ACME YH-40A-0 User manual

2
INSTRUCTIONS FOR USE
Use precautions:
1. Before use, check and ensure the power voltage and frequency
fan requirements and the power socket is well earthed.
2. These fans enjoy three-level speed regulator: "0" is off or stop
running level; "1" is slow-speed level; "2" is medium speed level; and
"3" is high-speed level.
3.The maximum oscillating angle of these fans is 90º, under the
control of the oscillating switch; upon pressing down the oscillating
button, the fan oscillates, when pulling it ,the fan stops oscillation.
4. The damaged power cord shall be replaced by our service station
or professional personnel.
5. This appliance can be used by children aged from 8 years and above
and with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision
or instruction concerning used of the appliance in a safe way and
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by
children unless they are older than 8 and supervised.
6. Keep the appliance and its cord out of reach of children less than 8
match the
people

3
7. This appliance is not intended to be operated by means of an
external timer or separate remote-control system.
8. WARNING: If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or a similarly qualified person in
order to avoid a hazard.
Specifications of products
Name Model Rated
Voltage(V)
Rated
Frequency(Hz) Input Power(W)
Stand
fan YH-40A-0 AC 220-240 50 40
Please read and save this instruction manual to ensure the safe and
effective use of the applicance.
Parts diagrams:
(Ⅰ)Stand fan installation diagram
Names of parts
1. Front grill
2. Lock nut
3. Blade
4. Back nut
5. Back grill
6. Motor
7. Oscillating puller
8. Control box
years old.

4
9. Power cord
10. Control box fastening screw
11. Base
’
s upper
tube
12. Joint fastening knob
13. Base’s lower tube
14. Decorative cover
15. Base
16. Regulating switch
17. Arm Fastening knob
Schematic wiring diagram:
Installation guides:
1. Fit the rubber tips at the feet end if necessary.
2. Cross the two feets to assemble them.
3. Screw the base of the lower tube on the feets with 4 screws.

5
4. Loosen and remove the joint fastening knob and slide the decorative
cover on the base of the lower tube until it hides the fastening screws.
6. Fix the motor unit of the fan on top of the upper tube and tighten it with
the control box fastening screw.
7. Aim the locating hole of the back grill at the locating pin of front plastic
panel, and fasten it with a plastic nut.
8. Sleeve the blade center into the turning axle, then fasten the fixation
screw of the blade into the groove of the turning axle.
9. Aim the front grill locating point at the central position of the back grill,
ensure both grills aligned and fasten them with the flaps.
10. Replace the satety screw on the bottom of the grills.
5. Insert the upper tube into the lower tube and tighten the joint fastening
knob after seeting the desired height.

6
Maintenance:
1. Ensure that the fan is switched off from the supply mains before
removing the guard.
2. Don't collide with the head or strike the blades in order to prevent blade
vibration or abnormal running in the course of use.
3. After using it every year, apply appropriate clean 20# oil to the front and
back bearings of the fan motor and add some grease at other active
positions so as to extend the service life.
4.When it is not used, remove the dirt on the surface with a soft wet cloth,
and wipe it dry with dry cloth (note: don't clean the plastic parts with
gasoline, benzene and other solvents); pack it and then store in a dry and
non corrosive place.
DISPOSAL
Environmental Protection
Waste electrical production should not be disposed
of with household waste. Please recycle where
facilities exist. Check with your Local Authority or
retailer for recycling advice.