Acksys WaveNet-EX Series User manual

Documentation ref DTUS075 rev A0 06/18/20
-1-
WaveNet-EX Series
Quick installation guide
WiFi MIMO access point & Mesh router for
hazardous areas
WiFi Access Point, WiFi client, repeater, router & Mesh point
(A10 and A12 only)
ATEX / IECEX certification :
Zone 1, 2, 21 & 22
II 2G Ex db IIC T5-T4 Gb
II 2D Ex tb IIIC T110°C/T140°C Db
I M2 Ex db I Mb (SWS only)
USA & CANADA CERTIFICATION
Class I, Division 1, Groups B, C and D
Class II, Division 1, Groups E, F and G
Class I, Zone 1, Groups IIB+H2 [For U.S. only]
Zone 21, Groups IIIC [For U.S. only]
Heavy duty aluminum (SWA series) or stainless steel (SWS
series) IP66/IP68 enclosure
2 or 3 intrinsically safe RF outputs
Gigabit Ethernet network interface
DC power supply input (+18VDC to +60VDC), PoE or PPoE
(Passive Power over Ethernet)
Before starting, please check the product kit part listing below. Contact
immediately your dealer if any item is missing or damaged:
One WaveNet-EX
This quick installation guide printed
Before continuing, check thanks to the ACKSYS website: www.acksys.fr/en
If a latest update of this quick start is available
Download and read the full manual « WaveOS user guide ».
You will need:
a PC equipped with Ethernet access to install the
« WaveManager » software,
a web browser, IE compatible,
an android smartphone if you want to install the optional
« ACKSYS WaveViewer » App.
Copyright © 2020 by ACKSYS. Under the law of March 11, 1957, the reproduction in
whole or in part of this work, by any means whatsoever, is prohibited without the prior
written consent of ACKSYS.
Disclaimer.This document does not constitute a contract. ACKSYS does not guarantee
its contents in any way and accepts no responsibility regarding the profitability of the
products described or their suitability for the user's needs. Under no circumstances can
ACKSYS be held responsible for any errors that may be contained in this document, or for
damages, no matter what their extent, that result from the supply, operation or use of the
products. In its ongoing efforts to improve its documentation, ACKSYS reserves the right
to revise this document periodically or to change all or part of its content, without incurring
any obligation to notify any party whatsoever.
10, rue des Entrepreneurs
Z.A Val Joyeux
78450 VILLEPREUX - France
Phone [phone]
Fax : [phone]
Web : www.acksys.fr
Hotline : [e-mail]
Sales : [e-mail]

-2-
READ THIS INSTRUCTION FIRST
To avoid serious or fatal personal injury or major property damage, read and
follow all safety instruction in this manual. If you require additional assistance,
please contact ACKSYS.
This product must be installed and maintenance according to suitable
standards for electrical application in potentially explosive atmospheres
(example: IEC/EN 60079-14, IEC/EN60079-17 or other national standards).
Read this first and keep this instruction manual always available.
This instruction refers to certified equipment covered by the EXA 14 ATEX
0042, IECEx EXA 14.0001 and by LR1504 certificate.
NOTE
1. Suitably trained personnel shall carry out installation according with
applicable code practice.
2. Cover must be tightening with a torque of at list 15 Nm.
3. To avoid the thread cover blocking the thread joint can be protect with
grease like Nyogel 760G, Uniflor 8512R, Uniflor 8911 or equivalent
compatible with silicon gasket
4. The user should not repair this equipment.
5. The user should not modify the enclosure and related components inside.
6. For ambient temperature below -10°C and above 70°C use field wiring
suitable for both minimum and maximum ambient temperature.
7. The electrical devices must be grounded using their grounding
connections.
8. The user should guarantee the keeping of the safety characteristic of the
device after maintenance.
9. If the equipment is likely to come in to contact with aggressive substances,
it is responsibility of the user to take suitable precautions that prevent it from
being adversely affected, thus ensuring that the type of protection is not
compromised. Aggressive substances: example Acids, liquids, gases with
can affected metals.
10. The metallic alloy used for the enclosure, in the event of a rare accident,
could cause ignition sources due to impact or friction (sparks may occur).
This shall be considered when the box is installed in group Ex area.
11. Remove plastic plugs or plastic stickers supplied with enclosure before
installation, these components aren’t certified. All cables entry devices and
blanking elements shall be certified in the type of explosion protection
flameproof type “d” and “tb” suitable of use in Ex area and correctly installed.
12. For functionality of device installed inside the enclosure refer to device
instruction
WARNING!
Warns of hazard that MAY cause serious personal injury, death or major
property damage.
HAZARDOUS VOLTAGE
Disconnect all power before servicing equipment.
DO NOT REMOVE COVER WHEN ENERGISED.
DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT.
CAUTION!
The conduit plug supplied with the switch boxes are for transit purposes only.
IP66/68 protection depends on cable gland and cabling methods used.
Before the installation verify into the Annex to Installation & Operation manual
the limitation to use and the accessories allowed.

