aci KW350-P1-D-S-RC User manual

K W350-P1-D-S-RC
Quick Setup Guide
·Appearance and Dimension
·
Installation Method
·
Terminals
·
Wiring Diagram
·
Settings Mode
·
Communication
·
Energy Pulse Output
·
Event Logging
·
2
Appearance and Dimension
Installation Method
Steps:
1. To install the meter on the rail insert the top of the rail into the groove on the
back of the meter. Pull the metal clips back and slide the rail across the groove of
the meter.
Unit: mm
Front View Side View
3
2. Use the metal clips to tighten the rail to complete installation.
3. Before mentioning this step, the steps needed to remove the seal/cover need to
To attach seal/cover back onto the meter place the left side of the cover down onto
meter and press down on the right side. When installed correctly you will hear a
clicking sound. The steps to attach the other cover is opposite to the above step.
4. After inserting the cover, tighten the sealing screws and lay the seal.
Pulse Output
Isolation Voltage 2500Vac
Load Voltage 0~250Vac
Load Current 100mA(max)
Relay Output
Load Voltage 250Vac 30Vdc
Max Load Current 5A(Resistant Load)
Isolation Voltage 2000Vac(1min)
Action Time 10ms
Mechanical Life 20 million times
Electrical Life About 50,000 times(5A, 250Vac,Resistant Load)
Communication
RS485 Baud Rate 1200~38400
Communication Protocol ModBus-RTU
Infrared Communication Non-contact infrared
Infrared Baud Rate 1200
Environment
Working Temperature -25~70°C
Storage Temperature -40~85°C
Automation Components, Inc.
Phone: [phone]
Web: www.workaci.com
Email: [email protected]
Document#2304E3201 Revision Date: Apr., 2021 4
Terminals
5. To open the cover, remove the seal if applicable, unscrew the sealing screws and
life the cover upwards to remove.
5
Wiring Diagram
3 phase 4 wire (3LN, 3CT)
KW350
3 phase 3 wire (2LL, 3CT)
KW350
2305 Pleasant View Road, Middleton WI

6
N GL
220Vac
com
V+
R1
R2
RO
Auxiliary Power
Module
P1
P2
DO
V+
OUT
COM
Relay Output Wiring Diagram Pulse Output (DO) Wiring Diagram
Settings Mode
Meter Setting
Press and release the “SET” key to enter settings mode, now the password is
pressing the “SCROLL” key, and shift the cursor by pressing the “SET” key. When the
input. The meter’s default password is 0000. After entering the settings mode, you
also be change through the PC software.
7
LCD Page Contents KW350
Addr Address S-01
bd Baud Rate S-02
Pr Parity S-03
Ct CT1 S-09
CT2 S-10
Pt PT1 S-11
PT2 S-12
In settings mode, scroll to the page S-01 to set the communication address, the
address can be any integer between 1 and 247. Setting method is as follows: Press
shift the cursor by “SET” key, when the cursor is moved to the rightmost location,
The other settings are the same as the operation of address.
The communication baud rate can be set to 1200, 2400, 4800, 9600, 19200 or
38400.
The communication parity can be set to EVEN, ODD, NONE1 or NONE2.
Communication
KW350 meter communication uses RS485 interface and Modbus -RTU
protocol. Wiring terminals are A, B, S. If master device does not support RS485 but
only RS232, an adapter named RS232/RS485 needs to be used for connection. In
practical alapplications, there are multiple topologies for RS485 network, such as
Line, Star and Wye. In addition, the Display Module has an infrared port to support
8
Energy Pulse Output
Users can choose either energy pulse output or reactive energy pulse output. The
energy pulse output function needs an external auxiliary power to supply.
Relay Output(RO)
Two modes available: control or alarm output. One module only supports one
mode at a time.
Event Logging
The KW350 series also provides a system status self-testing feature. When
crucial operations are implemented (such as programming, open/close the cover,
clear the demand, clear the meter's data etc), it immediately logs the event time
and the event type.
Current Input
Rated Current 100mV (1A)
Start Current 10mA
Accuracy 0.5%
Voltage Input
Rated Voltage 400Vac L-N 690Vac L-L
Input Impedance 2MΩ/Phase
Measurement Frequency 50/60Hz
Accuracy 0.5%
Power Supply
Working Power Supply 100~415Vac,50/60Hz; 100~300Vdc
Power Consumption <2W or 10VA
KW350