Accuride CBERGO-TRAY 200 User manual

CBERGO-TRAY 200
Standard Keyboard Tray System
APPLICATIONS: For wood or metal furniture in home office
furniture and office workstation desktops. This product is
covered by U.S. (D447,145 S) and foreign (ROC 74826)
patents issued and/or pending.
Finish: Black powder-coated (CB) finish
Unit Profile: Width: 29.6" [751.7]
Depth: 19-1/2" [495.3]
Slide Travel: 11.0" [279.4]
Tray Profile: Inside tray width: 25-1/2" [647.7]
Inside tray depth: 9-13/32" [239.0]
Mounting
Space: Minimum 30.0" [762.0]
Load: Slides are rated to carry 75 lbs.
Brackets: Variable height,
Inboard/Outboard.
Tray Fit: Fixed at -7°
Features
• Ergonomic design
•Slides fully concealed from view
•All rough edges and pinch points eliminated
•No transfer of grease
•Accommodates any size keyboard by removing palm rest
•Large tray width provides unhanded mouse surface
•Removable full-length foam palm rest
•Cable management fixtures incorporated in rear of tray
•Slides silenced in the open and closed positions
•Detent-in and detent-out
End Cap
Palm Rest Mouse Pad End Cap
25-1/2"
[647.7]
9-13/32"
[239.0]
Keyboard Tray
Cable Management
Reversible Adjustable
Brackets
24-3/4" [628.7] Bracket
30-3/8" [771.5] Bracket Outboard
mm
Inches
3/4 Extension Ball Bearing Slides

Before you begin, unpack the new keyboard assembly and
inspect it for damage. If there is any damage or the product
does not operate properly, contact your Accuride Distributor for
further details.
NOTE:
The keyboard assembly is designed and intended for the
support of a keyboard mouse, and mouse pad only. The
mounting screws included are suitable for mounting the
assembly into wood or metal units. All eight mounting screws
should be fully tightened to mate the bracket to the mounting
surface.
Caution: Always protect your eyes and wear safety goggles or
glasses during installation.
• #2 Phillips Screwdriver (Minimum 6" long shank)
•Drill (6" long screwdriver bit required for inboard
mounting)
• Scratch Awl
•1/16" Drill Bit
•Use the sturdiest material possible. Minimum 3/4" thick
composite (MDF, plywood, or particle board) is
recommended.
Step 1
• Determine the preferred mounting location of the
keyboard assembly.
•For flush mounting, fold the installation template on the
dotted lines and align the front edge (as noted) to the
edge of the work surface. Otherwise, adjust the
installation template to fit the desired location.
•Tape installation template in place.
Step 2
• The mounting brackets can be mounted "Inboard" or
"Outboard". Determine the orientation of the mounting
brackets that best suits the application. See Figure 1.
Step 3
• Punch eight pilot holes with a scratch awl and drill eight
1/16" diameter starter holes in the designated installation
template locations for the selected mounting style
(inboard or outboard).
NOTE: Use caution when drilling pilot holes to avoid
drilling through to the top of the desk.
Step 4
• Remove installation template.
Step 5
• The unit is shipped with the mounting brackets installed
in the lowest inboard setting. Remove and adjust as
required.
Installation Instructions
Figure 1
Figure 2
Figure 3
2
Outboard Bracket Position - or - Inboard Bracket Position
Work Surface
# 8 Screws # 8 Screws
Work Surface
Seven
Bracket Positions
2-3/8" [60.3] Min.
3-5/8" [92.1] Max.
Work Surface
Access Hole Provided
Tools Required
Suggested Mounting Surface
Installation Procedure
Bracket Screw
(Self-Tapping) 4-1/4" [108.0] Min.
5-1/2" [139.7] Max

Figure 7
Adjusting Optional Bracket
•Using a Phillips screwdriver, remove the bracket screws. See
Figure 2. Position the brackets to accommodate the preferred
height and mounting orientation.
•Ensure that each bracket is adjusted to the same vertical
setting.
•To maximize knee space, adjust brackets just enough to clear
keyboard during travel.
•The self-tapping bracket screws can be installed from either
direction. When repositioning brackets, make sure to reinstall
the same screws.
Step 6
• While holding the unit in place, fasten the two rear brackets
to the work surface with a Phillips screwdriver (start with
one screw per bracket). Each bracket will use two #8 X 5/8"
screws.
•While holding the unit in place, extend the keyboard drawer
to the fully open position. See Figure 3. Fasten the two front
brackets.
NOTE: Fully tighten the screws on one side.
After all the brackets have been
fastened, cycle the unit a few
times to ensure the slides have
self-adjusted to a parallel movement
and are moving freely.
Step 7
•After the unit has been cycled a few times, the slide alignment
has self-adjusted. Close keyboard slightly, tighten the rear
bracket screws on the other side, and install the remaining
screws.
•Extend tray fully and install the remaining screws in the front
bracket.
•If the brackets are not properly aligned, a slight dragging will
be evident.
•Locations for mouse cable management can be found at
the rear left or rear right of the tray at the back of the end
cap assembly. See Figure 4.
•The mouse cable is held in place by positioning it between
the two small pins and pressing into place.
•If a free-moving mouse cable is preferred, position cable
be tween the large and small pins.
•An oval cut-out located in the center of the keyboard tray is
provided for keyboard cable management.
3
Detail of Mouse Cable Management
End Cap Assembly
Cable Management

Ordering Instructions
ACCURIDE INTERNATIONAL INC.
12311 Shoemaker Avenue
Santa Fe Springs, CA 90670
TEL [phone]
FAX [phone]
www.accuride.com
Manufacturing, Engineering, and Sales
United States • Germany • Japan • Mexico • United Kingdom • China
For the most current technical information visit www.accuride.com © 2013 Accuride International Inc. 3700-9427-MK076-R5-0214
Complete your order for Accuride model CBERGO-TRAY 200 by
specifying the following:
20 Each CBERGO-TRAY200
Packaging
NOTE: Specifications, materials, prices, terms, and
delivery are subject to change without notice.
Total units required
Model
Slide Members:
Ball Retainers:
Ball Bearings:
Keyboard tray:
Palm rest:
Mouse Pad:
End caps:
RoHs compliant.
Cold rolled steel
Cold rolled steel
Carburized steel
Cold rolled steel
Foam
Foam
ABS, molded plastic
4
Specifications
Individually packaged in special carton with slides with slides
attached to the keyboard tray. Includes hardware mounting kit
4180-0395-XE, which includes:
8 each 2410-3241-CE #8-17 x 5/8" self-tapping screws