Growatt ShineWiFi Instruction sheet

Growatt ShineWiFi
Quick Installation Guideline
Search “Shine Phone” in google play or app store, or scan
the picture below, download and install the app.
Register and Add device
For more info, please download from http://server.growatt.com
NOTE: 1.Please install the latest version;
2.For more details, please refer to the content on
server.growatt.com.
【Android& 】iOS
[phone] [phone]
[e-mail]
Step1.
A If there is a DIP switch next to the RS232 port, please set DIP 1 to “ON”. Then plug in the ShineWiFi and lock screws.
B If there is no DIP switch, poke the small rubber plug from the screw hole adjacent to the RS232 port. Plug into the RS232 port and
lock screws.
Electrical Connection
Step2. 1.Connect your mobile phone to the WiFi of the router which ShineWiFi will connect to.
3.Then enter the SN and check code of the or just
scan the QR code on it in the following page to add the
into this account.
ShineWiFi
ShineWiFi
4.Then it will jump to the configuration page –
“Set ShineWiFi”, enter the WiFi password in the
corresponding field. Please note, the phone must be
connected to the WiFi network of the router first.
6. Login your account. Click the “+” at the top right
of the page to view the connection status of the data
logger(ShineWiFi).
Remark:The connection status of the can be
checked by the status of the blue LED light beside the Key button
in the
1. Blue LED status:
Solid on: device is initializing
Solid off: no device found on RS232 port
Flashing fast (change every 0.2s): Found inverter or SP2000 on
RS232 port
Flashing slow (change every 1s): The is online and
successfully connected to router
2.If you need to reconfigure the , please press and
hold the key button for at least 3 seconds until the blue LED
turns solid on and flash fast. Now open the ShinePhone App and
long press the in the datalogger list to configure
it again.
ShineWiFi
ShineWiFi
ShineWiFi
ShineWiFi
ShineWiFi
2.Run ShinePhone, and register a new account;
Remove the cover of the RS232 port, check if there is a DIP switch next to the port.
5. After entering the WiFi password, click on “Configure” to
start the configuration. A “configuration successful
acquisition” dialog window will appear if the ShineWiFi is
successfully configured. Click “OK” on the dialog window,
you’ll be brought to the login page.
7. Then click the “Device” tab at the bottom line to move to
“Device” page, All detailed information of the PV system
can be viewed here.

快速安装指导
扫描以下二维码,或在谷歌商店或苹果商店搜索“ShinePhone”,
下载并安装软件。
A 当逆变器RS-232接口的旁边有一个DIP开关时，先将逆变器RS-232接口旁的拨码开关1置于”ON”位置，然后将ShineWiFi的RS-232接口与
逆变器的RS-232接口对接 ，并用螺丝将ShineWiFi固定在逆变器上。
注册添加设备
1. 首先将手机连接到有无线网络的路由器
4. 进入“配置ShineWiFi”页面，输入需要连接的Wi-Fi路由器密码，
注：配置前请确认手机已连接到Wi-Fi路由器；
6. 登录帐号进入“我的电站”，点击右上角“+”查看采集器
是否已接入在线 ;
备注：可以通过ShineWiFi上蓝色LED灯的闪烁情况来判断
ShineWiFi的连接状态
1.蓝色LED灯状态指示：
常亮：设备初始化
常灭：RS232端口没找到设备
快闪(周期0.2秒变化)：RS232端口找到设备
慢闪(周期1秒变化)：网络通信正常
2.如重复配置采集器的WIFI连接，请长按采集器主体KEY键3秒以上，
直到蓝色LED灯变为常亮，等待LED灯变为快闪，在
ShinePhone App采集器列表页面长按此采集器选择“配置采集器”。
电气连接
详细信息及最新用户手册，请到http://ser ver.growatt.com下载
[phone] [phone]
[e-mail]
3. 进入添加采集器页面，手动输入或扫描采集器序列号及验证码
完成添加;
戳在这里
备注：1. 确保安装的是最新版本的软件；
2. 详情请参考server-cn.growatt.com上的内容 。
【安卓&苹果】
Growatt ShineWiFi
B 当逆变器RS-232接口的旁边没有DIP开关时，先将防水垫片上的橡胶塞用螺丝刀戳开，然后将ShineWiFi的RS-232接口与逆变器的RS-232接口
对接，并用螺丝将ShineWiFi固定在逆变器上.
Step2.
用螺丝刀将逆变器RS-232接口上的防水金属片卸下:
2. 运行ShinePhone , 注册用户,填写用户信息；
5. 点击“配置”开始配置，等待页面弹出“采集器配置成功”后点击
确定，自动跳转到登录页；
7. 在“我的电站”点击所监控设备，查看光伏设备信息 ;