Access Lighting 20347 User manual

IMPORTANT
Before assembling your access lighting fixture, please make sure that
you carefully read through these instruction sheets. Consider having
your fixture installed by a qualified licensed electrician.
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations
that may occur. It must be understood that common sense, caution and
care, are factors that can’t be built into any product. These factors must
be supplied by the person(s) caring for and operating the fixture.
STEP BY STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
light off at the light switch is not sufficient to prevent electrical shock.
MARK BACK PLATE LOCATION
Determine the desired location of your fixture. Hold
the back plate up to the surface and mark with a pencil
the location of the mounting plugs (small hole on
the up and down side of the back plate). Drill
a hole and insert the mounting plugs into the mounting
surface.
1
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and National Electrical Codes. These fixtures are intended for
mounting to a standard 4” x 2 1/2”metal octagon outlet box. The box
must be directly supported by the building structure and U.L. Recognized.
WHAT YOU NEED
•
Screwdriver
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
INSTALLATION INSTRUCTIONS
WHAT WE PROVIDE
•
Back Plate
• Mounting Hardware
• Gasket
• 1 x Crossbar
• 1 x Glass diffuser
• 1 x Front Cover
• 2 x 24W T5 HO Tubes
COLLECTION
1
CERTIFICATION: CETL WET NO. 20347
20347
APPLICATION MODEL NO.
Wall Fixture

2
4
2
CERTIFICATION: CETL WET NO. 20347
3
MOUNT CROSSBAR
If there is an existing fixture remove it.
Mount the crossbar with bracket to the J-box
with the supplied screws. Make sure that the additional
ADD THE GASKET
Fit the supplied Gasket onto behind the Back plate.
MAKE WIRE CONNECTIONS
Gently pull the supply wires through the hole in the
crossbar . Gently feed the fixture wire through one
of the slits in the back plate and then through the hole
floating canopy. Connect the black supply
wire to the black fixture wire. Secure with the supplied
wire nuts. Connect the white supply wires to the white
fixture wire. Secure with the supplied wire nuts. Either
wrap the green wire around one of the protruding screws
or connect it to the supply ground wire. Secure all wire
with electrical tape (not supplied).
Tuck all wires carefully into the J-Box.
.

3
CERTIFICATION: CETL WET NO. 20347
5
6
MOUNT THE BACK PLATE
Feed the nipple from the crossbar through the
designated hole in the back plate. Use the supplied
thumb nut to secure the nipple to the back plate. Hold
the back plate up to the mounting surface, insert the
supplied screws in the mounting plugs and secure the
back plate to the mounting surface.
INSERT TUBE
Insert the Tubes.
MAXIMUM WATTAGE 24W.
DO NOT EXCEED THE WATTAGE AS STATED
ON THE WARNING LABEL AND IN THE INSTRUCTION
SHEETS
SECURE THE GLASS DIFFUSER
Position the glass diffuser over the back plate.
Align the holes at the left and right of the plates.
Secure with the supplied allen screws and
L-type screw driver.
7

8
4
CERTIFICATION: CETL WET NO. 20347
9
SECURE THE FRONT COVER
Position the front cover over the glass diffuser.
Align the holes at the left and right of the plates.
Secure with the supplied screws.
.
Please ensure that the fitting is cool and
switched off before replacing the bulb.
DO NOT use bulbs that might exceed the
maximum wattage, stated on caution label.
CAUTION
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF YOUR
NEW ACCESS FIXTURE