AccessPRO TVPRO400 User manual

KCV-434SD/ KCV-D434SD
MANUAL
Hands-Free Video Door Phone
• Slim and compact design
• 4.3” digital LCD color monitor
• Icon buttons
• OSD function
• Communication with visitor and door aperture
•Contact button
•Lobby opertion with the guard
TVPRO400
MANUAL TVPRO400
[Installation and Operation Manual]
TVFPRO20TVPRO400MW TVPRO400MB
Monitor
Camera

2
Installation Location
•Monitor Installation
· The standard installation of the monitor
is at an approximate height of 1.5 meters,
from the center of the monitor at eye level.
In this case, center the metal base on the
wall (centering the wiring pipe) at 1.45
meters from the ground level.
· Standard installation height.
•Things to consider for camera installation
· Avoid installing the camera by exposing it directly to the rays of light (and the Sun)
· Be careful of the backlight and obscuration of visitors' faces, which makes
identification difficult.
· Avoid installing the camera in places like in the following Images.
(1) Places lit by natural light as background
(3) Places with direct rays of light
(2) Places with white wall reflecting direct rays of light.
•Camera Installation
· The standard camera installation is at
a height when the lens is approximately
1.4 meters from the floor level. In this ca-
se, the chamber is centered (with the pipe
box) at approximately 1.39 meters from
the ground level.
Lens center Lens Center
Lower section
of the box
•Monitor installation
•Directly connect the power cable to the power cable
1) Do not do electrical work yourself. The installation of the product in this case requires
the dependence of an electric licensed or certified electrical work.
2) Insulate with electrical tape while cutting the power cord and connect the power cord
so that the power cord is not exposed to the metal. The contact between the electric
cables can cause fire or electric shock accidents.
3) The connection will require electrical work after intercepting the power supply.
1) Remove the metal wall bracket behind the monitor.
2) Install the metal wall bracket in a type 1 box or on the wall.
3) Connect the terminal wiring behind the monitor referenced in the product connection diagram.
4) Hang the monitor on the metal wall bracket, and fix the monitor on the supplied bracket.
After fixing the bracket with 4 screws, place the
camera inside the holes behind the bracket.
Then fix with the screws.
5) Connect the monitor power cable and see if the power switch is on [ON] on the side of the monitor.
•Camera Installation
[TVFPRO20]
Wall Screw
(2X8mm)
Main body support
Screw
(3X5mm)
•

Product Components
•Camera
[TVFPRO20]
Main body
Screws to x the camera
Screws to x the camera
support
or 3X5mm
2X8mm
3
•Cable
•Wall frame
Screws for monitor instalaltion
4-pin cable for the
camera 1ea
•
4X25mm 4ea
(at screw heads)
3X8mm 1ea
•Monitor
Camera cable - 4 polarized wires (VCC[12V]/GND/VOICE/VIDEO)
•
Monitor
Camera
AC 90V-AC 240V 50/60Hz
1W at standby, and 7.5W±20% at charge
0ºC ~ +40 ºC
4.3” color LCD display
Hands-free
Surface
Camera cable - 4 polarized wires (VCC[12V]/GND/VOICE/VIDEO)
140(W) x 195(H) x 32(D) mm
Model Number
Model Number TVFPRO20
TVPRO400MW / TVPRO400MB
Power Supply
Power Consumption
Operating Temperature
LCD
Communication System
Cable
Mounting Type
Dimensions
Power Supply
Consumption
Operating Temperature
Dimensions
Lens Angle
DC 12V±1V (Monitor Source)
Maximum 3W
-10 ºC ~ +50 ºC
40(W)x120(H)x22(D)mm
Diagonal 90˚
Specifications

4
Name & Functions of Each Part
•Monitor
•Camera
· Side
11
10
9
· Front
1
2
5678
3
4
· Back
12
13
⑨Call audio
⑩Volume switch
⑪Power ON switch
⑫Camera terminal
⑬AC CORD
①LCD Monitor
②Speaker
③Microphone
④Power supply LED
⑤Menu
⑥Guard
⑦Speak
⑧Open door
①Base Name
②GND
③Audio
④Video
⑤&⑥Door (no polarity)
⑦Camera Angle Knob
(Only KC-MC/MB30)
⑧Cable clamp
1
2
3
4
5
①C-Mic: for communication with the monitor
②Camera lens
③LED
④Call button: Press the home button to call
⑤Speaker : When the visitor call the monitors
audio will be send to this speaker.
· Front · Back

