00mH
Model: 23231GK 06/09/18 1.2 10
PRE-ASSEMBLY OF SPLICED RIDGE BEAM
.
.
1x 97BL
1x 97BR
= 1x 97B
2253mm Overall length
ZARSP
225mm
97BL 97BR
16mm
16mm