Documentation ref DTUS075 rev A0 06/18/20
-3-
NOMENCLATURE
SWA
A10
33
-
42
0
X0
1
2
3
4
5
6
1 – Enclosure
SWA Aluminium polyester powder coated
SW S S tai nles s steel AISI 316 (CF8M) electropolish
4 – Cable entries
42 n° 4 3/4” npt-f (two used for antenna connection)
44 n° 4 M25x1.5 (two used for antenna connection)
2 –Device code
A10 802.11n, MIMO 2x2
A11 802.11ac, MIMO 2x2
A12 802.11n, MIMO 2x2 plus 802.11ac (1 stream)
5 – Colour
0 black polyester powder coating (SWA series only)
E electropolished (SW S housings only)
3 – Antenna connection
30 n° 3 RXN antenna coupler (N Female)
33 n° 2 RXN antenna coupler (N Female)
6 – Approvals
X0 Atex/IECEx Gas and Dust certified, Zone 1, 2, 21 & 22
M0 Atex/IECEx Gas, Dust and mining certified, Zone 1, 2, 21 & 22
N0 QPS CL1 DIV1 and North American Zones listed
PRODUCT’S STORAGE
Keep the boxes away from atmospheric agents in an environment with
temperature between 0°C and 40°C.
INSTALLATION
Attach the enclosure to a fix surface using four M6 bolts
The unit can be installed in all position.
ELECTRICAL WIRING
Remove screw cover, remove protection plugs from cable entries and
substitute them with cable glands or conduits or plugs suitable for type of
protection required.
Connect terminal strip according to the wiring diagram present into the Annex
to Installation & Operation Manual.
Reassemble screw cover and lock it by means of the screw or anti rotation
kit.
WARNING: Before closing the enclosure check that thread joint were free of
foreign matters and deformations check seal is properly fitted in slot.
The cover must be screwed and securely locked to the body.
MAINTENANCE
The verification and maintenance of the electrical equipment must be
performed according to IEC/EN 60079-17.
The cover must be securely locked to the body.
After every opening must to check before closing
that he thread joint is free of foreign matters and
deformations and if necessary lubricate the thread
joint in order to avoid cover blocking with grease
like Nyogel 760G, Uniflor 8512R, Uniflor 8911
compatible with silicon gasket or equivalent
according to enclosure temperature range.
In order to guarantee the protection degree IP66-
68 it’s necessary that the gasket is maintained in
good conditions and must be verified after every
opening that the same does not show breakage or
cuttings. In case of damage replace with ACKSYS spare part.
The maintenance related the components used for wiring must be performed
according to manufacturer instruction.
DISPOSAL / RECYCLING
Disposal and recycling of the product according to national regulation for
waste disposal and recycling.
WARNING: Do not dispose the product and the components in the
environment.

