Acnodes KDS8228 User manual

All rights reserved. Product description and product specifications aresubject to changewithout notice.
For lastest product information, please visit Acnodes’ website at www.acnodes.com
14628 Central Ave. Chino, CA 91710 Tel: [phone] Fax: [phone]
© C opyright 2015 Acnodes C orp.

Chapter 1 Getting Started
1.1 Important safeguards....................................................................1
1.2 Regulatorynotice...........................................................................2
1.3 Specifications..................................................................................3
1.4 Diagram............................................................................................4
1.5 Howto install “One Man” installationslides into rack............5
1.6 How to install“One Man” installation slides.............................6
1.7 Howtouserails...............................................................................7
1.8 ConnectserverviaUSBinterface.................................................8
1.9 Keyboard&mouse.........................................................................8
1.10 HowtouseNSKeyboard...............................................................9
1.11 Optionalaccessories.......................................................................10
Chapter 2 Operation
2.1 On-screendisplayoperation.......................................................11
2.2 On-screenmenu............................................................................12
Chapter 3 Optional Specification
3.1 DCpoweroptions........................................................................13
Chapter4 KVM
4.1 ConnectviaPS/2............................................................................14
4.2 Cascade...........................................................................................15
4.3 FrontLEDIndicators.....................................................................16
4.4 KVMOSD.......................................................................................17
4.5 OSDMenu......................................................................................18
4.6 F1Menu..........................................................................................19
4.7 KVMHotkey...................................................................................20,21
4.8 KVMCables....................................................................................22
4.9 12V/24V/48VPowerInput.............................................................23
Index

1.1 ImportantSafeguards
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
What the warranty does not cover
- Any product, on which the serial number has been defaced, modified or removed.
- Damage, deterioration or malfunction resulting from:
-Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modifi- cation, or failure to follow instruc-
tions supplied with the product.
- Repair or attempted repair by anyone not authorized by us.
- Any damage of the product due to shipment.
- Removal or installation of the product.
- Causes external to the product, such as electric power fluctuation or failure.
- Use of supplies or parts not meeting our specifications.
- Normal wear and tear.
- Any other causes which does not relate to a product defect.
- Removal, installation, and set-up service charges.
CHAPTER 1
1

1.2 Regulatory Notice
Legal Information
First English printing, October 2010
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents.
The information in this document is subject to change without notice. We are not liable for any injury or loss that results from the use of this equipment.
Safety Instructions
1 Unplug equipment before cleaning. Don't use liquid or spray detergent; use a moist cloth.
2 Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned
environment with temperatures not exceeding 40º Celsius (104º Fahrenheit).
3 When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing damage to other equipment or injury
to persons nearby.
4 When the drawer is in an open position, do not cover, block or in any way obstruct the gap between it and the power supply. Proper air convection
is necessary to keep it from overheating.
5 Arrange the equipment's power cord in such a way that others won't trip or fall over it.
6 If you are using a power cord that didn't ship with the equipment, ensure that it is rated for the voltage and current labeled on the equipment's
electrical ratings label. The voltage rating on the cord should be higher than the one listed on the equipment's ratings label.
7 Observe all precautions and warnings attached to the equipment.
8 If you don't intend on using the equipment for a long time, disconnect it from the power outlet to prevent being damaged by transient over-voltage.
9 Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power supply or on other hardware
may cause damage, fire or electrical shock.
10 Only qualified service personnel should open the chassis. Opening it yourself could damage the equip- ment and invalidate its warranty.
11 If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.
RegulatoryNotices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation.
Any changes or modifications made to this equipment may void the user's authority to operate this
equipment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmfulinterference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
2

1.3 Specifications
3
Display size:
20 inches
Panel type:
ActiveMatrixTFT LCD
Resolution capabilities:
Maximum Resolution up to 1280 x 1024 (SXGA)
Brightness:
White 300 cd/m2
Contrast ratio:
1000:1
Supported colors:
16.2M Colors (6-bit withFRC)
Viewing angle:
Right-Leftview60° ~70°(Typ)
Up-DownView45° ~ 60°(Typ)
Display Area:
338 mm x 270 mm
Response Time:
RisingTime 1.3ms
LCDMTBF:
50,000hours
VGA Signal Input:
Analog H/V, Composite, SOG
Resolution:
64x400 / 720x400: 70Hz
640x480 / 800x600 /1280x1024: 60/70/72/75Hz
1024x768 /1152x864 /1280x720: 60/70/75Hz
Plus & Play DCC:
EDID1.3
Power Input:
Auto-sensing 100 to 240VAC, 50/60Hz power
LCD power consumption:
Max. 48Watts, standby 5 Watts
Keyboard & Mouse:
SUN-compatiblekeyboardintegratedwith3-button
touch-pad/trackball
KVM Ports:
8 x DB-15 Proprietary KVM Ports
KVMPorts:
Front 8 x membrane switch with indicated LEDs
KVM Membrane Switch:
1 x DB-15 proprietary cascade port, up to 128 server levelsby
8level
Certification:
CE / FCC
KVM Cable:
4-in-1 proprietary KVM cable (combo free, USBor PS/2)
Package Dimension:
442 x 650 x 44 mm / 17.4 x 25.6 x 1.73 inches
GrossWeight:
35lbs
Certification:
CE / FCC
Operation temperature:
0 ~ 50°C / 32 ~ 122°F
Storage temperature:
-20 ~ 60°C / -4 ~ 140°F
Humidity:
5~90%,non-condensing
Shock:
10Gacceleration(11msduration)
Vibration:
5~500Hz1GRMSrandom vibration
DC power input:
12 / 24 / 48VDC power input

1. Carry handle to release the 2-pt lock
2. LCD interchangeable module kit
3. “One Man” Installation Slides
4. LCD membrane
5. Membrane switch (KVM option)
6. Micro switch for screen auto power off
7. Keyboard interchangeable module kit
8. Mouse interchangeable module kit
1.4 Diagram
4

Attach the left and right mounting bracket to rack 19"
mounting rails.
Adjust the rear mounting bracket to fit your rack.
M6 screwand cup washer x 6 piece included.
Caution : Leaving the screws slightly loose, until
you complete the installation in step 4
Pick up the LCDkeyboard drawer.
Insert the LCD keyboard drawer into the mounting bracket.
Pull and hold the left & right black arrow buttons on the rails.
Return the LCD keyboard drawer to park position
1.5 How to Install “One Man” Installation Slides into rack
5

Attach front left and right mounting ears of the LCD
keyboard drawer to vertical mounting rails.
? M6 screw and cup washer x 2 pcs included.
Complete the installation
? Tighten all 8 piece of M6 screw to complete the installation
1.6 How to Install “One Man” Installation Slides
6

?Ablack arrow release button is
located on the outside of each
slide. (shown in Figure 1).
Pull and hold the black arrow button on
either side of the LCD keyboard drawer to
unlock. (shown in Figure 2).
? Push the LCD keyboard drawer into
the rack. (shown in Figure 3).
Caution : Keep your fingers away from
the slide stop
1.7 How to Use the Slides
7

IntegratedKeyboardwithtouchpad
-IncorporatesSUNkeys includingStop,Cut,Paste,Compose,Copy,andHelp.
-104KeynotepadkeyboardwithfullnermicalpadandSUNfunction
-UsbInterface
-OptionalNKeyboardintegratedwithtrackball
Exampleofconnecting 2-in-1USBKVMcabletoserverviaUSBinterface
1.8 Connect server via USB inteface
8
1.9 Keyboard and Mouse
STANDARD: