Accuride ST8201 User manual

1
MODEL ST8201
Up to 275 lbs. [124.73 kg] Capacity*
Bottom-Mount
APPLICATIONS: Designed for use in heated and refrigerated
drawers in food service equipment that requires routine clean-
ing and disassembly. NSF-certified.
Part Number Slide Length Slide Travel A B
8201-16 15.75 [400] 15.25[387] 15.75 [400] 7.37[187]
8201-18 17.72 [450] 17.22[437] 17.72 [450] 8.36[212]
8201-20 19.69 [500] 19.19[487] 19.69 [500] 9.34[237]
8201-22 21.65 [550] 21.16[537] 21.65 [550] 10.33[262]
8201-24 23.62 [600] 23.13[587] 23.62 [600] 11.31[287]
8201-26 25.59 [650] 25.09[637] 25.59 [650] 12.29[312]
8201-28 27.56 [700] 27.06[687] 27.56 [700] 13.28[337]
8201-30 29.53 [750] 29.03[737] 29.53 [750] 14.26[362]
Stainless Steel (441)
Even lengths 16" - 30" [400 mm - 750 mm]
Full Extension
3.06" [77.6 mm]
0.950" + .060"/-.020" [24.13 + 1.52/-.51]
Bottom-Mount
#10 hex (not included)
Progressive Movement
Self-closing action, adjustable tilt-angle,
auto-relock, NSF-certified and
dishwasher-safe
Up to 275 lbs.
300,000 cycles (Tested on 18" slides in a
30" wide drawer at gross load of 125 lbs.).
400lb (Tested at full extension for 24 hours)
-4°F to + 176°F
[-20°C to + 80°C]
Material
Lengths
Travel
Height
Side Space
Mounting
Hardware
Movement
Features
Load Rating
Cycle Rating
Static Load
Operating
Temperature
Range
Extended Flange (E)
1.53
Standard Flange (S)
[10.2]

2
Before starting the installation process, the slides must be dis-
assembled into the individual three members. Extend the slide
members and follow the steps as shown in Figure 5. Remove the
drawer member and then follow steps shown on Figure 11 and 12
to remove the intermediate member.
Drawer Member Mounting
To install the drawer member, secure inner member to drawer.
(Welding is optional). See Figure 1.
Mounting Instructions
Drawer Front
Figure 1
Cabinet Member Mounting
Align the cabinet member (outer member) at the proper height so
that the drawer can be inserted with no interference. Install the
cabinet member using #10 hex screws, and ensure slides are
parallel. See Figure 2.
To modify angle, remove screws 1 and 3 and rotate around
screw 2 to desired angle and reinstall, as shown in Figure 3.
Figure 3
Flat (0°) Mounting 2° Back Angle 4° Back Angle
Angles may vary by slide length
Figure 4
Intermediate Member Insertion
Insert intermediate member into the installed cabinet member,
as shown in Figure 4.
Drawer Insertion
Before starting drawer insertion, ensure the following:
• Intermediate member should be nested inside cabinet
member.
• Extend intermediate member and lift the drawer release lever
as shown in Figure 5.
WARNING: Drawer release lever must be up
to insert drawer.
Figure 5
NOTE: Member does not come with pre-drilled holes.
Recommended use of #8 hex flathead screws.
Screw 2
Screw 3
Screw 1
Cabinet
Cabinet
Front
Instop
Cabinet
Figure 2

3
Mounting Instructions (continued)
NOTE: Upon drawer closure, drawer will reset the drawer
Drawer Removal
To remove drawer, fully extend unit, then released the locking
lever by pulling up (see Figure 10). To remove, drawer must
be lifted at an angle as shown in figure 7.
Figure 11
WARNING: Drawer release lever must be forward
(towards user) to remove drawer.
Intermediate Member Removal
Lift latch tab and pull (as shown on Figures 11and 12).
Pull
Pull
Figure 6
Once lever is released, drawer insertion can begin. The
drawer begins by riding over the rollers (Figure 6), then lifts
past the stop to engage with the middle rollers (Figure 7). The
drawer then stabilizes into the horizontal position (Figure 8).
Figure 7
Figure 8
NOTE: Upon drawer closure, drawer will reset the drawer
release lever. Ensure release lever is engaged
(See Figure 9).
Figure 9

Copyright © 2023Accuride International Inc. 3700-9599 (1282) MK201-R7-0323
Customer Supplied Hardware
Slide Ordering Instructions
Complete your order for Accuride Model ST8201 by specifying the
following:
20 pr ST 8201-XX S D
Total Required Slides
Slide Material
Slide Model
Slide Length
Flange
Packaging
Flange options: S=Standard; E=Extended
Packaging Information
Distributor (D) Pack: Box quantities vary by length (hardware
not included), one pair of slides packaged in a polybag
with a technical sheet.
Slide lengths 16"-22" 8 slides per box
24"-30" 4 slides per box
Bulk (P) Packaging: Quantities vary by length, slides only
(hardware not included). Left and right hand slides packaged
in separate boxes.
Slide lengths 16"-22" 8 slides per box
24"-30" 4 slides per box
To order bulk pack specify ST8201-28S-L for the left hand
and ST8201-28S-R for the right hand.
Specifications
Slide Members: 441 Stainless Steel
Rollers: Dupont™Delrin®
NSF-certified
RoHS compliant
NOTE: Specifications, materials, prices, terms and delivery are
subject to change without notice.
4
For the most current technical information visit www.accuride.com
Accuride International Inc.
12311 Shoemaker Avenue
Santa Fe Springs, CA 90670
TEL [phone]
FAX [phone]
Manufacturing, Engineering, and Sales
United States • Germany • Japan •
Mexico • United Kingdom • China
WARNING: This product can expose you to chemicals including nickel,
which is known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Cabinet Member: #10 hex-head screws