Documentation ref DTUS075 rev A0 06/18/20
-4-
DESCRIPTION
The SWA & SWS A series is a WiFi access point equipped with 1 Ethernet
port and up to 3 WiFi ports as follows:
Device
version Model
WiFi
Port
A10 WiFi Access point 802.11n MIMO 2x2 n° 2
A11 WiFi Access point 802.11ac MIMO 2x2 n° 2
A12
WiFi Access point 802.11n MIMO 2x2
plus 802.11ac (1 stream) n° 3
A10
A11
A12
POWER SUPPLY
Screw terminals = Supply voltage: 18 ~ 60 VDC
RJ45 connector = PPoE @ 24 VDC or PoE @ 48 VDC *
Max Power Consumption 8W for A10 / 14W for A11 and A12
* PPoE = Passive Power over Ethernet (operating voltage 24VDC), PoE =
Power over Ethernet (operating voltage 48VDC)
TEMPERATURE RANGE
Device version Model Ambient temperature range
SWA Aluminum enclosure min -40°C – max +60°C
SWS
Stainless steel
enclosure
min -40°C – max +50°C
WARNING : The unit can reach a surface temperature of 70°C, use cable
and cable glands / conduit Ex certified suitable for this temperature.

Documentation ref DTUS075 rev A0 06/18/20
-5-
WIRING
Label
Description
RJ45 LAN connector
(PPoE @24VDC or PoE @
48VDC)*
J1
Label
Description
-
Power supply - (18 ~ 60 VDC)
+
Power supply + (18 ~ 60 VDC)
F1
Label
Description
750mA
5x20 mm power line fuse
(750mA fast-blow type)
Label
Description
PWR
Power led indication
DIAG
Diagnostic led indication
SW1
Label
Description
RESET
Reset button
SW2
Label
Description
POE/PPOE
DIP switch for PoE / PPoE
selection *
1 ON = 48V = PoE
1 OFF = 24V = PPoE
DIP switch operate only in case of PoE/PPoE power
supply
* PoE = Power over Ethernet
(operating voltage 48VDC)
PPoE = Passive Power over Ethernet
(operating voltage 24VDC)
Step 1 – ANTENNA CONNECTION
Connect the antenna before to turn on the device.
WARNING : use antenna only with 50Ω impedance and with operating
frequency in according to technical data listed into the above paragraph “RF
information”.
The device must be set according to limitation listed at paragraph MAXIMUM
PERMITTED RF THRESHOLD POWER (Pth) for installation in Hazardous
Location and the national regulation rules.
Step 2 – POWER SUPPLY CONNECTION
WARNING : DO NOT WIRED POWER SUPPLY WHEN AN EXPLOSIVE
ATMOSPHERE IS PRESENT.
FOR SAFETY REASONS WIRING MUST BE MADE ACCORDING TO WA
& WS INSTALLATION AND OPERATION MANUAL
The device can be powered by terminal strip (J1 18 ~ 60 VDC) or through
PoE/PPoE.
In case of PoE (Power over Ethernet, 48VDC) set the DIP Switch SW2 nr. 1
to ON,
In case of PPoE (Passive Power over Ethernet, 24 VDC) set the DIP Switch
SW2 nr. 1 to OFF
The DIP switch position has no influence in case of power supply through
terminal strip J1
The device has no ON/OFF switch. It turns on automatically when power is
applied. Check that the PWR led turn on.

Documentation ref DTUS075 rev A0 06/18/20
-6-
The DIAG led stay off for around 40 seconds, until the device is fully ready to
use. Then the DIAG led turns blue.
Step 3 – ETHERNET CONNECTION
Connect the Ethernet cable (if it not connected in case of PoE or PPoE).
DEVICE CONFIGURATION
FACTORY SETTINGS:
IP address: 192.168.1.253
Radio Interface disable, preset for access point mode
SSID: acksys (broadcast)
No security (no WEP, no WAP, no WAP2, no MAC filter)
802.11n or ac mode, 5GHz band, auto-channel
WEB interface for device configuration:
IP address: 192.168.1.253
User name: root
Password: no password set as factory setting
Step 1
Verify that the IP address factory setting is compatible with your network, if
the IP address is not suitable for your network use Windows application
WaveManager (available on web site www.acksys.fr).
After the WaveManager installation run the application, select the
EmbedAir1000 device then click to “Setup”: now you can configure the IP
address or you can activate the DHCP client.
Step 2
Using your web browser open the WEB interface (IP address: 192.168.1.253)
and select the “SETUP” tab:

