TCS Carus Adapto User manual

3 years warranty
a brand of TCS AG
Design Manufaktur Adelheid
Adelheid 41
78098 Triberg
Germany
[email protected]
www.carus-concepts.com
Tel: [phone]
Fax: [phone]
- Art. no. 0035871 Version 1 A -

Instruction manual
Carus Adapto

Design
“A simple form, a classic layout and high-end materials gua-
rantee timeless aesthetics. The Carus edition refl ects the reli-
ability and sustainability of the products in perfect form and
sophisticated design. Our emphasis on traditional crafts that we
utilise to manufacture the high-quality surfaces, make the Carus
products unique items. The harmony between the traditional
and the modern element of our products enable us to design
customised and fi rst-class products which refl ect the user and
inspire emotions.“

Table of contents
02
03
03
04
05
06
07
8-11
12-13
14-17
Device overview
LED indication
Indication and operating elements
Setting the ring tone volume
Ring tone selection
Confi gurable functions
Cleaning
Operating the function keys 1 - 10
Labeling the function keys 1 - 10
Notes

2
Your brandnew indoor station!
CAI1100
Function key
Light switch button
Call OFF-button
Door release button
Speech button
Red LED 1
Green LED
Loudspeaker
Microphone
Ring tone volume Labeling fi eld
Function keys
Red LED 2

3
Indication and operating elementsLED indication
A ring tone signals an inco-
ming call.
The green LED is on.
Speaking
Shortly press the speech
button to accept the call
or longer than 1 second to
switch-over to simplex com-
munication during an active
voice connection.
The green LED is on.
Shortly press the speech
button again or the door
release button to end the
conversation (the call is ter-
minated after 4 seconds).
Automatic call cut-off after
2 minutes.
Door release
Shortly press the blue door
release button.
Switching lights
Shortly press the light switch
button.
Internal calls / Activate
additional functions
Press the function key to call
another indoor station or to
(de-)activate the call diver-
sion resp. the door release
automatic.
Confi guration necessary, see page 5.
Ring tone mute
Press the call OFF-button. In
case of an incoming call no
acoustic signal sounds.
The red LED is on.
• Green LED is on
• incoming door or
internal call
• active voice connection
• activated additional
functions
Confi gurable functions, see page 6.
• Red LED 1 is on
• Ring tone mute is acti-
vated, an incoming call
is signalled not acousti-
cally
• Red LED 1 blinks
• busy speech channel
• Red LED 2 is on
• incoming door call
• incoming internal call
• call diversion activated
• incoming control
function from sensor
• send alternately two
control functions with a
unique serial number
Function keys 1 - 10
Press one of these buttons
for a specifi c connection to
a front-door, specifi c internal
calling, indication of staus
information, call diversion,
sending a control function
or sending 2 control func-
tions alternately.
Confi guration necessary, see
page 8-11.
•
•
•
•

4
turn down turn up
With the contoller at the bottom of the device, the ring tone volume
can be adjusted continuously.
Setting the ring tone volume

5
Ring tones can be adju-
sted for four different call
types.
Thus, it is possilbe to
distinguish calls from
two different front-door
stations, a fl oor call or an
internal call.
You can choose between
13 different ring tones.
Proceed as follows:
1. Activate the ring tone
selection
End an eventually exisitng
conversation. Press the call
OFF-button for at least 8
seconds.
An acknowledgement
tone sounds.
2. Select a door ring tone
a... from the (fi rst)
front-door station
Press the door release
button until the desired
ring tone sounds.
The ring tone selected last
will be stored.
b ... from the second
front-door station*
Press the speech button
until the desired ring
tone sounds. The ring tone
selected last will be stored.
* If no seperate ring tone is selected, the
ring tone of the fi rst front-door station is
stored automatically.
c... from the fl oor door
Press the light switch button
until the desired ring
tone sounds. The ring tone
selected last will be stored.
Ring tone selection
d... from another indoor
station
Press the function key
until the desired ring tone
sounds. The ring tone se-
lected last will be stored.
3. Deactivate the ring tone
selection
To end the ring tone selec-
tion shortly press the call
OFF button once.
When no button is pressed
within the next 8 seconds,
the device ends the ring
tone selection automatically.
The ring tone selection ends
with an acoustic signal.

6
The following functions
can be confi gured on
your video indoor station
and for the use of further
indoor stations. Please
contact your qualifi ed
electrician.
Call an indoor station
(internal call)*
To call another indoor
station, press the function
key . A short acknow-
ledgement tone sounds if
the call has reached its call
destination. When the called
device accepts the call a
voice connection is establis-
hed. If required, the volume
of the voice connection can
be adjusted from a qualifi ed
electrician.
* max. 1 call destination
Door release automatic
An incoming door call
directly triggers the opening
of the door if this function is
activated. Press the function
key
activated,
the green LED is on,
press the function key
again
deactivated
Open the fl oor door
If the fl oor door call at the
fl oor door is triggered, the
fl oor door (instead of the
front-door) can be opened
with the door release button
within 30 seconds.
Parallel call
A second indoor station
sounds simultaneously in
case of an incoming door,
fl oor or internal call. the ring
tone sounds at both devices.
Call diversion
The incomning call is di-
verted to a second indoor
station. Press the function
key
activated,
the green LED is on,
press the function key
again
deactivated
Confi gurable functions

7
Cleaning
Clean the indoor station
with a dry or slightly wet
cloth. Remove stronger
stains with a PH-neutral
detergent.
Avoid water from entering
the device! Do not use any
abrasive detergents!

8
Function keys 1 - 10
The following functions can be programmed
(see page 9 - 11):
• specifi c door call / door release
• specifi c internal calls
• sensor functions / status indications
• activate / deactivate call diversion
• switching without feedback
• switching with feedback
To programme the required functions, please
contact your qualifi ed electrician.
Operating the function keys 1 - 10

9
One front-door station can be allocated to each button of the comfort keypad.
In case of an incoming door call from the fi rst front-door station:
• The LED next to the function key blinks and a ring tone sounds (one time).
Speaking:
• Press the speech button, the call (the last call, if several calls come in in quick succession)
is accepted and a voice connection is established.
Specifi c door calls:
• By pressing the function key of the allocated front-door station, a voice connection is
established.
• The LED is on.
Door release:
• Press the blue door release button during the voice connection.
• Pressing the function key of the allocated front-door station triggers the specifi c door
release.
• The LED expires.
End the call:
• Press the speech button, the call OFF-button or the door release button (the call ends
after 4 seconds or automatically after 2 minutes).
• The LED expires.
Toggle:
• Press the speech button after an incoming call.
• Then press the function key with which you can select the second front-door station.
• The connection with the front-door station which called last is disconnected and a voice
connection to the second front-door station is established. The LED next to the function
key is now on permanently.
Operating the function keys 1 - 10
Specifi c door calls /
door release
Function

10
Specifi c internal calls Each function key of the comfort keypad can be programmed for any indoor station as
destination device for the internal calling.
In case of an incoming call:
• The LED next to the function key blinks slowly.
Speaking:
• Press the speech button, a voice connection to the calling indoor station is established.
• The LED is on permanently.
End the call:
• Press the speech button, the call OFF-button or the door release button (the call ends
after 4 seconds or automatically after 2 minutes).
• The LED expires.
In case of another incoming internal call:
• If there is a second call from an indoor station during a voice connection or after an
incoming call from an indoor station, also the LED next to the function key blinks, to
which the function internal call of another indoor station was programmed.
• A voice connection to this indoor station can be established also up to 2 minutes after
the call came in (as long as the LED blinks).
Call an indoor station internally:
• Press the function key, which is allocated to the second indoor station.
• The LED blinks fast.
• If the call is accepted at the called indoor station, a voice connection is established.
Operating the function keys 1 - 10Function

11
Sensor functions/
status indications
Activate / deactivate
call diversion
Switching without
feedback
Switching with feedback
Button not assigned
Each function key of the comfort keypad can be programmed so that the belonging
LED indicates the contact state of a detector (an attention tone sounds).
• Additionally, an allocated function can be triggered by pressing the button next to the
LED.
• The LED expires if the indicated status ends, an attention tone sounds.
Each function key of the comfort keypad can be programmed so that incoming door
calls are diverted to any indoor station.
• Activate: press the function key, the LED is on.
• Deactivate: press the function key again, the LED expires.
Pressing a function key of the comfort keypad sends a control function. The LED next
to the function key is not activated.
• Press the function key.
• A control function is sent; this one can be allocated to different functions within the
system (button 1: control function 11 .... button 10: control function 20).
Pressing a function key of the comfort keypad sends alternaltive two control functions
(On/Off). The LED next to the function key is activated resp. deactivated.
• Press the function key, the LED expires.
• A control function is send (button 1: control function 11 to button 10: control function
20).
• Press the function key again, the LED expires. Another control function is send
(button 1: control function 41 .... button 10: control function 50).
When pressing the function key no signal is send (delivery state).
Operating the function keys 1 - 10Functions

12
Labeling the function keys 1 - 10
There is an embedded black cover with a little slot on the right side located at the
underside of the device near the labeling fi eld.
Please insert the enclosed opening tool (small metal angle) into the slot and softly
press the tool upwards to loosen the name plate cover from the housing. Pull the labe-
ling cover downwards from the housing together with the labeling carrier.
The labeling stripe can be easily removed, the programmed button functions can be
entered.
Insert the complete labeling carrier back into the guidance rail until the cover is locked
into place by a magnetic holder.
Please fi nd suitable labeling templates on our website.
www.carus-concepts.com

13
Labeling the function keys 1 - 10

14
Notes

15
Notes

16
Notes

17
Notes