1
2
3
4
TOR
1
2
3
4
TOR
4 1
TOR
Camera
①
②
③
④
⑤
⑥
Naranja
Blanco / Naranja
① VCC
ambos
conductores
ambos
conductores
ambos
conductores
ambos
conductores
Verde
Blanco / Verde
② GND
Azul
Blanco / Azul
③ Audio
Café
Blanco / Café
④ Video
1. VCC
3.
EO
1
2
3
4
•
•
•
Name of each Connection Port
System configuration (Camera Mode)
System configuration (System Mode)
•Cable requirement - based on camera to monitor distance
•Camera cable connection •
Monitor cable connection
5
Product Connection Diagram
4-wire
Monitor
Door aperture
with external
power input
2-wire 4-wire
4-wire polarized
Camera
Monitor Monitor
Telephone reception
Due to some condition or the environment, the monitor may not automatically detect the NTSC or PAL signal.
In this case, turn off the monitor and turn it on again.
In Menu # 6. It is possible to set the PAL or NTSC signal manually.
- up to 100 meters: UTP5 cable
Guard’s telephone
4-wire
Distribuitor
Connect the monitor terminal to the camera
•
Connecting the monitor terminal to the camera
•
According to the outside environment, you may see the images not very clear.
However, this is not a result of a product defect or problem.
•
In case of more than 550 meters long of CAT5
CAT5 cable configuration
CAT5 cable configuration
cable, the display and voice quality may be lower.
issue. Less than 50 meters is recommended.
- Up to 50 meters 0.65 mm² cable
- Up to 100 meters 0.8 mm² cable
•
•
1
2
3
4
TOR
1
2
3
4
TOR
4 1
TOR
Cámara
①
②
③
④
⑤
⑥
Orange
White /Orange
① VCC
both
conductos
both
conductos
both
conductos
both
conductos
Green
White / Green
② GND
Blue
White / Blue
③ Audio
Brown
White / Brown
④ Video
1. VCC
3.
EO
1
2
3
4

6
Operation Instructions
While talking, press the [Door open] button and the door will be opened.
Aperture timer can be set from 1- 10 seconds
•Call Guard Master on System mode set
Set # 1 as SYSTEM
This function is for the master guard, KLP-C420, KVS-A4P or KVS-A8P.
Hold, press (Guard). When the guard gets up to
start talking.
(communication time: 3 minutes)
While speaking to the guard,
prss [Guard] to end the call
Instructions for operation
•
Camera Communication
•Open door
•Camera monitoring
Press the call button
A ringtone can be
heard from the device
Press the [talk] button when there is no image on the monitor
The image from the camera is shown on the screen.
(Monitoring time: 1-10 minutes)
You can hear a ringing
sound on all connected
monitors, and an image
will appear on the screen.
(waiting time: 30 seconds)
Press the [talk] button
and communicate with 1 camera
(communication time: 3 minutes)
Press the [talk] button to
end communication
H
e
l
l
o
H
o
l
a
H
o
l
a

7
Operation instructions
Instructions for operation
•
Sound adjustment
•Brigthness adjustment
Call adjustment: see on one side of the monitor and find the Vol button. It consists of 3 levels (high / medium / silent)
Receiver settings: While communicating, adjust the R. Vol button. It consists of 3 levels (high / medium / silent)
- talking, press [Menu] and a Brightness icon will appear.
At this point, adjust the brightness with the Up / Down / Enter keys
•Menu
1. MODE :
2. CAMARE : Select a camera
3. Display Time : Monitoring time 1 – 10 minutes
4. Door Time: Aperture time of 1-10 seconds / pressing
5. Language : Select language
6. SYNC : Image type selection
7. Initial : Software becomes default.
▶ CAMERA : in the case of a normal camera
▶ SYSTEM : for a guard or KLPC420
Menu
UP : Guard
DOWN : Talk
ENTER : Open Door
1. MODE : CAM
2. CAMERA : TVFPRO20
3. VIEW TIME : 1 Minute
4. DOOR TIME : 1 Sec
5. Language : ENGLISH
6. SYNC : AUTO
7. Initial : NO

Las especicaciones est án sujectas a cambio sin previo aviso.
O0516