Documentation ref DTUS075 rev A0 06/18/20
-7-
For setup page, user name and password are required and for factory setup
the user name is root and no password is required (these data can be
changed under “TOOLS” tab, PASSWORD SETTINGS section)
On the “WIRELESS INTERFACES OVERVIEW” page you should first select
your country in order to enforce applicable regulation rules. The country
selector is located in the global parameters, near the bottom of the page.
You can select radio interface to set up its WiFi parameters (you can also
change IP configuration and services).
In function of device version the WiFi Interface available are:
Device
version
Model
WiFi Interface
used
A10 WiFi Access point
802.11n MIMO 2x2
WiFi Interface 1
only (antenna 1
and 2)
A11 WiFi Access point
802.11ac MIMO 2x2
WiFi Interface 2
only (antenna 1
and 2)
A12
WiFi Access point
802.11n MIMO 2x2
plus 802.11ac (1
stream)
WiFi Interface 1
(antenna 1 & 2)
and
WiFi Interface 2
(antenna 3)

Documentation ref DTUS075 rev A0 06/18/20
-8-
For WiFi and LAN interface setup click on relative menu on “PHYSICAL
INTERFACES” menu:
Set for each WiFi interface the following essential parameters:
The operating mode: 802.11 mode, radio channel (take care about
local legislation), SSID
WiFi security parameters (WEP, WPA, WPA-PSK, WPA2, WPA2-
PSK, SSID broadcast or not)
For more details consult Acksys WaveOS User Guide.
TROUBLESHOOTING AND LED DEFINITION
None of the LED indicators turn ON
Verify the power supply (voltage, cabling)
Verify the fuse F1
The WiFi link does not come up
Make sure that the Wireless parameters of the Client (case sensitive
SSID, 802.11 mode, radio channel and security) match those of the
AP
Check the radio conditions: distance between devices, placement of
antennas, interferences and obstacles to radio waves propagation
Try with all securities and encryption settings temporarily disabled
Try another radio channel
How to restore factory settings?
If the built-in web-based interface is reachable, you can use a browser
to restore factory settings.
Else, power up the unit, wait for the DIAG led to turn blue, then hold
down the reset button (for at least 2 seconds) until DIAG goes off.
Then release it and wait for the DIAG led to turn blue again, meaning
that the product rebooted with its factory settings.

Documentation ref DTUS075 rev A0 06/18/20
-9-
LED Definition
LED Function
PWR Green : power on
Off : power not present
DIAG
Blue : when product is OK and initialized
Flashing : when firmware in flash is not valid
Off : for more then 2min with PWR led green indicate a
Hardware/Software failure
RF INFORMATION
Device
version
A10
ANTENNA 1 AND 2 *
Radio modes: Support for IEEE 801.11a/h, 802.11b, 802.11g and 802.11n
Frequency band for 802.11a/n : 5 GHz; 5.170 to 5.835 GHz
Frequency band for 802.11b/g/n : 2.4 GHz; 2.402 to 2.494 GHz
Tx output power (Radio card output per chain, antenna excluded)
802.11n HT20 2.4GHz band 20.5 dBm @ 7.2 Mbps (MCS 0)
18 dBm @ 72.2 Mbps (MCS 7)
802.11n HT40 2.4GHz band 20.5 dBm @ 15 Mbps (MCS 0)
18 dBm @ 150 Mbps (MCS 7)
802.11n HT20 5GHz band 18 dBm @ 7.2 Mbps (MCS 0)
15 dBm @ 72.2 Mbps (MCS 7)
802.11n HT40 5GHz band 18 dBm @ 15 Mbps (MCS 0)
15 dBm @ 150 Mbps (MCS 7)
Value for 1 stream, add 3 dBm for 2 streams
A11
ANTENNA 1 AND 2 *
Radio modes: Support for IEEE 801.11a/h, 802.11b, 802.11g, 802.11n and
802.11ac
Frequency band for 802.11a/n : 5 GHz; 5.170 to 5.835 GHz
Frequency band for 802.11b/g/n : 2.4 GHz; 2.402 to 2.494 GHz
Tx output power (Radio card output per chain, antenna excluded)
802.11b 2.4GHz band 20 dBm @ 1 Mbps
20 dBm @ 11 Mbps
802.11g 2.4GHz band 21 dBm @ 6 Mbps
18 dBm @ 54 Mbps
802.11a 5GHz band 20 dBm @ 6 Mbps
15 dBm @ 54 Mbps
802.11n HT20 2.4GHz band 21 dBm @ 7.2 Mbps (MCS 0)
16 dBm @ 72.2 Mbps (MCS 7)
802.11n HT40 2.4GHz band 20 dBm @ 15 Mbps (MCS 0)
16 dBm @ 150 Mbps (MCS 7)
802.11n/ac VHT20 5GHz band 19 dBm @ 7.2 Mbps (MCS 0)
14 dBm @ 72.2 Mbps (MCS 7)
13 dBm @ 86.7 Mbps (VHT MCS 8)
802.11n/ac VHT40 5GHz band 18 dBm @ 15 Mbps (MCS 0)
14 dBm @ 150 Mbps (MCS 7)
13 dBm @ 200 Mbps (VHT MCS 9)
802.11ac VHT80 5GHz band 18 dBm @ 32.5 Mbps (MCS 0)
14 dBm @ 325 Mbps (MCS 7)
13 dBm @ 433.3 Mbps (VHT MCS 9)
Value for 1 chain, add 3 dBm for 2 chains (Tolerance ± 2 dB)
A12
ANTENNA 1 AND 2 *
Radio modes: Support for IEEE 801.11a/h, 802.11b, 802.11g and 802.11n
Frequency band for 802.11a/n : 5 GHz; 5.170 to 5.835 GHz
Frequency band for 802.11b/g/n : 2.4 GHz; 2.402 to 2.494 GHz

Documentation ref DTUS075 rev A0 06/18/20
-10-
Tx output power (Radio card output per chain, antenna excluded)
802.11n HT20 2.4GHz band 20.5 dBm @ 7.2 Mbps (MCS 0)
18 dBm @ 72.2 Mbps (MCS 7)
802.11n HT40 2.4GHz band 20.5 dBm @ 15 Mbps (MCS 0)
18 dBm @ 150 Mbps (MCS 7)
802.11n HT20 5GHz band 18 dBm @ 7.2 Mbps (MCS 0)
15 dBm @ 72.2 Mbps (MCS 7)
802.11n HT40 5GHz band 18 dBm @ 15 Mbps (MCS 0)
15 dBm @ 150 Mbps (MCS 7)
Value for 1 stream, add 3 dBm for 2 streams
ANTENNA 3 *
Radio modes: Support for IEEE 801.11a/h, 802.11b, 802.11g, 802.11n and
802.11ac
Frequency band for 802.11a/n : 5 GHz; 5.170 to 5.835 GHz
Frequency band for 802.11b/g/n : 2.4 GHz; 2.402 to 2.494 GHz
Tx output power (Radio card output per chain, antenna excluded)
802.11b 2.4GHz band 20 dBm @ 1 Mbps
20 dBm @ 11 Mbps
802.11g 2.4GHz band 21 dBm @ 6 Mbps
18 dBm @ 54 Mbps
802.11a 5GHz band 20 dBm @ 6 Mbps
15 dBm @ 54 Mbps
802.11n HT20 2.4GHz band 21 dBm @ 7.2 Mbps (MCS 0)
16 dBm @ 72.2 Mbps (MCS 7)
802.11n HT40 2.4GHz band 20 dBm @ 15 Mbps (MCS 0)
16 dBm @ 150 Mbps (MCS 7)
802.11n/ac VHT20 5GHz band 19 dBm @ 7.2 Mbps (MCS 0)
14 dBm @ 72.2 Mbps (MCS 7)
13 dBm @ 86.7 Mbps (VHT MCS 8)
802.11n/ac VHT40 5GHz band 18 dBm @ 15 Mbps (MCS 0)
14 dBm @ 150 Mbps (MCS 7)
13 dBm @ 200 Mbps (VHT MCS 9)
802.11ac VHT80 5GHz band 18 dBm @ 32.5 Mbps (MCS 0)
14 dBm @ 325 Mbps (MCS 7)
13 dBm @ 433.3 Mbps (VHT MCS 9)
* Antenna position